Is this a good appliance for my setup?
-
and its going up 80% CPU Usage.
Did you enable PowerD (max.)?
@Evancool
Snort & HAVP perhaps on top Squid & SquidGuard would be causing more then the Atom 1,6 GHz is able to serve.
So at this days it would be the best and also future proofed to go with an Intel Atom C2xxx board in my eyes.
Supermicro is producing C23xx, 25xx and 27xx boards with 2, 4 and 8 core cpu´s and they are sufficient to
manage all this options and features given by pfSense. Mini ITX cases that will fitting perfect are also in the
run from Supermicro, if this would be to high pricing you should go by a Jetaway board with 2 core and 3,0
GHz or narrow down the entire features you will be using. -
Thanks. Yes I did study the C2xxx Atoms from Supermicro. I really wanted a C2758 but was just too expensive. The lesser supermicros were still in the $300+ range. My max would be $200 for now. I do realize the 1.6 atom on the ebay item is only single core but I am hoping the hyperthreading and leaving PowerD off can make up for it a little.
-
@Evancool:
The lesser supermicros were still in the $300+ range. My max would be $200 for now. I do realize the 1.6 atom on the ebay item is only single core but I am hoping the hyperthreading and leaving PowerD off can make up for it a little.
Don't forget those 'older' atoms are 32-bit only. I think it would be wise to get a platform that runs 64-bit. Maybe you can find a different board based on a C2358 within your budget? I would rather have had a C2758 myself, but when I look at the CPU load with my C2558, it's just not needed for semi-professional use.
Of course I would really like this board: http://www.supermicro.nl/products/motherboard/Xeon/D/X10SDV-8C-TLN4F.cfm
As long as I'm not paying for it myself! :o -
PowerD off can make up for it a little.
Please don´t do so, this can be also running in the total other direction as you imagine or expect it!
Alix APU:- ~400 - 450 MBit/s throughout with PowerD off
- ~680 - 750 MBit/s throughput with PowerD on
-
And which option do you recommend with PowerD?
- Hidaptive
- Adaptive
- Minimum
- Maximum
Which option gives the best performance, and which the poorest?
-
as I am right informed you will be able to set it up as you or your hardware will be
need it or you want to save electric power.And which option do you recommend with PowerD?
Even that one that matched your personal needs (this can be differ from user to user)
or what matches right your hardware, making pfSense runs smooth and liquid!pfsense > System > Advanced > Miscellaneous
- Hidaptive
PowerD is only using the maximum of the CPU clock frequency
- Adaptive
PowerD is using from the minimum to the maximum of the CPU clock frequency
- Minimum
PowerD is only using the minimum of the CPU clock frequency
- Maximum
PowerD is only using form the minimum to the maximum of the CPU clock frequency (recommended)
From the pfSense Doc`s:
To force it to use EST rather than throttling or p4tcc add the following lines to loader.conf.localhint.p4tcc.0.disabled=1 hint.acpi_throttle.0.disabled=1ACPI throttling and p4tcc do not provide any measurable power saving.
If I am wrong, please correct me.
-
Read this:
https://www.ateamsystems.com/tech-blog/increase-freebsd-performance-with-powerd/So if these guys are correct you need to enable PowerD if you want to use speedstep and/or turbo boost.
-
I've played around with PowerD on Supermicro A1SRi-2758f. When enabled and set to Hidaptive, preformance decreases dramatically at start. After about 5 to 10 seconds, it wakes up fine.
So I have about 80-85Mbit/sec for the first 5 to 10 seconds, which afterwards jumps to the expected gigabit-close value.
Not good.
Without PowerD enabled, it runs properly at max throughput.That motherboard has so little power usage even when maxed out, that it's simply not worth the trouble of fooling around with jumping CPU speeds.
-
Atom N270 - ancient. Don't buy it.
-
Supermicro A1SRi-2758f is not based on Atom N270.
-
I just answered the first original question only…
