How configure?
-
It appeared to me in some tests the written RL0 RL1 and not only usb0 and USB1.
For the output of the command pciconf-l I have to wait but as soon as I can write it …
also with both the live and installed on hd the problem is the same (I can not get over the LAN with the pfsense web gui) and also interfaces "accidentally" are called usb0 and usb1 but sometimes rl0 and rl1 but whatever in any case there can not access the web gui -
No nfe0 interface then? Is the on-board NIC enabled?
Steve
-
Hi, yes the NIC is enabled on the bios….
and the outputo of command PCICONF -L Returns too much data I am sending a photo taken with my cell phone......:'( :'( :'( :'(
-
OK, so I see rl0 and rl1. I also see none2 which implies there is a none0 and none1 also.
Can you list those 'none' devices.
[2.1.1-PRERELEASE][root@pfsense.localdomain]/root(4): pciconf -lv | grep none none0@pci0:0:31:3: class=0x0c0500 card=0x27da8086 chip=0x27da8086 rev=0x01 hdr=0x00Steve
-
i post this!
-
another screen shot
-
Ok, well those 3 devices are part of the Nvidia chipset on that board. The SMBus and Audio components are not relevant. The memory controller is clearly working to some extent anyway.
The on board network card is not listed. I would expect to see it as nfe0 or if not then something at least listed as class 0x020000, network controller.Steve
-
The on board network card is not listed. I would expect to see it as nfe0 or if not then something at least listed as class 0x020000, network controller.
Well, I can pretty clearly see nfe0 on this screenshot
-
Did you see something like this when you Boot you pfSense ?
-
If you use the "option" 4 and "Reset to Factory defaults" what do you get listed as "Valid Interfaces" ?
Just curious, from which Country are you ? (do you speak Spanish ?)
-
Well, I can pretty clearly see nfe0 on this screenshot.
Doh! ::) Not enough/too much coffee.
Ok, so assign nfe0 to LAN instead of your Realtek NICs that seem to be so flaky.
Steve
-
Thank you so much but I can not understand the last message that I can bring to the speech that I can not load the web gui on the LAN PC with pfSense.
And then, still in its availability, how should I proceed?
We thank the greeting waiting for new posts.
Leonardo_T ;) -
You do not need any webgui, you can assign if from console.
-
Well well well i can access to web gui….
i connect the la on NFE0 e i have use restore default setting....but, how configure the firewall to navigate?
at the same i can't!!thnak's for your time !
-
How have you configured WAN? I assume rl0 or rl1. What is your WAN connected to?
Steve
-
Hi, i'm sorry but i'm Italian and i don't speak Espanol…
i use google translate for write this post...the wan assumed RL0 and this result connected on Alice (ISP) the connection is DHCP from router... no pppoe or ppoatm.....
-
OK so you are using rl0 for WAN.
Is it receiving an IP address from your router?There as an Italian subforum you might like to use:
https://forum.pfsense.org/index.php?board=8.0Steve
-
I ,i don't receive ip from router…
but when i change the ip of lan after i can't access at the web gui of pfSense him accept only 192.168.1.1 (default) thi is the same of the router!!!I give up, I found a rock too big for me and I do not understand anything
Thank you so much for your interest in me, if it had not been for you so many things I would not have understood.
-
No problem. Sorry I couldn't help more. :-\
I you try again you might get more useful answers in the italian forum.
Steve
