Upgrade to 2.1.2: Stuck on 2.1
-
Provide the whole upgrade log. The part being quoted isn't the problem.
We tested the 4GB version more than others, as it's the most common one in use.
-
http://pastebin.com/YX8vK7C1
-
Here's your problem:
gpart set -a active -i 1 ad0 gpart: table 'ad0' is corrupt: Operation not permittedTry this:
gpart bootcode -b /boot/mbr ad0Then try the upgrade again.
-
Thanks, jimp. Missed that perm issue in the log.
Unfortunately, running "gpart bootcode -b /boot/mbr ad0" also results in the exact same error, noting that ad0 is corrupt.
-
I have the exact same issue with same error in my upgrade log on a 2g install on an Alix box.
I also had the issue on a 4g install but I opted to flash a new image and swap cards. The 2g box though is 4 hours round trip away so I would love to fix the issue and update remotely.
I also had another 4g box that updated just fine. So, 2 out of 3 are broken and would not update with autoupdate or manual update.
-
Other things to try:
Set the boot slice on Diagnostics > NanoBSD, see if it actually changes.
or
gpart recover ad0or
sysctl kern.geom.debugflags=16 boot0cfg -v -s 1 ad0 fdisk -a /dev/ad0 sysctl kern.geom.debugflags=0(For fdisk make sure to specify the values it asks and press 'y' to confirm!)
We have yet to be able to reproduce this effectively, but several people have hit it. It would be helpful to know some more about the original setup that failed. Was it your own CF or did it come with the device? Had it ever been upgraded before, and if so how many times? What was its original version of pfSense on that CF card before upgrading?
-
Slice does not change; nor I can copy ad0s2 -> ad0s1.
-
gpart bootcode -b /boot/mbr ad0 gpart: table 'ad0' is corrupt: Operation not permittedgpart recover ad0 gpart: recovering 'ad0' failed: Function not implemented -
fdisk -a /dev/ad0I get an Intput/Output error.
This is compact flash card. It was installed as 2.0 and then upgraded to 2.0.3 and later 2.1.
-
In my case I had pfSense nanobsd v1.2.3 upgraded to v2.0, that one upgraded to v2.1 - all of them upgraded OK. Now when I wanted to upgrade to v2.1.2, It seems corrupted. I'm preparing a fresly flashed CF card with config already put in.
-
I am having the same issue. Hopefully my situation will help shed some light.
-
I have upgraded at least two other NanoBSD 4G (ALIX) system without issue.
-
Today I am upgrading three identical boxes - ALIX boards running 4G CF card
-
One existing install was already 2.1 and I successfully upgraded to 2.1.2
-
The other two were at 2.0.3 and I successfully upgraded to 2.1, but they are both now stuck on 2.1 after auto-upgrade and manual upgrade attempts.
-
-
Also a side note, I'm not on Alix, but on a Jetway JNF99 with 5 intel nics, Atom CPU and 4GB of RAM, i386 build. The new CF card will carry a 64-bit version this time.
-
If you're getting an "i/o error" or "device not configured", reboot and try again. At least for the "i/o error" it seems to lean more toward maybe a bad CF but it's still tough to say for sure.
Also worth a try:
sysctl kern.geom.debugflags=16 fdisk -B -b /boot/boot0 ad0 -
I'm in the same boat with 40 plus devices scattered across 4 provinces. I actually haven't managed to get a single one to upgrade except the 3 in our local offices that I performed a clean install on, 2G and 4G, current versions 2.03 and 2.1 on all remotes attempting auto upgrade and manual firmware uploads. Not sure what to do, since I don't want to risk chopping them up and losing remote connectivity. I don't own a helicopter to get around that quickly ;D
All Alix boards. Errors in the upgrade log
fdisk: invalid fdisk partition table found
bsdlabel: /dev/ad0s3: no valid label found
bsdlabel: /dev/ad0s3: no valid label found
bsdlabel: /dev/ad0s3: no valid label found
tar: Failed to set default locale
tar: Failed to set default locale
shutdown: [pid 24752] -
I have same issue apparently. No answer. Here's my log:
NanoBSD Firmware upgrade in progress... Installing /root/latest.tgz. SLICE 1 OLDSLICE 2 TOFLASH ad0s1 COMPLETE_PATH ad0s1a GLABEL_SLICE pfSense0 Sun Apr 13 02:37:42 EDT 2014 total 8 dr-xr-xr-x 7 root wheel 512B Apr 12 15:03 . drwxr-xr-x 26 root wheel 1.0k Apr 12 15:03 .. crw-r----- 1 root operator 0, 56 Apr 12 15:03 ad0 crw-r----- 1 root operator 0, 57 Apr 12 15:03 ad0s1 crw-r----- 1 root operator 0, 60 Apr 12 15:03 ad0s1a crw-r----- 1 root operator 0, 58 Apr 12 15:03 ad0s2 crw-r----- 1 root operator 0, 61 Apr 12 15:03 ad0s2a crw-r----- 1 root operator 0, 59 Apr 12 15:03 ad0s3 crw------- 1 root operator 0, 28 Apr 12 15:03 ata crw------- 1 root wheel 0, 11 Apr 13 01:29 bpf lrwxr-xr-x 1 root wheel 3B Apr 12 15:03 bpf0 -> bpf crw------- 1 root tty 0, 4 Apr 13 02:37 console crw-rw-rw- 1 root wheel 0, 44 Apr 12 15:03 crypto crw-rw-rw- 1 root wheel 0, 10 Apr 12 15:03 ctty crw-rw---- 1 uucp dialer 0, 35 Apr 12 15:03 cuau0 crw-rw---- 1 uucp dialer 0, 36 Apr 12 15:03 cuau0.init crw-rw---- 1 uucp dialer 0, 37 Apr 12 15:03 cuau0.lock crw-rw---- 1 uucp dialer 0, 41 Apr 12 15:03 cuau1 crw-rw---- 1 uucp dialer 0, 42 Apr 12 15:03 cuau1.init crw-rw---- 1 uucp dialer 0, 43 Apr 12 15:03 cuau1.lock crw------- 1 root wheel 0, 5 Apr 12 15:03 devctl cr-------- 1 root wheel 0, 54 Apr 12 15:03 devstat dr-xr-xr-x 2 root wheel 512B Apr 12 15:03 fd crw------- 1 root wheel 0, 13 Apr 12 15:03 fido crw-r----- 1 root operator 0, 3 Apr 12 15:03 geom.ctl crw------- 1 root wheel 0, 23 Apr 12 15:03 io crw------- 1 root wheel 0, 8 Apr 12 15:03 klog crw-r----- 1 root kmem 0, 15 Apr 12 15:03 kmem dr-xr-xr-x 2 root wheel 512B Apr 12 15:03 led crw-r----- 1 root operator 0, 62 Apr 12 15:03 md0 crw-r----- 1 root operator 0, 66 Apr 12 15:03 md1 crw------- 1 root wheel 0, 47 Apr 12 15:03 mdctl crw-r----- 1 root kmem 0, 14 Apr 12 15:03 mem crw------- 1 root kmem 0, 16 Apr 12 15:03 nfslock crw-rw-rw- 1 root wheel 0, 25 Apr 13 02:37 null crw-r--r-- 1 root wheel 0, 27 Apr 12 15:03 pci crw-rw---- 1 root proxy 0, 45 Apr 12 15:03 pf crw-rw-rw- 1 root wheel 0, 9 Apr 12 15:03 ptmx crw-rw-rw- 1 root wheel 0, 6 Apr 12 15:03 random crw------- 1 root wheel 0, 24 Apr 12 15:03 speaker lrwxr-xr-x 1 root wheel 4B Apr 12 15:03 stderr -> fd/2 lrwxr-xr-x 1 root wheel 4B Apr 12 15:03 stdin -> fd/0 lrwxr-xr-x 1 root wheel 4B Apr 12 15:03 stdout -> fd/1 crw------- 1 root wheel 0, 32 Apr 12 15:03 ttyu0 crw------- 1 root wheel 0, 33 Apr 12 15:03 ttyu0.init crw------- 1 root wheel 0, 34 Apr 12 15:03 ttyu0.lock crw------- 1 root wheel 0, 38 Apr 12 15:03 ttyu1 crw------- 1 root wheel 0, 39 Apr 12 15:03 ttyu1.init crw------- 1 root wheel 0, 40 Apr 12 15:03 ttyu1.lock crw------- 1 uucp dialer 0, 73 Apr 12 15:04 tun1 dr-xr-xr-x 2 root wheel 512B Apr 12 15:03 ufs dr-xr-xr-x 2 root wheel 512B Apr 12 15:03 ufsid lrwxr-xr-x 1 root wheel 9B Apr 12 15:03 ugen0.1 -> usb/0.1.0 lrwxr-xr-x 1 root wheel 9B Apr 12 15:03 ugen1.1 -> usb/1.1.0 lrwxr-xr-x 1 root wheel 6B Apr 12 15:03 urandom -> random dr-xr-xr-x 2 root wheel 512B Apr 12 15:03 usb crw-r--r-- 1 root operator 0, 46 Apr 12 15:03 usbctl crw------- 1 root operator 0, 55 Apr 12 15:03 xpt0 crw-rw-rw- 1 root wheel 0, 26 Apr 12 15:03 zero -rw-r--r-- 1 root wheel 76M Apr 13 02:34 /root/latest.tgz MD5 (/root/latest.tgz) = b914649dd6be90a461a99615c07882c3 /dev/ufs/pfSense1 on / (ufs, local, noatime, synchronous) devfs on /dev (devfs, local) /dev/ufs/cf on /cf (ufs, local, noatime, synchronous) /dev/md0 on /tmp (ufs, local) /dev/md1 on /var (ufs, local) devfs on /var/dhcpd/dev (devfs, local) last pid: 52248; load averages: 3.09, 1.78, 1.20 up 0+11:34:50 02:38:14 67 processes: 7 running, 60 sleeping Mem: 92M Active, 50M Inact, 74M Wired, 6780K Cache, 33M Buf, 7052K Free Swap: PID USERNAME THR PRI NICE SIZE RES STATE TIME WCPU COMMAND 92215 root 1 76 0 40308K 20156K accept 4:21 0.00% php 86955 root 1 76 0 26484K 15784K accept 2:37 0.00% php 41671 root 1 44 0 8004K 4984K kqread 1:04 0.00% lighttpd 93099 root 1 76 20 3644K 1332K piperd 0:20 0.00% sh 292 root 1 76 20 3352K 1112K kqread 0:15 0.00% check_reload_status 45599 nobody 1 44 0 5512K 2316K select 0:12 0.00% dnsmasq 31777 root 1 44 0 3264K 1208K select 0:12 0.00% apinger 97171 root 1 44 0 3416K 1400K select 0:10 0.00% syslogd 66552 root 1 44 0 7284K 5872K select 0:07 0.00% bsnmpd 30425 root 21 44 0 21400K 3996K ucond 0:05 0.00% filterdns 78170 root 1 64 20 6280K 6300K select 0:05 0.00% ntpd 52603 dhcpd 1 44 0 11456K 7584K select 0:05 0.00% dhcpd 25251 root 1 44 0 3264K 848K piperd 0:03 0.00% logger 90659 proxy 1 64 20 10356K 5928K kqread 0:03 0.00% squid 25151 root 1 44 0 5868K 1916K bpf 0:02 0.00% tcpdump 61760 root 1 44 0 5952K 2324K kqread 0:01 0.00% lighttpd 72531 root 1 64 20 5432K 3224K select 0:01 0.00% openvpn 19617 root 1 44 0 5144K 1544K select 0:01 0.00% hostapd NanoBSD upgrade starting dd if=/dev/zero of=/dev/ad0s1 bs=1m count=1 1+0 records in 1+0 records out 1048576 bytes transferred in 0.344171 secs (3046671 bytes/sec) /usr/bin/gzip -dc /root/latest.tgz | /bin/dd of=/dev/ad0s1 obs=64k 3844449+0 records in 30034+1 records out 1968357888 bytes transferred in 394.695594 secs (4987028 bytes/sec) After upgrade fdisk/bsdlabel /sbin/fsck_ufs -y /dev/ad0s1a ** /dev/ad0s1a ** Last Mounted on /tmp/netgatemnt ** Phase 1 - Check Blocks and Sizes ** Phase 2 - Check Pathnames ** Phase 3 - Check Connectivity ** Phase 4 - Check Reference Counts ** Phase 5 - Check Cyl groups 5506 files, 317470 used, 3462558 free (542 frags, 432752 blocks, 0.0% fragmentation) ***** FILE SYSTEM IS CLEAN ***** /sbin/tunefs -L pfSense0 /dev/ad0s1a Checking for post_upgrade_command... Found post_upgrade_command, executing (pfSense0)... tar: Failed to set default locale Checking for /tmp/pfSense0/tmp/post_upgrade_command.php... Running /tmp/pfSense0/tmp/post_upgrade_command.php pfSense0 Adding serial port settings (/tmp/pfSense0)... Reading /tmp/pfSense0/boot/loader.conf... /dev/ufs/pfSense0 / ufs ro,sync,noatime 1 1 /dev/ufs/cf /cf ufs ro,sync,noatime 1 1 gpart set -a active -i 1 ad0 gpart: table 'ad0' is corrupt: Operation not permitted /usr/sbin/boot0cfg -s 1 -v /dev/ad0 # flag start chs type end chs offset size 1 0x00 0: 1: 1 0xa5 751: 15:63 63 3854529 2 0x80 752: 1: 1 0xa5 479: 15:63 3854655 3854529 3 0x00 480: 0: 1 0xa5 581: 15:63 7709184 102816 version=2.0 drive=0x80 mask=0x3 ticks=182 bell=# (0x23) options=packet,update,nosetdrv volume serial ID 9090-9090 default_selection=F1 (Slice 1) Sun Apr 13 02:48:27 EDT 2014 NanoBSD Firmware upgrade is complete. Rebooting in 10 seconds. File list: /tmp/pfSense0 /tmp/pfSense0/.snap /tmp/pfSense0/COPYRIGHT /tmp/pfSense0/bin /tmp/pfSense0/bin/cat /tmp/pfSense0/bin/chflags /tmp/pfSense0/bin/chmod /tmp/pfSense0/bin/cp /tmp/pfSense0/bin/csh /tmp/pfSense0/bin/tcsh /tmp/pfSense0/bin/date /tmp/pfSense0/bin/dd /tmp/pfSense0/bin/df /tmp/pfSense0/bin/domainname /tmp/pfSense0/bin/echo /tmp/pfSense0/bin/expr /tmp/pfSense0/bin/hostname /tmp/pfSense0/bin/kenv /tmp/pfSense0/bin/kill /tmp/pfSense0/bin/ln /tmp/pfSense0/bin/link .....a bunch more tmp files.. Misc log: fdisk: invalid fdisk partition table found bsdlabel: /dev/ad0s3: no valid label found bsdlabel: /dev/ad0s3: no valid label found bsdlabel: /dev/ad0s3: no valid label found tar: Failed to set default locale tar: Failed to set default locale shutdown: [pid 82135] fdisk/bsdlabel log: Before upgrade fdisk/bsdlabel ******* Working on device /dev/ad0 ******* parameters extracted from in-core disklabel are: cylinders=7745 heads=16 sectors/track=63 (1008 blks/cyl) Figures below won't work with BIOS for partitions not in cyl 1 parameters to be used for BIOS calculations are: cylinders=7745 heads=16 sectors/track=63 (1008 blks/cyl) Media sector size is 512 Warning: BIOS sector numbering starts with sector 1 Information from DOS bootblock is: The data for partition 1 is: sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD) start 63, size 3854529 (1882 Meg), flag 0 beg: cyl 0/ head 1/ sector 1; end: cyl 751/ head 15/ sector 63 The data for partition 2 is: sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD) start 3854655, size 3854529 (1882 Meg), flag 80 (active) beg: cyl 752/ head 1/ sector 1; end: cyl 479/ head 15/ sector 63 The data for partition 3 is: sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD) start 7709184, size 102816 (50 Meg), flag 0 beg: cyl 480/ head 0/ sector 1; end: cyl 581/ head 15/ sector 63 The data for partition 4 is: <unused># /dev/ad0s1: type: unknown disk: amnesiac label: flags: bytes/sector: 512 sectors/track: 63 tracks/cylinder: 16 sectors/cylinder: 1008 cylinders: 3813 sectors/unit: 3844449 rpm: 3600 interleave: 1 trackskew: 0 cylinderskew: 0 headswitch: 0 # milliseconds track-to-track seek: 0 # milliseconds drivedata: 0 8 partitions: # size offset fstype [fsize bsize bps/cpg] a: 3844433 16 unused 0 0 c: 3844449 0 unused 0 0 # "raw" part, don't edit # /dev/ad0s2: type: unknown disk: amnesiac label: flags: bytes/sector: 512 sectors/track: 63 tracks/cylinder: 16 sectors/cylinder: 1008 cylinders: 3813 sectors/unit: 3844449 rpm: 3600 interleave: 1 trackskew: 0 cylinderskew: 0 headswitch: 0 # milliseconds track-to-track seek: 0 # milliseconds drivedata: 0 8 partitions: # size offset fstype [fsize bsize bps/cpg] a: 3844433 16 unused 0 0 c: 3844449 0 unused 0 0 # "raw" part, don't edit --------------------------------------------------------------- ******* Working on device /dev/ad0 ******* parameters extracted from in-core disklabel are: cylinders=7745 heads=16 sectors/track=63 (1008 blks/cyl) Figures below won't work with BIOS for partitions not in cyl 1 parameters to be used for BIOS calculations are: cylinders=7745 heads=16 sectors/track=63 (1008 blks/cyl) Media sector size is 512 Warning: BIOS sector numbering starts with sector 1 Information from DOS bootblock is: The data for partition 1 is: sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD) start 63, size 3854529 (1882 Meg), flag 0 beg: cyl 0/ head 1/ sector 1; end: cyl 751/ head 15/ sector 63 The data for partition 2 is: sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD) start 3854655, size 3854529 (1882 Meg), flag 80 (active) beg: cyl 752/ head 1/ sector 1; end: cyl 479/ head 15/ sector 63 The data for partition 3 is: sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD) start 7709184, size 102816 (50 Meg), flag 0 beg: cyl 480/ head 0/ sector 1; end: cyl 581/ head 15/ sector 63 The data for partition 4 is: <unused># /dev/ad0s1: type: unknown disk: amnesiac label: flags: bytes/sector: 512 sectors/track: 63 tracks/cylinder: 16 sectors/cylinder: 1008 cylinders: 3813 sectors/unit: 3844449 rpm: 3600 interleave: 1 trackskew: 0 cylinderskew: 0 headswitch: 0 # milliseconds track-to-track seek: 0 # milliseconds drivedata: 0 8 partitions: # size offset fstype [fsize bsize bps/cpg] a: 3844433 16 unused 0 0 c: 3844449 0 unused 0 0 # "raw" part, don't edit # /dev/ad0s2: type: unknown disk: amnesiac label: flags: bytes/sector: 512 sectors/track: 63 tracks/cylinder: 16 sectors/cylinder: 1008 cylinders: 3813 sectors/unit: 3844449 rpm: 3600 interleave: 1 trackskew: 0 cylinderskew: 0 headswitch: 0 # milliseconds track-to-track seek: 0 # milliseconds drivedata: 0 8 partitions: # size offset fstype [fsize bsize bps/cpg] a: 3844433 16 unused 0 0 c: 3844449 0 unused 0 0 # "raw" part, don't edit --------------------------------------------------------------- Final upgrade fdisk/bsdlabel ******* Working on device /dev/ad0 ******* parameters extracted from in-core disklabel are: cylinders=7745 heads=16 sectors/track=63 (1008 blks/cyl) Figures below won't work with BIOS for partitions not in cyl 1 parameters to be used for BIOS calculations are: cylinders=7745 heads=16 sectors/track=63 (1008 blks/cyl) Media sector size is 512 Warning: BIOS sector numbering starts with sector 1 Information from DOS bootblock is: The data for partition 1 is: sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD) start 63, size 3854529 (1882 Meg), flag 0 beg: cyl 0/ head 1/ sector 1; end: cyl 751/ head 15/ sector 63 The data for partition 2 is: sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD) start 3854655, size 3854529 (1882 Meg), flag 80 (active) beg: cyl 752/ head 1/ sector 1; end: cyl 479/ head 15/ sector 63 The data for partition 3 is: sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD) start 7709184, size 102816 (50 Meg), flag 0 beg: cyl 480/ head 0/ sector 1; end: cyl 581/ head 15/ sector 63 The data for partition 4 is: <unused># /dev/ad0s1: type: unknown disk: amnesiac label: flags: bytes/sector: 512 sectors/track: 63 tracks/cylinder: 16 sectors/cylinder: 1008 cylinders: 3813 sectors/unit: 3844449 rpm: 3600 interleave: 1 trackskew: 0 cylinderskew: 0 headswitch: 0 # milliseconds track-to-track seek: 0 # milliseconds drivedata: 0 8 partitions: # size offset fstype [fsize bsize bps/cpg] a: 3844433 16 unused 0 0 c: 3844449 0 unused 0 0 # "raw" part, don't edit # /dev/ad0s2: type: unknown disk: amnesiac label: flags: bytes/sector: 512 sectors/track: 63 tracks/cylinder: 16 sectors/cylinder: 1008 cylinders: 3813 sectors/unit: 3844449 rpm: 3600 interleave: 1 trackskew: 0 cylinderskew: 0 headswitch: 0 # milliseconds track-to-track seek: 0 # milliseconds drivedata: 0 8 partitions: # size offset fstype [fsize bsize bps/cpg] a: 3844433 16 unused 0 0 c: 3844449 0 unused 0 0 # "raw" part, don't edit ---------------------------------------------------------------</unused></unused></unused> -
I'm in the same boat with 40 plus devices scattered across 4 provinces. I actually haven't managed to get a single one to upgrade except the 3 in our local offices that I performed a clean install on, 2G and 4G, current versions 2.03 and 2.1 on all remotes attempting auto upgrade and manual firmware uploads. Not sure what to do, since I don't want to risk chopping them up and losing remote connectivity. I don't own a helicopter to get around that quickly ;D
All Alix boards. Errors in the upgrade log
fdisk: invalid fdisk partition table found
bsdlabel: /dev/ad0s3: no valid label found
bsdlabel: /dev/ad0s3: no valid label found
bsdlabel: /dev/ad0s3: no valid label found
tar: Failed to set default locale
tar: Failed to set default locale
shutdown: [pid 24752]I hear ya about all those remote devices and no time to travel there if there is a problem. For me if there is a risk of breaking it at a remote site I would send them another firewall box and tell them to swap it when time permits. This way the new firewall is working at the corporate office with the remote site's configuration file and should work fine when it reaches at the remote site. Then have them send the old one back to redo for another site.
I know it's a PITA. Might be good for critical sites that can't go down for any period of time. Hopefully soon we can get these upgrade issues sorted out.
-
I have a faulty image in my hands now, hopefully I can track down a solution soon.
Current theory is that it was actually corrupt before the latest update and it just started to show it now, but once I have more time to experiment with the broken CF image I'll know for sure.
I'm certain we can come up with a fix, but it might be something scary like doing a DD of a good partition table to the start of the disk. Not something I'd generally recommend however in theory all NanoBSD images of the same size should have the same partition layout so it may be safe.
In the meantime I'd like to find out if everyone involved here had 4GB NanoBSD images, or both 2GB and 4GB, or even more.
-
Both 4GB CF for me.
-
2 and 4GB for me.
-
Jim,
I have both 2G and 4G nanobsd images displaying this problem.
Michael
