Update 2.1.5 to 2.2 fails on APU
-
I also tried to rename the bsnmpd.conf - without luck.
I tried different things and in the end, it's working now …
1. I installed 2.2 (memstick-serial-release) using an usb stick - using default values during installation process.
2. I booted up the pfsense and configured the necessary VLAN, the WAN and the LAN interface via serial console.
3. I imported the config.xml (copied away from the "old" failed installation via usb drive) over the webinterface - NOPE, after a reboot, I had the same problems again
4. I started over (steps 1 & 2) and imported only parts (areas) from the old config.xml via the webinterface - SUCCESS. Just without OpenVPN certificates yet ...
5. I exported the current configuration via the webinterface, inserted ONLY the <ca>- and <cert>-section of the old config.xml into the new config.xml. Then I restored the modified configuration via the webinterface (areas: "all") and rebooted - NOPE, same problems ...
6. I started over (steps 1, 2, 4). First I thought there might be something wrong with the certificates, but: I exported the configuration via the webinterface, and restored EXACTLY THE SAME configuration via the webinterface (areas: "all") - NOPE, same problems ...
7. In the end, I started over (steps 1, 2, 4), downloaded the current configuration via webinterface, inserted the <ca>- and <cert>-sections, copied this config to an usb-drive, and replaced the file /cf/conf/config.xml with this file. After a reboot, everything is working, even OpenVPN.I'm wondering if the WebGUI-Restore-Functionality is broken in 2.2 ... ?
Export seems to work without problems, as I used it for my current configuration (step 7)Greetz
lousek</cert></ca></cert></ca> -
If the problem is only related to bsnmpd and for those who can live without snmp, isn't it enough to simply disable snmp before upgrading and then upgrade to 2.2 ?
-
Someone that can replicate this, could you get me a config that exhibits the issue? I've tried a wide range of things and haven't found a way to replicate. Could PM it to me.
@GLR:
If the problem is only related to bsnmpd and for those who can live without snmp, isn't it enough to simply disable snmp before upgrading and then upgrade to 2.2 ?
Yes, that would be adequate.
-
Isn't it enough to (try to) run 2.2 on an APU unit with bsnmpd enabled ?
-
Eh???
-
We've tracked down the source of this one. It appears to be only when you're running from mSATA and have no SD card installed.
https://redmine.pfsense.org/issues/4403Not down to a specific root cause yet, just know it appears to be specific to that circumstance where you don't have a SD card in the system, and you enable SNMP.
Anyone here seeing this happen who has a SD card installed in their APU?
-
Yes, I don't have any mSATA module but only a SD card.
-
Hi all
I've a similar same problem. As yu can see below the system is on SD.
I tried to upgrade with the webGui. Neither Manual Update nor Auto Update were working. It just rebooted with the old version.
CPU:AMD G-T40E Processor, 2 CPUs: 1 package(s) x 2 core(s)
Version: 2.1.5-RELEASE (amd64) built on Mon Aug 25 07:44:45 EDT 2014
Plattform: nanobsd (4g)Did anyone manage to update on such configuration from 2.15 to 2.2? Any advice is most welcome!
Many thanks!
Patrick -
If it rebooted to the previous version it's failed to update for some reason, not the same issue as described by this thread. Check the upgrade log in Diagnostics > Nanobsd for errors. Start a new thread if there's nothing in there about bsnmpd.
Steve
-
This looks a whole lot like the upgrade failure that I got on my soekris 6501. I'm running mSATA only, but I don't use snmp, and that's an Atom e6xx chip. i386 full install.
-
Hi
In the meanwhile I found out that can't do changes anymore. It seemed that the hd is only readonly mountable.
I therefore decided to reinstall the whole system on v2.2. With the backup I got it finally working after a fair amount of efforts with the new version of pfsense.
Shit happens. :)
Patrick
-
Indeed it does! ::)
In NanoBSD the filesystem is supposed to be mounted read-only. It gets re-mounted as read write only when a config change is saved. It is designed that way to prevent excess writes to flash media.
https://www.freebsd.org/doc/en_US.ISO8859-1/articles/nanobsd/Steve
