Looking for help re-arranging my network
-
So your Pc is connected to lan port of dd-wrt router, your pfsense is connect to different lan port on dd-wrt router. Your PC got an IP from pfsense dhcp??
On 192.168.1.0/24 and you can ping pfsense lan port.. But you can not access dd-wrt on 192.168.1.2??
Then you did not correctly set its IP.. Or you have a mac address issue, or dd-wrt is broken ;) since its switch ports are currently working any your cables are good if you can talk to pfsense through your dd-wrt lan ports.
Why are you apposed to hard reset? It takes 2 minutes to set it up as AP from default..
That's exactly what's happening. Both on the same subnet. PC got served an IP from pfSense through DD-WRT Lan port.
Ughh. I'll do a hard reset then.
-
Short answer is yes. You could continue without a reset.
However if there is a typo or something in there, you would end up wasting hours or days vs minutes on the reset.Other advice. In that DDWRT document. Use the long version.
Also:
Instep 3: All the so-called optional stuff is mandatory and turn off NTP in DDWRT
Open the Setup -> Basic Setup tab
WAN Connection Type : Disabled
Local IP Address: 192.168.1.2 (i.e. different from primary router and out of primary router's DHCP pool)
Subnet Mask: 255.255.255.0 (i.e. same as primary router)
DHCP Server: Disable (also uncheck DNSmasq options)
(Recommended) Gateway/Local DNS: Make sure you use 192.168.1.1 here if thats what you set as pfsense LAN!!!!!!
(Optional) Assign WAN Port to Switch (visible only with WAN Connection Type set to disabled): Enable this if you want to use WAN port as a switch port
(Optional) NTP Client: Enable/Disable (if Enabled, specify Gateway/Local DNS above)in step 7, none of that is optional. Its mandatory.
Open the Services -> Services tab
(Optional) DNSMasq: Disable (enable if you use additional DNSMasq settings)
(Optional) ttraff Daemon: Disable
Savein step 9, all those recommended settings are not recommended. They are mandatory.
Open the Administration -> Management tab
(Recommended) Info Site Password Protection: Enable
(Recommended) Routing: Disabled (enable if you need to route between interfaces)
Apply Settings and connect Ethernet cable to main router via LAN-to-LAN uplink*
Reboot router to be sure all settings have been applied.
You may have to reboot your own PC or do "ipconfig /release" + "ipconfig /renew" from the Windows command line.If you were to follow this guide, omitting the "optional" settings, it wouldn't work for you.
-
Look up at my setting I added in previous comment also.
(Recommended) Gateway/Local DNS: Make sure you use 192.168.1.1 here if thats what you set as pfsense LAN!!!!!!
-
"They are mandatory."
BS – sorry but you sure an the hell do not need to put wan port into your switch ports, nor do you have to setup gateway or dns on your lan.. In what case does the web ui or dd-wrt need to know how to get off its network to be a AP??
And you sure and the hell do not need to disable routing -- your not using it, but does not mean it can not be ON...
Those settings are all tweaks and not "mandatory" that is for damn sure -- Give it an IP you can access is not even really required!! the only thing required is turn off its freaking dhcp server or your going to have problems!!! But it really does not need an IP on the current network if your wireless is setup how you want it all ready.. Or you don't mind putting a pc on its network to access the gui, etc..
Not sure where your getting mandatory anything from those settings - your just trying to confuse him or make it seem more complicated??
-
Also, No, I do understand how these things work. I know pfSense won't be giving the router an IP.
I just said that in response to someone asking.Short answer is yes. You could continue without a reset.
However if there is a typo or something in there, you would end up wasting hours or days vs minutes on the reset.Other advice. In that DDWRT document. Use the long version.
Also:
Instep 3: All the so-called optional stuff is mandatory and turn off NTP in DDWRT
Open the Setup -> Basic Setup tab
WAN Connection Type : Disabled
Local IP Address: 192.168.1.2 (i.e. different from primary router and out of primary router's DHCP pool)
Subnet Mask: 255.255.255.0 (i.e. same as primary router)
DHCP Server: Disable (also uncheck DNSmasq options)
(Recommended) Gateway/Local DNS: Make sure you use 192.168.1.1 here if thats what you set as pfsense LAN!!!!!!
(Optional) Assign WAN Port to Switch (visible only with WAN Connection Type set to disabled): Enable this if you want to use WAN port as a switch port
(Optional) NTP Client: Enable/Disable (if Enabled, specify Gateway/Local DNS above)in step 7, none of that is optional. Its mandatory.
Open the Services -> Services tab
(Optional) DNSMasq: Disable (enable if you use additional DNSMasq settings)
(Optional) ttraff Daemon: Disable
Savein step 9, all those recommended settings are not recommended. They are mandatory.
Open the Administration -> Management tab
(Recommended) Info Site Password Protection: Enable
(Recommended) Routing: Disabled (enable if you need to route between interfaces)
Apply Settings and connect Ethernet cable to main router via LAN-to-LAN uplink*
Reboot router to be sure all settings have been applied.
You may have to reboot your own PC or do "ipconfig /release" + "ipconfig /renew" from the Windows command line.If you were to follow this guide, omitting the "optional" settings, it wouldn't work for you.
Thank you very much for all your time. This seems to have worked. I also put the hostname I specified in pfSense into DD-WRT this time. Everything seems to be working now.
I'll reboot both "routers" and see if it keeps working. Then I'll report back.
-
I'm glad its all good…
-
I'm back. I had a small issue with the 5GHz radio in DD-WRT, but restarting it again solved it.
Everything it working great.Thank you, all.
Is there a thanking or rep system on this forum I could use to show my gratitude? -
Yes - I have a Bank Routing Number and Account Number for expressing appreciation…
(kidding - I don't think there is anything like that on this site)
-
Yes - I have a Bank Routing Number and Account Number for expressing appreciation…
(kidding - I don't think there is anything like that on this site)
LOL ;D
Well, thanks again. -
Yes - I have a Bank Routing Number and Account Number for expressing appreciation…
I only take beer… so, if you manage to set up beer-over-ip tunnel, I'll be happy to be your guest. :D
