Apcupsd Failing (USB Device)

bmeeks

Hi,

This is very likely me, but I just can't get it working … :(. Has anyone been able to get apcupsd working with a USB device (in pfSense v2.2)?

I have tried all the options I can think of for the Type / Device (blank, /dev/ugen2.3, etc.) ... but no luck. I have the cable set to usb, but it doesn't seem to find the device. (though I can see it it dmesg).

Suggestions?

Thanks!

This is not an answer to your precise question about apcupsd, but I do have an APC USB UPS connecting just fine using the NUT package. Have you tried NUT, or do you especially need the apcupsd package?

Bill

arrmo

It's a good answer actually … :). Thanks!

Nope, nut would be fine as well. Just tried it, but when I try to start it I get the following - have you seen this?
starting usbhid-ups
/usr/local/etc/rc.d/nut.sh: /usr/local/libexec/nut/upsdrvctl: not found
usbhid-ups failed to start

Thanks again.

bmeeks

@arrmo:

It's a good answer actually … :). Thanks!

Nope, nut would be fine as well. Just tried it, but when I try to start it I get the following - have you seen this?
starting usbhid-ups
/usr/local/etc/rc.d/nut.sh: /usr/local/libexec/nut/upsdrvctl: not found
usbhid-ups failed to start

Thanks again.

No, I had no issues at all with NUT. That error indicates to me that something did not install correctly. The same underlying issue might also be impacting apcupsd. What version of pfSense are you running?

Bill

arrmo

Hi,

Yep, thinking the same thing. I'm running v2.2 of pfSense … perhaps an issue with v2.2?

Thanks!

bmeeks

@arrmo:

Hi,

Yep, thinking the same thing. I'm running v2.2 of pfSense … perhaps an issue with v2.2?

Thanks!

Yep. The installation path (or at least the path that the error message indicated) does not appear correct for 2.2 unless proper symlinks are in place. It should be /usr/pbi/{package_name-arch}/…

Do you see a symlink for /usr/local/libexec that points to a folder similar to what I indicated above? You will need to run this command from the console or a SSH session –

ls -l /usr/local

Bill

arrmo

Hi,

/usr/local/libexec exists (doesn't look to be a symlink though). The only thing inside the directory is ipsec.

Thoughts?

Thanks!

bmeeks

@arrmo:

Hi,

/usr/local/libexec exists (doesn't look to be a symlink though). The only thing inside the directory is ipsec.

Thoughts?

Thanks!

My guess is the packages are not installing correctly on 2.2. In the past there were some issues with the PBI infrastructure in the 2.2-ALPHA snapshots, but I thought those had been fixed. You could try posting this in the 2.2-ALPHA snapshot feedback forum to see if one of the developers notices, or enter a bug in the bug tracker at https://redmine.pfsense.org

Bill

arrmo

Will post the info - thanks!

chpalmer

Hi

Any luck with this issue? I dont see any tickets on Redmine.

arrmo

Hi,

No luck, but no posting either - I was waiting for things to stabilize a bit, then retest (and post then if needed). Are things stable enough for that?

Thanks!

arrmo

Hi,

Neither NUT nor APCUPSD seem to be working … any thoughts of what to check (and what to post to the bug tracker)?

Thanks!

bmeeks

@arrmo:

Hi,

Neither NUT nor APCUPSD seem to be working … any thoughts of what to check (and what to post to the bug tracker)?

Thanks!

This may be a factor – I notice on my 2.2-BETA virtual machine I use for package testing that a USB driver error is logged to the console during boot-up. I have not investigated the error, and I don't currently have a copy of the text, but I have seen it for a long time when booting the VM and watching the console messages scroll by. It has persisted through many snapshot updates. The problem occurs early in the boot process.

Bill

ndyserinck

Hi Arrmo,

I was also stuck on it ^^
Regardless, I tried several way (trying make some rules, etc..) and when I checked the apcaccess arguments on internet, I noticed that a NIS serveur is mandatory.

In the apcupsd options in pfsense, I didn't activate it. After Y choose "On", listening on 0.0.0.0 and port 3551 it worked for me..

Hope this can help you.

Best regards

arrmo

Hi,

Are you on v2.2? Only asking because I'm not sure what you mean by "After Y" … :(. I do have the server on 0.0.0.0 / port 3551, this is the default. But I still get the error,

: Bogus configuration value (invalid-ups-type)
Terminating due to configuration file errors.

If I manually edit /usr/pbi/apcupsd-amd64/etc/apcupsd/apcupsd.conf, changing
UPSTYPE BLANK -> UPSTYPE (and nothing after this).

Then tried to restart, by
/usr/pbi/apcupsd-amd64/etc/rc.d/apcupsd onestart

But I get the error message,
/usr/pbi/apcupsd-amd64/etc/rc.d/apcupsd: WARNING: /usr/local/etc/apcupsd/apcupsd.conf is not readable.
/usr/pbi/apcupsd-amd64/etc/rc.d/apcupsd: WARNING: failed precmd routine for apcupsd

So some links are not working?

Thanks!

ndyserinck

Hi,

Here is my conf (values are without quotes):

General configuration parameters

Enable : "Yes"
UPS Cable : "usb"
UPS Type / Device : "usb"
Device : ""
Poll Time : "5"
Kill on Power Fail : "No"
Lock File : ""

Configuration statements for Network Information Server

Net Server : "On"
NIS Ip : "0.0.0.0"
NIS Port : "3551"

Before I set "on" for the NIS, in the /var/log/apcupsd.events, I was able to see "apcupsd 3.14.10 (13 September 2011) freebsd startup succeeded" and if I remove the power cord from the UPS, the log showed "Power failure." with a console alert.

About pfSense, it's installed in 2.1.5-RELEASE (amd64)
And for the "After Y", i mistype ^^. It's "After I choose…"

I attached my /usr/pbi/apcupsd-amd64/etc/apcupsd/apcupsd.conf file on this post. Hope this can help you.

Best Regards

apcupsd.conf.txt

arrmo

Thanks very much for the help - much appreciated!

Your config makes sense - I agree, a bit odd about the server, but glad it works for you. I think my issue is related to links missing in v2.2 … :(.

Thanks again.