IPsec won't pass data after a client disconnects and reconnects

kejianshi

I would say thats not exactly true, although it would be nice if it were.
This traffic not passing condition is constant and reproducible 100% of the time for me.

Disconnect, wait a few seconds or couple of minutes with a mobile client and it will consistently not be able to access the web or the site behind the pfsense. Wait a good while longer to try a reconnect and it will work again or do a reset of raccoon and it will work again.

I don't use ipsec much but this is always the case with mobile client quick disconnect and reconnect.
One would think it wouldn't be that big of an issue, but with mobile clients you disconnect and reconnect often.

jimp

On 2.0.3 or 2.1?

We have several confirmed reports of it working fine on 2.1. There is an open ticket for that problem.
https://redmine.pfsense.org/issues/1351

kejianshi

I'm using 2.03, but people are still reporting the same behaviour in 2.1

As of yesterday. Still time to get it worked into the 2.1 release? (-:

jimp

If it's actually broken on 2.1, yes.

The people I saw that are still broken on 2.1 are not using the required settings to make it work as defined on http://doc.pfsense.org/index.php/Mobile_IPsec_on_2.0

Anyone I'm aware of using the proper settings on 2.1 is working.

kejianshi

Why you would prefer 24 hours in phase 1 but 8 in phase two? Lifetime: 86400 and Lifetime: 28800 is unclear to me, but I've done that.
No difference in behaviour from both being same 28800 for me.
Makes no mention of NAT-T? Mine is enabled.
Uncheck "Prefer Old IPsec SA" - Makes no diff for me.
Strict vs obey seems to also make no diff. for me except perhaps in timeout (many hours).

With all settings, checked, rechecked, triple checked, checked to death, disconnect then reconnect within minutes is not reliable.
If I disconnect a few seconds, then reconnect it will pass traffic. (sometimes)
If I disconnect wait 5 minutes and reconnect it won't pass traffic. (always)
If I disconnect and wait an hour, it will work. (I say 1 hour, but it could be a little longer or shorter)
I seriously doubt this issue is fixed in 2.1 either, since people are still mentioning it and saying they are on 2.1

That said, looks you have addressed alot in ipsec for 2.1 to make it more reliable,
mainly changes and drops in the SERVER's IP, not so much client drops and login / logouts.

jimp

The settings have been determined after a ton of work and tested to work on Android and iOS both. These are the settings that work, use them, you can't change them without breaking one platform or another. The settings aren't really a guide or suggestions, you must use them exactly and not deviate, or you will have problems.

It mentions NAT-T ("NAT Traversal: Force")

And yes, it works on 2.1 with current snapshots. Don't make assumptions until you have tested it personally on 2.1 and have verified every single setting on that page.

2.0.3 is known to be broken, as was 2.1 a few weeks ago, but it has been fixed since then (see the ticket I linked earlier).

kejianshi

haha. I like your attitude. No taking crap from a newbie.
I will do. I'll set up a 2.1 box and test it with exactly this setting.
I don't use ipsec myself much, so my interest is purely to improve pfsense, which I really like.

orald

Unfortunately, I have to confirm that 2.1-RC1 (amd64) built on Sat Aug 24 12:23:49 EDT 2013 connected with Cisco VPN client (IPsec ) is still vulnerable :'(. My IPsec log contains:

Aug 25 18:23:24: racoon: ERROR: no configuration found for 77.253.100.xxx.
Aug 25 18:23:24: racoon: ERROR: failed to begin ipsec sa negotication.

SAD table shows:

Source ▴ 	Destination 	Protocol 	SPI 	Enc. alg. 	Auth. alg. 	Data 	
xxx.xxx.xxx.xxx[4500] 	77.253.100.xxx[62460] 	ESP-UDP 	7074425e 	aes-cbc 	hmac-md5 	0 B
77.253.100.xxx[62460] 	xxx.xxx.xxx.xxx[4500] 	ESP-UDP 	09007124 	aes-cbc 	hmac-md5 	27524 B

It is look like there is no traffic passed to mobile client. More the traffic is blocked permanently and I can not find any solutions to solve it.

jimp

Make sure you review every single setting here:
http://doc.pfsense.org/index.php/Mobile_IPsec_on_2.0

If it still doesn't work, blame the Cisco IPsec Client. Especially the Windows one, from Cisco, will not play well with anything but Cisco. If you connect to anything but a Cisco device with the Windows client, you're actually violating its license. (AFAIK, iOS, Android, and OS X are all OK)

If you must use IPsec from Windows, use the Shrew Soft client.

kejianshi

That reads more like there is a problem with either the phase 1 or phase 2 config than the error I was talking about.

The error I was concerned with did allow connections, it just didn't reliably reconnect in a timely manner after a short disconnect.