WiFi Question

wallabybob

I could not figure out how connect the pfsense wifi card to the existing AP. iwn0 is setup as the WAN interface.

I presume you mean configure rather than connect.
On the Interfaces -> WAN page in the Network-specific wireless configuration set the Mode to Infrastructure (to connect to an existing AP), set the SSID to the WiFi network name configured in the AP and set the encryption parameters (if used) to match what is set in the AP (encryption mode, password etc).

The General Configuration parameters should be set the same as you would set for a wired interface.

wallabybob

@kejianshi:

if your problem is that your wireless card is being shown as WAN

My reading of the original post is that is what is required as a temporary replacement for a damaged wired link. I suspect this is a "get something working quickly with what is already available" problem rather than a "what is the optimum way of putting a WiFi access point on a network with pfSense present" question.

kejianshi

I think you are probably correct.

t_enriquez

That is correct. This is a temp solution with already available resources.

t_enriquez

Thanks for all of the replies. I finally have the WiFi "configured" correctly. I tried to "bridge" the two interfaces and it looks like my WiFi adapter will not work.

I'll have to make a few changes to the devices to use the WiFi through the pfsense box.

FYI, the computer is a Foxconn nT-i1200-0H0WBNA.

Thanks again for the replies

t_enriquez

@t_enriquez:

Thanks for all of the replies. I finally have the WiFi "configured" correctly. I tried to "bridge" the two interfaces and it looks like my WiFi adapter will not work.

I'll have to make a few changes to the devices to use the WiFi through the pfsense box.

FYI, the computer is a Foxconn nT-i1200-0H0WBNA.

Thanks again for the replies

The error when trying to create the bridge was:

The following input errors were detected:

Bridging a wireless interface is only possible in hostap mode.

wallabybob

@t_enriquez:

The error when trying to create the bridge was:

The following input errors were detected:

Bridging a wireless interface is only possible in hostap mode.

I don't know the reason for that restriction. Why do you need to bridge?

stan-qaz

I'd really lean to external wireless extenders.

Cheap $60, not so fast: http://www.newegg.com/Product/Product.aspx?Item=N82E16833127294

More $120 pretty fast: http://www.newegg.com/Product/Product.aspx?Item=9SIA0SF0BV4130

I use a 1525 in bridge mode to get my Ethernet to a printer and a backup drive sitting in a spot that it would be hard to get cables to. It runs for months on end with no hassles and recovers from power outages with no problems. Other brands might work better but I got the DAP really cheap.

t_enriquez

@wallabybob:

@t_enriquez:

The error when trying to create the bridge was:

The following input errors were detected:

Bridging a wireless interface is only possible in hostap mode.

I don't know the reason for that restriction. Why do you need to bridge?

I need to bridge to keep the lan segment the same on both sides.

t_enriquez

@stan-qaz:

I'd really lean to external wireless extenders.

Cheap $60, not so fast: http://www.newegg.com/Product/Product.aspx?Item=N82E16833127294

More $120 pretty fast: http://www.newegg.com/Product/Product.aspx?Item=9SIA0SF0BV4130

I use a 1525 in bridge mode to get my Ethernet to a printer and a backup drive sitting in a spot that it would be hard to get cables to. It runs for months on end with no hassles and recovers from power outages with no problems. Other brands might work better but I got the DAP really cheap.

Thanks for the reply. I'll check them out if we can't run the new cable right away.