Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    Silicom PXG6BPi or PXG4BPi FreeBSD driver source code Needed…

    2.2 Snapshot Feedback and Problems - RETIRED
    2
    20
    5.5k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • J
      joe_cowboy
      last edited by

      Well, I could unplug them but they are inside my pfsense box and I would have to tear it apart.  I modded a Neoware thin client case so I could put external antenna on it.  I tried adding to loader.conf.local the line if_run_load="YES" but when it boots it says run already loaded.

      1 Reply Last reply Reply Quote 0
      • stephenw10S
        stephenw10 Netgate Administrator
        last edited by

        Maybe not for USB drivers then.  :(

        Steve

        1 Reply Last reply Reply Quote 0
        • J
          joe_cowboy
          last edited by

          I am surprised I am the only one with this issue with this run0 USB interface.  I remember when Pfsense 2.0 was in dev hostap setting was an issue with the php setting it in the web interface.  But this is now a driver issue and hostap with in the driver according to that bug report.  But will not be sure unless the dev team was nice enough to try that fix with their code.  Or I get the nerve up and compile the Pfsense kernel myself and like you said go through the hoops to set up an account.

          If I could just disable the interfaces from coming up for now so I can finish the upgrade…  :o

          1 Reply Last reply Reply Quote 0
          • stephenw10S
            stephenw10 Netgate Administrator
            last edited by

            Can you not just remove those sections from the config.xml file?

            I have a run USB device and it works fine. It won't run as client but in hostap mode no issues. Might not be the same chipset as yours.
            https://wikidevi.com/wiki/TP-LINK_TL-WN7200ND

            Steve

            1 Reply Last reply Reply Quote 0
            • J
              joe_cowboy
              last edited by

              I tried removing those from the config.xml, cause interface mismatch, kernel panic and reboot.  :-\

              1 Reply Last reply Reply Quote 0
              • J
                joe_cowboy
                last edited by

                Is there a way to upgrade from the Pfsense command prompt using the latest.tgz.  Since the console menu is not loaded.

                1 Reply Last reply Reply Quote 0
                • stephenw10S
                  stephenw10 Netgate Administrator
                  last edited by

                  The command called by the console menu is:

                  php -f /etc/rc.initial.firmware_update

                  You could try that.

                  Steve

                  1 Reply Last reply Reply Quote 0
                  • J
                    joe_cowboy
                    last edited by

                    Thanks for the command!!!  I looked high and low for that.  Well, I was able to roll back to Pfsense 2.1.5.

                    I am wondering why when it gives you interface mismatch, it crashes and it doesn't prompt you for setting up your interfaces?

                    I will be cracking the box open here in a few days when I get my 6 port version of the card in.  Right now I have the 4 port of the bypass card installed.  It's been a rock solid card.  What I am going to do is get away from the USB Nics I have installed on the box so my interfaces will stop going up and down on them.  The axe drivers for it never could keep the interface up for a very long time before I had to reset it.  I looked into that issue too and with the newer 9.x and newer of the kernel should fix that issue according to forum threads on FreeBSD.

                    My thing is getting the two run USB WiFi interfaces to come up with out a kernel panic and crash.  I will get you the actual USB WiFi interface when I take the unit apart.  When I bought the USB WiFi stick it was one that was recommended; I remember that.

                    They are rock solid under Pfsense 2.1.5 and I know it's kernel 8.3 but the issue does seem like the issue I posted the link to….

                    1 Reply Last reply Reply Quote 0
                    • stephenw10S
                      stephenw10 Netgate Administrator
                      last edited by

                      Dropping to the interface assign menu is the expected behaviour, hard to say why your system isn't doing that. You say it only started after you enabled the interfaces? Are they identical? It might be worth trying only one.

                      Steve

                      1 Reply Last reply Reply Quote 0
                      • J
                        joe_cowboy
                        last edited by

                        It only started it after I upgraded the system to Pfsense 2.2 because Pfsense 2.1.5 both of the Wifi interfaces work perfectly.

                        1 Reply Last reply Reply Quote 0
                        • First post
                          Last post