WatchGuard x750e, HDD install and pfSense 2.1

stephenw10

The CF slot in the X750e is always the primary master (ad0) so it's recommended you have the HD set as primary slave (ad1) in case you have a CF card in the slot. If it's set to cable select it should come up as slave anyway. It looks like you don't have that and your drive is set asl master. I would expect the correct line to be:

ufs:/dev/ad0s1a

Interesting that it shows ad0 and ad1 though.

The partitioning scheme may have changed under 2.1 if you have SATA drives that are now correctly seen in AHCI mode. They may now appear as ada0 etc. This has caught out some people upgrading. The X750e isn't using SATA so not worries there.

Steve

zero

Steve, thanks for the fast reply :)

Everything has been done the way you described it. CF card is master (still in the slot) and HDD is set to slave (with jumper). I tried ufs:/dev/ad0s1a as well, but without success.

stephenw10

Hmm, Ok. Well 100GB is somewhere between the 40GB drive I used and the 120Gb drive that worked perfectly. The drive geometry is key here but quite what is required is unknown.
Did you choose 'verbose boot' at the boot loader menu?
Try to log the startup messages and post them here. The details of the detected drives should show what's happening or not happening.

Steve

zero

This is the verbose log:


KDB: debugger backends: ddb
KDB: current backend: ddb
SMAP type=01 base=0000000000000000 len=000000000009f800
SMAP type=02 base=00000000000f0000 len=0000000000010000
SMAP type=02 base=00000000fec00000 len=0000000000001000
SMAP type=02 base=00000000fee00000 len=0000000000001000
SMAP type=02 base=00000000ffb00000 len=0000000000500000
SMAP type=02 base=00000000e0000000 len=0000000010000000
SMAP type=02 base=000000000009f800 len=0000000000000800
SMAP type=01 base=0000000000100000 len=000000003f700000
Copyright (c) 1992-2012 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.3-RELEASE-p11 #0: Wed Sep 11 18:39:44 EDT 2013
    root@snapshots-8_3-i386.builders.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.8 i386
Preloaded elf kernel "/boot/kernel/kernel" at 0xc17b6000.
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 1600067815 Hz
CPU: Intel(R) Pentium(R) M processor 1.60GHz (1600.07-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x6d6  Family = 6  Model = d  Stepping = 6
  Features=0xafe9fbbf <fpu,vme,de,pse,tsc,msr,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,tm,pbe>Features2=0x180 <est,tm2>Instruction TLB: 4 KB Pages, 4-way set associative, 128 entries
Data TLB: 4 KB Pages, 4-way set associative, 128 entries
Instruction TLB: 4 MB pages, fully associative, 2 entries
2nd-level cache: 2-MB, 8-way set associative, 64-byte line size
1st-level instruction cache: 32 KB, 8-way set associative, 64 byte line size
Data TLB: 4 MB Pages, 4-way set associative, 8 entries
1st-level data cache: 32 KB, 8-way set associative, 64 byte line size
real memory  = 1065353216 (1016 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000001826000 - 0x000000003e5d8fff, 1020997632 bytes (249267 pages)
avail memory = 1019412480 (972 MB)
ACPI Error: A valid RSDP was not found (20101013/tbxfroot-309)
MP Configuration Table version 1.4 found at 0xc00f0c00
APIC: Using the MPTable enumerator.
SMP: Added CPU 0 (BSP)
MPTable: <oem00000 prod00000000="">bios32: Found BIOS32 Service Directory header at 0xc00f9930
bios32: Entry = 0xf9f40 (c00f9f40)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0xf0000+0x9f70
pnpbios: Found PnP BIOS data at 0xc00faa60
pnpbios: Entry = f0000:aa90  Rev = 1.0
Other BIOS signatures found:
x86bios:   IVT 0x000000-0x0004ff at 0xc0000000
x86bios:  SSEG 0x010000-0x01ffff at 0xc4794000
x86bios:  EBDA 0x09f000-0x09ffff at 0xc009f000
x86bios:   ROM 0x0a0000-0x0effff at 0xc00a0000
ULE: setup cpu 0
ioapic0: Assuming intbase of 0
ioapic0: Routing external 8259A's -> intpin 0
ioapic0: Routing IRQ 0 -> intpin 2
lapic: Routing ExtINT -> LINT0
lapic: Routing NMI -> LINT1
ioapic0 <version 2.0="">irqs 0-23 on motherboard
cpu0 BSP:
     ID: 0x00000000   VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
  timer: 0x000100ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
firmware: 'iwn6000g2afw' version 0: 444128 bytes loaded at 0xc12672fc
firmware: 'iwn6000g2bfw' version 0: 460912 bytes loaded at 0xc12d3a54
wlan: mac acl policy registered
firmware: 'iwn6050fw' version 0: 469780 bytes loaded at 0xc134433c
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xc07bb6f0, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xc07bb790, 0) error 1
firmware: 'mw88W8363fw' version 0: 94940 bytes loaded at 0xc13bcf84
firmware: 'mwlboot' version 0: 2280 bytes loaded at 0xc13d4260
firmware: 'mxge_eth_z8e' version 375636: 119802 bytes loaded at 0xc13d4d40
wlan: <802.11 Link Layer>
firmware: 'mxge_ethp_z8e' version 385956: 120433 bytes loaded at 0xc13f21c0
firmware: 'mxge_rss_eth_z8e' version 561364: 157863 bytes loaded at 0xc140f8c0
firmware: 'mxge_rss_ethp_z8e' version 571764: 158985 bytes loaded at 0xc14361e0
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xc07bb830, 0) error 1
firmware: 'iwn1000fw' version 0: 337520 bytes loaded at 0xc10d2350
firmware: 'rt2561fw' version 0: 8192 bytes loaded at 0xc1460b30
firmware: 'rt2561sfw' version 0: 8192 bytes loaded at 0xc1462ba8
firmware: 'rt2661fw' version 0: 8192 bytes loaded at 0xc1464c20
firmware: 'rt2860fw' version 0: 8192 bytes loaded at 0xc1466c98
firmware: 'iwn4965fw' version 0: 187972 bytes loaded at 0xc1124a38
firmware: 'iwn5000fw' version 0: 340696 bytes loaded at 0xc11528f4
firmware: 'wpifw' version 2144: 149652 bytes loaded at 0xc14ab310
firmware: 'iwn5150fw' version 0: 337400 bytes loaded at 0xc11a5c44
firmware: 'iwn6000fw' version 0: 454608 bytes loaded at 0xc11f82b4
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>Pentium Pro MTRR support enabled
nfslock: pseudo-device
crypto: <crypto core="">null: <null device,="" zero="" device="">io: _random: <entropy source,="" software,="" yarrow="">hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2
ACPI Error: A valid RSDP was not found (20101013/tbxfroot-309)
ACPI: Table initialisation failed: AE_NOT_FOUND
ACPI: Try disabling either ACPI or apic support.
cryptosoft0: <software crypto="">on motherboard
crypto: assign cryptosoft0 driver id 0, flags 100663296
crypto: cryptosoft0 registers alg 1 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 2 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 3 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 4 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 5 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 16 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 6 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 7 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 18 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 19 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 20 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 8 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 15 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 9 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 10 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 13 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 14 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 11 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 22 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 21 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 17 flags 0 maxoplen 0
padlock0: No ACE support.
pci_open(1):    mode 1 addr port (0x0cf8) is 0x8000f904
pci_open(1a):   mode1res=0x80000000 (0x80000000)
pci_cfgcheck:   device 0 [class=060000] [hdr=00] is there (id=25908086)
pcibios: BIOS version 3.00
PCIe: Memory Mapped configuration base @ 0xe0000000
pcib0: <mptable host-pci="" bridge="">pcibus 0 on motherboard
pci0: <pci bus="">on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x8086, dev=0x2590, revid=0x04
        domain=0, bus=0, slot=0, func=0
        class=06-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0006, statreg=0x2090, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2592, revid=0x04
        domain=0, bus=0, slot=2, func=0
        class=03-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=11
        powerspec 2  supports D0 D3  current D0
        map[10]: type Memory, range 32, base 0xd0500000, size 19, enabled
        map[14]: type I/O Port, range 32, base 0xea00, size  3, enabled
        map[18]: type Prefetchable Memory, range 32, base 0xc0000000, size 28, enabled
        map[1c]: type Memory, range 32, base 0xd0580000, size 18, enabled
pcib0: slot 2 INTA routed to irq 16
found-> vendor=0x8086, dev=0x2660, revid=0x04
        domain=0, bus=0, slot=28, func=0
        class=06-04-00, hdrtype=0x01, mfdev=1
        cmdreg=0x0107, statreg=0x0010, cachelnsz=8 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=11
        powerspec 2  supports D0 D3  current D0
        MSI supports 1 message
pcib0: slot 28 INTA routed to irq 16
found-> vendor=0x8086, dev=0x2662, revid=0x04
        domain=0, bus=0, slot=28, func=1
        class=06-04-00, hdrtype=0x01, mfdev=1
        cmdreg=0x0107, statreg=0x0010, cachelnsz=8 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
        intpin=b, irq=12
        powerspec 2  supports D0 D3  current D0
        MSI supports 1 message
pcib0: slot 28 INTB routed to irq 17
found-> vendor=0x8086, dev=0x2664, revid=0x04
        domain=0, bus=0, slot=28, func=2
        class=06-04-00, hdrtype=0x01, mfdev=1
        cmdreg=0x0107, statreg=0x0010, cachelnsz=8 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
        intpin=c, irq=5
        powerspec 2  supports D0 D3  current D0
        MSI supports 1 message
pcib0: slot 28 INTC routed to irq 18
found-> vendor=0x8086, dev=0x2666, revid=0x04
        domain=0, bus=0, slot=28, func=3
        class=06-04-00, hdrtype=0x01, mfdev=1
        cmdreg=0x0107, statreg=0x0010, cachelnsz=8 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
        intpin=d, irq=10
        powerspec 2  supports D0 D3  current D0
        MSI supports 1 message
pcib0: slot 28 INTD routed to irq 19
found-> vendor=0x8086, dev=0x2658, revid=0x04
        domain=0, bus=0, slot=29, func=0
        class=0c-03-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=9
        map[20]: type I/O Port, range 32, base 0xeb00, size  5, enabled
pcib0: slot 29 INTA routed to irq 23
unknown: Reserved 0x20 bytes for rid 0x20 type 4 at 0xeb00
found-> vendor=0x8086, dev=0x2659, revid=0x04
        domain=0, bus=0, slot=29, func=1
        class=0c-03-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=b, irq=10
        map[20]: type I/O Port, range 32, base 0xed00, size  5, enabled
pcib0: slot 29 INTB routed to irq 19
unknown: Reserved 0x20 bytes for rid 0x20 type 4 at 0xed00
found-> vendor=0x8086, dev=0x265a, revid=0x04
        domain=0, bus=0, slot=29, func=2
        class=0c-03-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=c, irq=5
        map[20]: type I/O Port, range 32, base 0xe800, size  5, enabled
pcib0: slot 29 INTC routed to irq 18
unknown: Reserved 0x20 bytes for rid 0x20 type 4 at 0xe800
found-> vendor=0x8086, dev=0x265b, revid=0x04
        domain=0, bus=0, slot=29, func=3
        class=0c-03-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=d, irq=11
        map[20]: type I/O Port, range 32, base 0xe900, size  5, enabled
pcib0: slot 29 INTD routed to irq 16
unknown: Reserved 0x20 bytes for rid 0x20 type 4 at 0xe900
found-> vendor=0x8086, dev=0x265c, revid=0x04
        domain=0, bus=0, slot=29, func=7
        class=0c-03-20, hdrtype=0x00, mfdev=0
        cmdreg=0x0006, statreg=0x0290, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=9
        powerspec 2  supports D0 D3  current D0
        map[10]: type Memory, range 32, base 0xd05c0000, size 10, enabled
pcib0: slot 29 INTA routed to irq 23
unknown: Reserved 0x400 bytes for rid 0x10 type 3 at 0xd05c0000
found-> vendor=0x8086, dev=0x2448, revid=0xd4
        domain=0, bus=0, slot=30, func=0
        class=06-04-01, hdrtype=0x01, mfdev=0
        cmdreg=0x0107, statreg=0x0010, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2641, revid=0x04
        domain=0, bus=0, slot=31, func=0
        class=06-01-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0107, statreg=0x0200, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x266f, revid=0x04
        domain=0, bus=0, slot=31, func=1
        class=01-01-8a, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x0288, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=255
        map[20]: type I/O Port, range 32, base 0xf000, size  4, enabled
found-> vendor=0x8086, dev=0x266a, revid=0x04
        domain=0, bus=0, slot=31, func=3
        class=0c-05-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=b, irq=10
        map[20]: type I/O Port, range 32, base 0x500, size  5, enabled
pcib0: slot 31 INTB routed to irq 19
vgapci0: <vga-compatible display="">port 0xea00-0xea07 mem 0xd0500000-0xd057ffff,0xc0000000-0xcfffffff,0xd0580000-0xd05bffff irq 160
agp0: <intel 82915gm="" (915gm="" gmch)="" svga="" controller="">on vgapci0
vgapci0: Reserved 0x10000000 bytes for rid 0x18 type 3 at 0xc0000000
vgapci0: Reserved 0x80000 bytes for rid 0x10 type 3 at 0xd0500000
vgapci0: Reserved 0x40000 bytes for rid 0x1c type 3 at 0xd0580000
agp0: aperture size is 256M, detected 7932k stolen memory
pcib1: <mptable pci-pci="" bridge="">irq 16 at device 28.0 on pci0
pcib1:   domain            0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   I/O decode        0x8000-0x8fff
pcib1:   memory decode     0xd0000000-0xd00fffff
pcib1:   no prefetched decode
pci1: <pci bus="">on pcib1
pci1: domain=0, physical bus=1
found-> vendor=0x11ab, dev=0x4362, revid=0x19
        domain=0, bus=1, slot=0, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=11
        powerspec 2  supports D0 D1 D2 D3  current D0
        MSI supports 2 messages, 64 bit
        map[10]: type Memory, range 64, base 0xd0020000, size 14, enabled
pcib1: requested memory range 0xd0020000-0xd0023fff: good
        map[18]: type I/O Port, range 32, base 0x8000, size  8, enabled
pcib1: requested I/O range 0x8000-0x80ff: in range
pcib1: slot 0 INTA routed to irq 16
mskc0: <marvell yukon="" 88e8053="" gigabit="" ethernet="">port 0x8000-0x80ff mem 0xd0020000-0xd0023fff irq 16 at device 0.0 on pci1
mskc0: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xd0020000
mskc0: MSI count : 2
mskc0: attempting to allocate 1 MSI vectors (2 supported)
msi: routing MSI IRQ 256 to local APIC 0 vector 48
mskc0: using IRQ 256 for MSI
mskc0: RAM buffer size : 48KB
mskc0: Port 0 : Rx Queue 32KB(0x00000000:0x00007fff)
mskc0: Port 0 : Tx Queue 16KB(0x00008000:0x0000bfff)
msk0: <marvell technology="" group="" ltd.="" yukon="" ec="" id="" 0xb6="" rev="" 0x02="">on mskc0
msk0: bpf attached
miibus0: <mii bus="">on msk0
e1000phy0: <marvell 88e1111="" gigabit="" phy="">PHY 0 on miibus0
e1000phy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-mastew
mskc0: [MPSAFE]
mskc0: [ITHREAD]
pcib2: <mptable pci-pci="" bridge="">irq 17 at device 28.1 on pci0
pcib2:   domain            0
pcib2:   secondary bus     2
pcib2:   subordinate bus   2
pcib2:   I/O decode        0x9000-0x9fff
pcib2:   memory decode     0xd0100000-0xd01fffff
pcib2:   no prefetched decode
pci2: <pci bus="">on pcib2
pci2: domain=0, physical bus=2
found-> vendor=0x11ab, dev=0x4362, revid=0x19
        domain=0, bus=2, slot=0, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=12
        powerspec 2  supports D0 D1 D2 D3  current D0
        MSI supports 2 messages, 64 bit
        map[10]: type Memory, range 64, base 0xd0120000, size 14, enabled
pcib2: requested memory range 0xd0120000-0xd0123fff: good
        map[18]: type I/O Port, range 32, base 0x9000, size  8, enabled
pcib2: requested I/O range 0x9000-0x90ff: in range
pcib2: slot 0 INTA routed to irq 17
mskc1: <marvell yukon="" 88e8053="" gigabit="" ethernet="">port 0x9000-0x90ff mem 0xd0120000-0xd0123fff irq 17 at device 0.0 on pci2
mskc1: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xd0120000
mskc1: MSI count : 2
mskc1: attempting to allocate 1 MSI vectors (2 supported)
msi: routing MSI IRQ 257 to local APIC 0 vector 49
mskc1: using IRQ 257 for MSI
mskc1: RAM buffer size : 48KB
mskc1: Port 0 : Rx Queue 32KB(0x00000000:0x00007fff)
mskc1: Port 0 : Tx Queue 16KB(0x00008000:0x0000bfff)
msk1: <marvell technology="" group="" ltd.="" yukon="" ec="" id="" 0xb6="" rev="" 0x02="">on mskc1
msk1: bpf attached
miibus1: <mii bus="">on msk1
e1000phy1: <marvell 88e1111="" gigabit="" phy="">PHY 0 on miibus1
e1000phy1:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-mastew
mskc1: [MPSAFE]
mskc1: [ITHREAD]
pcib3: <mptable pci-pci="" bridge="">irq 18 at device 28.2 on pci0
pcib3:   domain            0
pcib3:   secondary bus     3
pcib3:   subordinate bus   3
pcib3:   I/O decode        0xa000-0xafff
pcib3:   memory decode     0xd0200000-0xd02fffff
pcib3:   no prefetched decode
pci3: <pci bus="">on pcib3
pci3: domain=0, physical bus=3
found-> vendor=0x11ab, dev=0x4362, revid=0x19
        domain=0, bus=3, slot=0, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=5
        powerspec 2  supports D0 D1 D2 D3  current D0
        MSI supports 2 messages, 64 bit
        map[10]: type Memory, range 64, base 0xd0220000, size 14, enabled
pcib3: requested memory range 0xd0220000-0xd0223fff: good
        map[18]: type I/O Port, range 32, base 0xa000, size  8, enabled
pcib3: requested I/O range 0xa000-0xa0ff: in range
pcib3: slot 0 INTA routed to irq 18
mskc2: <marvell yukon="" 88e8053="" gigabit="" ethernet="">port 0xa000-0xa0ff mem 0xd0220000-0xd0223fff irq 18 at device 0.0 on pci3
mskc2: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xd0220000
mskc2: MSI count : 2
mskc2: attempting to allocate 1 MSI vectors (2 supported)
msi: routing MSI IRQ 258 to local APIC 0 vector 50
mskc2: using IRQ 258 for MSI
mskc2: RAM buffer size : 48KB
mskc2: Port 0 : Rx Queue 32KB(0x00000000:0x00007fff)
mskc2: Port 0 : Tx Queue 16KB(0x00008000:0x0000bfff)
msk2: <marvell technology="" group="" ltd.="" yukon="" ec="" id="" 0xb6="" rev="" 0x02="">on mskc2
msk2: bpf attached
miibus2: <mii bus="">on msk2
e1000phy2: <marvell 88e1111="" gigabit="" phy="">PHY 0 on miibus2
e1000phy2:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-mastew
mskc2: [MPSAFE]
mskc2: [ITHREAD]
pcib4: <mptable pci-pci="" bridge="">irq 19 at device 28.3 on pci0
pcib4:   domain            0
pcib4:   secondary bus     4
pcib4:   subordinate bus   4
pcib4:   I/O decode        0xb000-0xbfff
pcib4:   memory decode     0xd0300000-0xd03fffff
pcib4:   no prefetched decode
pci4: <pci bus="">on pcib4
pci4: domain=0, physical bus=4
found-> vendor=0x11ab, dev=0x4362, revid=0x19
        domain=0, bus=4, slot=0, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=10
        powerspec 2  supports D0 D1 D2 D3  current D0
        MSI supports 2 messages, 64 bit
        map[10]: type Memory, range 64, base 0xd0320000, size 14, enabled
pcib4: requested memory range 0xd0320000-0xd0323fff: good
        map[18]: type I/O Port, range 32, base 0xb000, size  8, enabled
pcib4: requested I/O range 0xb000-0xb0ff: in range
pcib4: slot 0 INTA routed to irq 19
mskc3: <marvell yukon="" 88e8053="" gigabit="" ethernet="">port 0xb000-0xb0ff mem 0xd0320000-0xd0323fff irq 19 at device 0.0 on pci4
mskc3: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xd0320000
mskc3: MSI count : 2
mskc3: attempting to allocate 1 MSI vectors (2 supported)
msi: routing MSI IRQ 259 to local APIC 0 vector 51
mskc3: using IRQ 259 for MSI
mskc3: RAM buffer size : 48KB
mskc3: Port 0 : Rx Queue 32KB(0x00000000:0x00007fff)
mskc3: Port 0 : Tx Queue 16KB(0x00008000:0x0000bfff)
msk3: <marvell technology="" group="" ltd.="" yukon="" ec="" id="" 0xb6="" rev="" 0x02="">on mskc3
msk3: bpf attached
miibus3: <mii bus="">on msk3
e1000phy3: <marvell 88e1111="" gigabit="" phy="">PHY 0 on miibus3
e1000phy3:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-mastew
mskc3: [MPSAFE]
mskc3: [ITHREAD]
uhci0: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-a="">port 0xeb00-0xeb1f irq 23 at device 29.0 on pci0
ioapic0: routing intpin 23 (PCI IRQ 23) to lapic 0 vector 52
uhci0: [MPSAFE]
uhci0: [ITHREAD]
uhci0: LegSup = 0x2f00
usbus0: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-a="">on uhci0
uhci1: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-b="">port 0xed00-0xed1f irq 19 at device 29.1 on pci0
ioapic0: routing intpin 19 (PCI IRQ 19) to lapic 0 vector 53
uhci1: [MPSAFE]
uhci1: [ITHREAD]
uhci1: LegSup = 0x2f00
usbus1: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-b="">on uhci1
uhci2: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-c="">port 0xe800-0xe81f irq 18 at device 29.2 on pci0
ioapic0: routing intpin 18 (PCI IRQ 18) to lapic 0 vector 54
uhci2: [MPSAFE]
uhci2: [ITHREAD]
uhci2: LegSup = 0x2f00
usbus2: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-c="">on uhci2
uhci3: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-d="">port 0xe900-0xe91f irq 16 at device 29.3 on pci0
ioapic0: routing intpin 16 (PCI IRQ 16) to lapic 0 vector 55
uhci3: [MPSAFE]
uhci3: [ITHREAD]
uhci3: LegSup = 0x2f00
usbus3: <intel 82801fb="" fr="" fw="" frw="" (ich6)="" usb="" controller="" usb-d="">on uhci3
ehci0: <intel 82801fb="" (ich6)="" usb="" 2.0="" controller="">mem 0xd05c0000-0xd05c03ff irq 23 at device 29.7 on pci0
ehci0: [MPSAFE]
ehci0: [ITHREAD]
usbus4: EHCI version 1.0
usbus4: <intel 82801fb="" (ich6)="" usb="" 2.0="" controller="">on ehci0
pcib5: <mptable pci-pci="" bridge="">at device 30.0 on pci0
pcib5:   domain            0
pcib5:   secondary bus     5
pcib5:   subordinate bus   5
pcib5:   I/O decode        0xc000-0xdfff
pcib5:   memory decode     0xd0400000-0xd04fffff
pcib5:   no prefetched decode
pcib5:   Subtractively decoded bridge.
pci5: <pci bus="">on pcib5
pci5: domain=0, physical bus=5
found-> vendor=0x11ab, dev=0x4320, revid=0x13
        domain=0, bus=5, slot=0, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords)
        lattimer=0x60 (2880 ns), mingnt=0x17 (5750 ns), maxlat=0x1f (7750 ns)
        intpin=a, irq=11
        powerspec 2  supports D0 D1 D2 D3  current D0
        map[10]: type Memory, range 32, base 0xd042c000, size 14, enabled
pcib5: requested memory range 0xd042c000-0xd042ffff: good
        map[14]: type I/O Port, range 32, base 0xc000, size  8, enabled
pcib5: requested I/O range 0xc000-0xc0ff: in range
pcib5: slot 0 INTA routed to irq 16
found-> vendor=0x11ab, dev=0x4320, revid=0x13
        domain=0, bus=5, slot=1, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords)
        lattimer=0x60 (2880 ns), mingnt=0x17 (5750 ns), maxlat=0x1f (7750 ns)
        intpin=a, irq=12
        powerspec 2  supports D0 D1 D2 D3  current D0
        map[10]: type Memory, range 32, base 0xd0420000, size 14, enabled
pcib5: requested memory range 0xd0420000-0xd0423fff: good
        map[14]: type I/O Port, range 32, base 0xc400, size  8, enabled
pcib5: requested I/O range 0xc400-0xc4ff: in range
pcib5: slot 1 INTA routed to irq 17
found-> vendor=0x11ab, dev=0x4320, revid=0x13
        domain=0, bus=5, slot=2, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords)
        lattimer=0x60 (2880 ns), mingnt=0x17 (5750 ns), maxlat=0x1f (7750 ns)
        intpin=a, irq=5
        powerspec 2  supports D0 D1 D2 D3  current D0
        map[10]: type Memory, range 32, base 0xd0424000, size 14, enabled
pcib5: requested memory range 0xd0424000-0xd0427fff: good
        map[14]: type I/O Port, range 32, base 0xc800, size  8, enabled
pcib5: requested I/O range 0xc800-0xc8ff: in range
pcib5: slot 2 INTA routed to irq 18
found-> vendor=0x11ab, dev=0x4320, revid=0x13
        domain=0, bus=5, slot=3, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords)
        lattimer=0x60 (2880 ns), mingnt=0x17 (5750 ns), maxlat=0x1f (7750 ns)
        intpin=a, irq=10
        powerspec 2  supports D0 D1 D2 D3  current D0
        map[10]: type Memory, range 32, base 0xd0428000, size 14, enabled
pcib5: requested memory range 0xd0428000-0xd042bfff: good
        map[14]: type I/O Port, range 32, base 0xcc00, size  8, enabled
pcib5: requested I/O range 0xcc00-0xccff: in range
pcib5: slot 3 INTA routed to irq 19
found-> vendor=0x177d, dev=0x0003, revid=0x00
        domain=0, bus=5, slot=4, func=0
        class=10-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords)
        lattimer=0x60 (2880 ns), mingnt=0x40 (16000 ns), maxlat=0x40 (16000 ns)
        intpin=a, irq=11
        powerspec 2  supports D0 D3  current D0
        MSI supports 1 message, 64 bit
        map[10]: type I/O Port, range 32, base 0xd000, size  8, enabled
pcib5: requested I/O range 0xd000-0xd0ff: in range
        map[18]: type I/O Port, range 32, base 0xd400, size  8, enabled
pcib5: requested I/O range 0xd400-0xd4ff: in range
pcib5: slot 4 INTA routed to irq 20
skc0: <marvell gigabit="" ethernet="">port 0xc000-0xc0ff mem 0xd042c000-0xd042ffff irq 16 at device 0.0 on pci5
skc0: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xd042c000
skc0: interrupt moderation is 100 us
skc0: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
skc0: chip ver  = 0xb1
skc0: chip rev  = 0x09
skc0: SK_EPROM0 = 0x10
skc0: SRAM size = 0x010000
sk0: <marvell semiconductor,="" inc.="" yukon="">on skc0
sk0: bpf attached
miibus4: <mii bus="">on sk0
e1000phy4: <marvell 88e1011="" gigabit="" phy="">PHY 0 on miibus4
e1000phy4:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-masteo
skc0: [MPSAFE]
skc0: [ITHREAD]
skc1: <marvell gigabit="" ethernet="">port 0xc400-0xc4ff mem 0xd0420000-0xd0423fff irq 17 at device 1.0 on pci5
skc1: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xd0420000
skc1: interrupt moderation is 100 us
skc1: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
skc1: chip ver  = 0xb1
skc1: chip rev  = 0x09
skc1: SK_EPROM0 = 0x10
skc1: SRAM size = 0x010000
sk1: <marvell semiconductor,="" inc.="" yukon="">on skc1
sk1: bpf attached
miibus5: <mii bus="">on sk1
e1000phy5: <marvell 88e1011="" gigabit="" phy="">PHY 0 on miibus5
e1000phy5:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-masteo
ioapic0: routing intpin 17 (PCI IRQ 17) to lapic 0 vector 56
skc1: [MPSAFE]
skc1: [ITHREAD]
skc2: <marvell gigabit="" ethernet="">port 0xc800-0xc8ff mem 0xd0424000-0xd0427fff irq 18 at device 2.0 on pci5
skc2: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xd0424000
skc2: interrupt moderation is 100 us
skc2: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
skc2: chip ver  = 0xb1
skc2: chip rev  = 0x09
skc2: SK_EPROM0 = 0x10
skc2: SRAM size = 0x010000
sk2: <marvell semiconductor,="" inc.="" yukon="">on skc2
sk2: bpf attached
miibus6: <mii bus="">on sk2
e1000phy6: <marvell 88e1011="" gigabit="" phy="">PHY 0 on miibus6
e1000phy6:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-masteo
skc2: [MPSAFE]
skc2: [ITHREAD]
skc3: <marvell gigabit="" ethernet="">port 0xcc00-0xccff mem 0xd0428000-0xd042bfff irq 19 at device 3.0 on pci5
skc3: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xd0428000
skc3: interrupt moderation is 100 us
skc3: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
skc3: chip ver  = 0xb1
skc3: chip rev  = 0x09
skc3: SK_EPROM0 = 0x10
skc3: SRAM size = 0x010000
sk3: <marvell semiconductor,="" inc.="" yukon="">on skc3
sk3: bpf attached
miibus7: <mii bus="">on sk3
e1000phy7: <marvell 88e1011="" gigabit="" phy="">PHY 0 on miibus7
e1000phy7:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-masteo
skc3: [MPSAFE]
skc3: [ITHREAD]
pci5: <encrypt decrypt,="" network="" computer="" crypto="">at device 4.0 (no driver attached)
isab0: <pci-isa bridge="">at device 31.0 on pci0
isa0: <isa bus="">on isab0
atapci0: <intel ich6="" udma100="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 31.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xf000
ata0: <ata channel="">at channel 0 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=50
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=50 devices=0x3
ioapic0: routing intpin 14 (ISA IRQ 14) to lapic 0 vector 57
ata0: [MPSAFE]
ata0: [ITHREAD]
ata1: <ata channel="">at channel 1 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=00 ostat0=ff ostat1=ff
ioapic0: routing intpin 15 (ISA IRQ 15) to lapic 0 vector 58
ata1: [MPSAFE]
ata1: [ITHREAD]
pci0: <serial bus,="" smbus="">at device 31.3 (no driver attached)
cpu0 on motherboard
est0: <enhanced speedstep="" frequency="" control="">on cpu0
p4tcc0: <cpu frequency="" thermal="" control="">on cpu0
ex_isa_identify()
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
ahc_isa_probe 12: ioport 0xcc00 alloc failed
ahc_isa_probe 14: ioport 0xec00 alloc failed
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
pnpbios: 14 devices, largest 92 bytes
PNP0200: adding dma mask 0x10
PNP0200: adding io range 0-0xf, size=0x10, align=0
PNP0200: adding io range 0x81-0x83, size=0x3, align=0
PNP0200: adding io range 0x87-0x87, size=0x1, align=0
PNP0200: adding io range 0x89-0x8b, size=0x3, align=0
PNP0200: adding io range 0x8f-0x91, size=0x3, align=0
PNP0200: adding io range 0xc0-0xdf, size=0x20, align=0
pnpbios: handle 1 device ID PNP0200 (0002d041)
PNP0100: adding irq mask 0x1
PNP0100: adding io range 0x40-0x43, size=0x4, align=0
pnpbios: handle 2 device ID PNP0100 (0001d041)
PNP0b00: adding irq mask 0x100
PNP0b00: adding io range 0x70-0x71, size=0x2, align=0
pnpbios: handle 3 device ID PNP0b00 (000bd041)
PNP0303: adding irq mask 0x2
PNP0303: adding io range 0x60-0x60, size=0x1, align=0
PNP0303: adding io range 0x64-0x64, size=0x1, align=0
pnpbios: handle 4 device ID PNP0303 (0303d041)
PNP0800: adding io range 0x61-0x61, size=0x1, align=0
pnpbios: handle 5 device ID PNP0800 (0008d041)
PNP0c04: adding irq mask 0x2000
PNP0c04: adding io range 0xf0-0xff, size=0x10, align=0
pnpbios: handle 6 device ID PNP0c04 (040cd041)
INT0800: adding fixed memory32 range 0xffb80000-0xffbfffff, size=0x80000
pnpbios: handle 7 device ID INT0800 (0008d425)
PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000
PNP0c01: adding fixed memory32 range 0xffb00000-0xffb7ffff, size=0x80000
PNP0c01: adding fixed memory32 range 0xfff00000-0xffffffff, size=0x100000
PNP0c01: adding fixed memory32 range 0xfec00000-0xfec0ffff, size=0x10000
PNP0c01: adding fixed memory32 range 0xfee00000-0xfee0ffff, size=0x10000
PNP0c01: adding fixed memory32 range 0x100000-0xffffff, size=0xf00000
pnpbios: handle 8 device ID PNP0c01 (010cd041)
PNP0c02: adding fixed memory32 range 0xf0000-0xf3fff, size=0x4000
PNP0c02: adding fixed memory32 range 0xf4000-0xf7fff, size=0x4000
PNP0c02: adding fixed memory32 range 0xf8000-0xfffff, size=0x8000
PNP0c02: adding fixed memory32 range 0xce800-0xcffff, size=0x1800
pnpbios: handle 9 device ID PNP0c02 (020cd041)
PNP0a03: adding io range 0x294-0x297, size=0x4, align=0
PNP0a03: adding io range 0x4d0-0x4d1, size=0x2, align=0
PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0
PNP0a03: adding io range 0x400-0x4bf, size=0xc0, align=0
pnpbios: handle 10 device ID PNP0a03 (030ad041)
PNP0501: adding irq mask 0x10
PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0
pnpbios: handle 12 device ID PNP0501 (0105d041)
PNP0400: adding irq mask 0x80
PNP0400: adding io range 0x378-0x37f, size=0x8, align=0
PNP0400: adding io range 0x778-0x77b, size=0x4, align=0
pnpbios: handle 13 device ID PNP0400 (0004d041)
PNP0501: adding irq mask 0x8
PNP0501: adding io range 0x2f8-0x2ff, size=0x8, align=0
pnpbios: handle 15 device ID PNP0501 (0105d041)
isa_probe_children: disabling PnP devices
pmtimer0 on isa0
atrtc0: <at realtime="" clock="">at port 0x70-0x71 irq 8 pnpid PNP0b00 on isa0
atrtc0: registered as a time-of-day clock (resolution 1000000us)
atkbdc0: <keyboard controller="" (i8042)="">at port 0x60,0x64 irq 1 pnpid PNP0303 on isa0
atkbd0: <at keyboard="">irq 1 on atkbdc0
kbd0 at atkbd0
kbd0: atkbd0, generic (0), config:0x0, flags:0x3f0000
ioapic0: routing intpin 1 (ISA IRQ 1) to lapic 0 vector 59
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: unable to allocate IRQ
unknown: <at real="" time="" clock="">failed to probe at port 0x61 pnpid PNP0800 on isa0
unknown: <at real="" time="" clock="">failed to probe at iomem 0xffb80000-0xffbfffff pnpid INT0800 on isa0
unknown: <pnp0c01>can't assign resources (memory)
unknown: <pnp0c01>at iomem 0-0x9ffff pnpid PNP0c01 on isa0
uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 pnpid PNP0501 on isa0
ioapic0: routing intpin 4 (ISA IRQ 4) to lapic 0 vector 60
uart0: [FILTER]
uart0: fast interrupt
uart0: console (115200,n,8,1)
ppc0: using extended I/O port range
ppc0: SPP
ppc0: <standard parallel="" printer="" port="">at port 0x378-0x37f,0x778-0x77b irq 7 pnpid PNP0400 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ioapic0: routing intpin 7 (ISA IRQ 7) to lapic 0 vector 61
ppc0: [MPSAFE]
ppc0: [ITHREAD]
ppbus0: <parallel port="" bus="">on ppc0
plip0: <plip network="" interface="">on ppbus0
plip0: bpf attached
plip0: [MPSAFE]
plip0: [ITHREAD]
lpt0: <printer>on ppbus0
lpt0: [MPSAFE]
lpt0: [ITHREAD]
lpt0: Interrupt-driven port
ppi0: <parallel i="" o="">on ppbus0
uart1: <16550 or compatible> at port 0x2f8-0x2ff irq 3 pnpid PNP0501 on isa0
ioapic0: routing intpin 3 (ISA IRQ 3) to lapic 0 vector 62
uart1: [FILTER]
uart1: fast interrupt
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
atrtc: atrtc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sc: sc0 already exists; skipping it
uart: uart0 already exists; skipping it
uart: uart1 already exists; skipping it
isa_probe_children: probing non-PnP devices
orm0: <isa option="" rom="">at iomem 0xc0000-0xce7ff pnpid ORM0000 on isa0
sc0: <system console="">at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: scteken (teken terminal)
vga0: <generic isa="" vga="">at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
isa_probe_children: probing PnP devices
unknown: <pnp0c01>can't assign resources (memory)
unknown: <pnp0c01>at iomem 0-0x9ffff pnpid PNP0c01 on isa0
Device configuration finished.
procfs registered
lapic: Divisor 2, Frequency 50002125 Hz
Timecounter "TSC" frequency 1600067815 Hz quality 800
Timecounters tick every 1.000 msec
crypto: <crypto device="">vlan: initialized, using hash tables with chaining
IPsec: Initialized Security Association Processing.
enc0: bpf attached
pflog0: bpf attached
lo0: bpf attached
pfsync0: bpf attached
hptrr: no controller detected.
ata0: Identifying devices: 00000003
ata0: New devices: 00000003
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 480Mbps High Speed USB v2.0
ata0-slave: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=40 wire
ata0-master: pio=PIO4 wdma=UNSUPPORTED udma=UNSUPPORTED cable=40 wire
ad0: setting PIO4
ad0: 244MB <hitachi xx.v.3.3.0.0="" rev="" 0.00="">at ata0-master PIO4 
ad0: 500400 sectors [695C/15H/48S] 1 sectors/interrupt 1 depth queue
GEOM: new disk ad0
ugen0.1: <intel>at usbus0
ugen1.1: <intel>at usbus1
ugen2.1: <intel>at usbus2
ugen3.1: <intel>at usbus3
ugen4.1: <intel>at usbus4
ad0: Intel check1 failed
uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
can't re-use a leaf (%parent)!
uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
can't re-use a leaf (%parent)!
uhub2: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus2
can't re-use a leaf (%parent)!
uhub3: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus3
can't re-use a leaf (%parent)!
uhub4: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus4
ad0: Adaptec check1 failed
ad0: LSI (v3) check1 failed
ad0: LSI (v2) check1 failed
ad0: FreeBSD check1 failed
ata0: DMA limited to UDMA33, controller found non-ATA66 cable
ad1: setting UDMA33
ad1: 0MB <toshiba mk1031gas="" aa204a="">at ata0-slave UDMA33 
ad1: 0 sectors [0C/16H/63S] 16 sectors/interrupt 1 depth queue
ad1: FAILURE - READ_DMA48 status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=18446744073709551613
ad1: Intel read metadata failed
ad1: FAILURE - READ_DMA status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=18446744073709551599
ad1: Adaptec read metadata failed
ad1: FAILURE - READ_DMA status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=18446744073709551612
ad1: LSI (v3) read metadata failed
ad1: FAILURE - READ_DMA status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=18446744073709551615
ad1: LSI (v2) read metadata failed
ad1: FAILURE - READ_DMA status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=18446744073709551615
ad1: DDF read metadata failed
ad1: FAILURE - READ_DMA48 status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=18446744073709551553
ad1: FreeBSD read metadata failed
ata1: Identifying devices: 00000000
ata1: New devices: 00000000
ATA PseudoRAID loaded
GEOM: new disk ad1
Root mount waiting for: usbus4 usbus3 usbus2 usbus1 usbus0
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
Root mount waiting for: usbus4
Root mount waiting for: usbus4
Root mount waiting for: usbus4
uhub4: 8 ports with 8 removable, self powered
Trying to mount root from ufs:/dev/ad0s1a
ROOT MOUNT ERROR: 
If you have invalid mount options, reboot, and first try the following from
the loader prompt:

     set vfs.root.mountfrom.options=rw

and then remove invalid mount options from /etc/fstab.

Loader variables:
vfs.root.mountfrom=ufs:/dev/ad0s1a
vfs.root.mountfrom.options=rw

Manual root filesystem specification:
  <fstype>:<device>Mount <device>using filesystem <fstype>eg. ufs:/dev/da0s1a
                       eg. cd9660:/dev/acd0
                       This is equivalent to: mount -t cd9660 /dev/acd0 /

  ?                  List valid disk boot devices
  <empty line="">Abort manual input

mountroot></empty></fstype></device></device></fstype></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></toshiba></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></hitachi></crypto></pnp0c01></pnp0c01></generic></system></isa></parallel></printer></plip></parallel></standard></pnp0c01></pnp0c01></at></at></at></keyboard></at></cpu></enhanced></serial></ata></ata></intel></isa></pci-isa></encrypt></marvell></mii></marvell></marvell></marvell></mii></marvell></marvell></marvell></mii></marvell></marvell></marvell></mii></marvell></marvell></pci></mptable></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></marvell></mii></marvell></marvell></pci></mptable></marvell></mii></marvell></marvell></pci></mptable></marvell></mii></marvell></marvell></pci></mptable></marvell></mii></marvell></marvell></pci></mptable></intel></vga-compatible></pci></mptable></software></entropy>_</null></crypto></memory></version></oem00000></est,tm2></fpu,vme,de,pse,tsc,msr,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,tm,pbe> 
``` _I didn't expect that it could be a matter of the disk size… This is interesting. Let's see if can find out anything  :)_

stephenw10

It's not so much the size of the disk as the geometry. That's the reason you have to set the heads to 2 to boot larger CF cards. Some bug in the BIOS code calculates something wrong.

ad1: 0MB <toshiba mk1031gas="" aa204a=""> at ata0-slave UDMA33 
ad1: 0 sectors [0C/16H/63S] 16 sectors/interrupt 1 depth queue</toshiba>

0 cyclinders looks bad! ;) That's then followed by loads of 'NID not found' errors which indicate trying to read some part of the disk that doesn't exist.

Try setting it as master. Try removing the CF card.

Steve

chpalmer

Try setting it as master. Try removing the CF card.

Thats how I run my x550e here…

zero

Too bad… same results when using the HDD as master.


ad0: 0MB <toshiba mk1031gas="" aa204a="">at ata0-master UDMA33 
ad0: 0 sectors [0C/16H/63S] 16 sectors/interrupt 1 depth queue</toshiba>

I'll check if I can find another HDD and come up with other/better results ;)

stephenw10

Have you been through the bios setup to allow it to autodetect the disk? What geometry does the bios report?

An 80GB drive has also been confirmed to work without any special measures:
http://forum.pfsense.org/index.php/topic,56234.msg304473.html#msg304473

I think perhaps only the smaller drives are causing trouble and you should try just detecting the drive. Remove the CF card, set the drive as master, don't use verbose mode.

Steve

zero

The machine is alive 8)
I had to manually set the HDD mode to "LBA" in the bios. Now everything works fine :)
Thanks for hints and support!

stephenw10

Excellent. :)
To help anyone else could you detail what settings you ended up with that worked?
CF card installed, master or slave, verbose mode etc.

Steve

zero

The following worked for my setup:

Remove CF card
Set HDD as master
In bios: Select the HDD in "Standard CMOS Features" by pressing enter and set "Access Mode" to "LBA", the rest is set to "Auto"

That's it. PfSense starts in standard and verbose mode.