Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    DHCP on VLAN

    Scheduled Pinned Locked Moved DHCP and DNS
    13 Posts 2 Posters 2.6k Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • H
      hkstsony
      last edited by

      I have a fairly complicated setup:

      Multi-WAN doing a load balancing in pfSense
      5 Vlans setup on one interface and 1 DMZ setup on another interface
      Vlan 1 being used for Management w/o DHCP Server
      Vlan 24 for intranet Wifi w DHCP Server
      Vlan 30 for intranet w/o DHCP Server
      Vlan 50 for Public Wifi w DHCP Server
      Vlan 100 for Ubiquiti ToughSwitch and APs, w DHCP Server
      Now, the Vlan goes to a Cisco SG500X switch in port 1, trunk mode, Vlan 1UP, 24T, 30T, 50T, 100T
      port 35, trunk mode, Vlan 1T, 24T, 30T, 50T, 100UP, goes to Ubiquti ToughSwitch
      In Ubiquiti ToughSwitch, Vlan 1, 24, 30, 50 all tagged and 100 untagged
      ToughSwitch goes to UAPs with Vlan 24, 30, 50

      Now, my problem is, I'm not able to ping any of the APs
      I'm not able to SSH to any of the APs
      It's like being isolated

      In my firewall settings, I allowed all traffics but still no luck
      Can anyone give me some lights here please?

      1 Reply Last reply Reply Quote 0
      • H
        hkstsony
        last edited by

        I'm not able to get an IP from DHCP server if I set a port in 100UP access

        1 Reply Last reply Reply Quote 0
        • DerelictD
          Derelict LAYER 8 Netgate
          last edited by

          port 35, trunk mode, Vlan 1T, 24T, 30T, 50T, 100UP, goes to Ubiquti ToughSwitch
          In Ubiquiti ToughSwitch, Vlan 1, 24, 30, 50 all tagged and 100 untagged

          Pretty sure you can't tag VLAN ID 1.  (My Brocade ICXs won't even take tagged/untagged port commands on VLAN 1).

          Do yourself a favor and just create another VLAN ID and use it in place of VLAN 1 and tag all your traffic.  Forget VLAN ID 1 exists.  Don't use it.  If you have specific devices that require management on untagged and tag SSIDs, use the switchport to do that, but not on VLAN ID 1.

          Chattanooga, Tennessee, USA
          A comprehensive network diagram is worth 10,000 words and 15 conference calls.
          DO NOT set a source address/port in a port forward or firewall rule unless you KNOW you need it!
          Do Not Chat For Help! NO_WAN_EGRESS(TM)

          1 Reply Last reply Reply Quote 0
          • H
            hkstsony
            last edited by

            But even if I set a port in cisco as access and just V100, it is not able to get IP from pf

            1 Reply Last reply Reply Quote 0
            • DerelictD
              Derelict LAYER 8 Netgate
              last edited by

              Then things are not how you think they are.

              If you have a pfSense interface assigned to eth0_vlan100 with DHCP enabled going to a switchport configured for tagged trafic on VLAN 100, devices connected to switchports configured for untagged vlan 100 will get DHCP.

              Chattanooga, Tennessee, USA
              A comprehensive network diagram is worth 10,000 words and 15 conference calls.
              DO NOT set a source address/port in a port forward or firewall rule unless you KNOW you need it!
              Do Not Chat For Help! NO_WAN_EGRESS(TM)

              1 Reply Last reply Reply Quote 0
              • H
                hkstsony
                last edited by

                Do I need to setup DHCP relay or DHCP server in cisco switch?
                Thanks

                1 Reply Last reply Reply Quote 0
                • DerelictD
                  Derelict LAYER 8 Netgate
                  last edited by

                  Not if it's on the same layer 2 segment as the interface running the DHCP server, no.  And if it was, DHCP would work.

                  Again, with you tagging VLAN1 to the toughswitch, I have no idea what your network is going to do.  Apparently it's going to behave in unpredictable ways as you're finding out.

                  I don't understand why you are choosing to try to tag VLAN 1 and untag VLAN 100 across that trunk port. That makes no sense to me.

                  You are also dismissing my advice to get off VLAN 1 and tag EVERYTHING between pfSense and the Cisco and the Cisco and the toughswitch…  There is absolutely no reason to have untagged traffic between switches.  Every vendor seems to handle mixing tagged and untagged traffic on a port differently.  You are setting yourself up for major headaches that can be easily avoided by getting off VLAN 1 and tagging everything across your trunk ports.

                  Chattanooga, Tennessee, USA
                  A comprehensive network diagram is worth 10,000 words and 15 conference calls.
                  DO NOT set a source address/port in a port forward or firewall rule unless you KNOW you need it!
                  Do Not Chat For Help! NO_WAN_EGRESS(TM)

                  1 Reply Last reply Reply Quote 0
                  • H
                    hkstsony
                    last edited by

                    It's a layer 3 switch
                    I've removed all the Vlan 1 tagging
                    I'm able to discover the Ubiquiti TouchSwitch now
                    But still no luck with the APs

                    1 Reply Last reply Reply Quote 0
                    • DerelictD
                      Derelict LAYER 8 Netgate
                      last edited by

                      Is it a layer 3 switch as layer 3 or a layer 3 switch but only being used as layer 2?

                      You'll have to tell us how your network exists now.  Diagram?

                      How are the switchports going to the APs configured?

                      ToughSwitch goes to UAPs with Vlan 24, 30, 50

                      How do you expect them to get DHCP on VLAN 100 if they are only on VLANs 24, 30, and 50?

                      What does ubiquiti require for the APs to be initially configured?  I usually have to put my new APs (not ubiquiti) on an untagged port on my management VLAN until they get the config from the controller.  They get firmware, restart a couple times, then I move them to an tagged port in their final install location and everyone's happy.

                      Chattanooga, Tennessee, USA
                      A comprehensive network diagram is worth 10,000 words and 15 conference calls.
                      DO NOT set a source address/port in a port forward or firewall rule unless you KNOW you need it!
                      Do Not Chat For Help! NO_WAN_EGRESS(TM)

                      1 Reply Last reply Reply Quote 0
                      • H
                        hkstsony
                        last edited by

                        It's a layer 3 switch as layer 3
                        Current setup like this

                        Thank you very much
                        I'm new to VLAN and Layer 3 Switches
                        Previously we only have Layer 2 Switches and it runs without any issues
                        After we change out 2 Layer 2 Switches and replaced with 2 Layer 3 Switches stacked together, I'm no longer able to see those APs from pfSense

                        1 Reply Last reply Reply Quote 0
                        • DerelictD
                          Derelict LAYER 8 Netgate
                          last edited by

                          That still doesn't tell us how the ports to the UAPs are configured.  Is it 24T, 30T, 50T, 100T or 24T, 30T, 50T, 100U.  The initial configuration might require some untagged interfaces on 100, but, IMHO, your goal should be to get the access points' management VLAN set to 100 and have the switchports from the toughswitch to the UAPs as 24T, 30T, 50T, 100T.  Not sure what Ubiquiti recommends.

                          Chattanooga, Tennessee, USA
                          A comprehensive network diagram is worth 10,000 words and 15 conference calls.
                          DO NOT set a source address/port in a port forward or firewall rule unless you KNOW you need it!
                          Do Not Chat For Help! NO_WAN_EGRESS(TM)

                          1 Reply Last reply Reply Quote 0
                          • H
                            hkstsony
                            last edited by

                            UAPs are 24T, 30T, 50T, 100UP
                            The initial configurations are already done without Layer 3 switch
                            What makes the APs unseen is replacing Layer 2 switches with Layer 3 switch
                            Not sure if I need to setup more on pfSense and then DHCP relay on Layer 3 switch?

                            1 Reply Last reply Reply Quote 0
                            • DerelictD
                              Derelict LAYER 8 Netgate
                              last edited by

                              If you're not using layer 3 functions of your switch, it's not a layer 3 switch.  If you are, then you need to do all sorts of things differently.  If you are not configuring virtual interfaces and assigning interface IP addresses in the switch, it's just layer 2.

                              Chattanooga, Tennessee, USA
                              A comprehensive network diagram is worth 10,000 words and 15 conference calls.
                              DO NOT set a source address/port in a port forward or firewall rule unless you KNOW you need it!
                              Do Not Chat For Help! NO_WAN_EGRESS(TM)

                              1 Reply Last reply Reply Quote 0
                              • First post
                                Last post
                              Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.