Pfsense Install on Nokia IP390
-
Did you reconnect your client to one of the interfaces in the bridge? When you re-assign LAN the old interface will become inactive.
Did you set the sysctls before you created the bridge? If not then just reboot and the new bridge will be brought up with the new settings.
If you have somehow not configured the firewall correctly you can temporarily disable the firewall completely from the console while you add appropriate rules:
https://doc.pfsense.org/index.php/I_locked_myself_out_of_the_WebGUI,_help!#Remotely_Circumvent_Firewall_Lockout_by_Temporarily_Changing_the_Firewall_RulesSteve
-
Hmm. Yes, I did reconnect it to a bridge interface.
If you mean sysctls as in system tuneables, then yes.. If it's something else, then.. Nope.
I'll look into that if I have set the sysctls correctly
-
Help.. cant get ip390 to boot , ive tried 32 bit version and 64 bit version , putty com1 gets to boot 1 then just loads of crap fills the screen any ideas ?
-
What image are you booting?
It could be the baud rate changes at that point, after the boot loader.
It's 115200 if you're using 2.2.XSteve
-
Just a heads up..
You can write the image to a CF card, and use that card to install to the hard drive. You can then remove the card and have it boot to the hard drive.
I'm looking into upgrading the 1.5GHz Celeron-M (Banias) processor with a 2.0GHz Pentium-M (Dothan) for better performance.
-
cant get the ip390 to boot from hard drive
-
So, My recent adventure included….guess... pfsense and an IP390. I think this may help you guys with the LED's. The IP390 I got on eBay had a factory reset cf with ipso 4.2, and turned off the led's, where pfsense did not, I decided to dig.
From file "ipso_startup_complete" from a seperate ipso 6.2 install at "~\ipso-6.2\ipso-6.2\etc\rc.d"
ipsctl -w -n hw:sys_stat:state:startup 0 hw:sys_stat:state:ok
Let me know if this is a projected that was given up on, or if someone needs ref. files.
Adam,
Bombshell Networks -
If you have the files we can look at them but I thought they existed only as compiled binaries.
Steve
-
http://www.mediafire.com/download/811gge17b8ofl6m/pfsenseforum-nokia.zip
-
Sorry I don't actually have an IP390 to test that.
Someone else might be able to use the binary on the real hardware ans look for the settings it's making.Steve
-
Just coming back to give an update on my pfSense project on my IP390:
It's been amazing for the time i've been running it now. Hasn't crashed once. Admittedly I didn't get all the lights working properly so it still displays the system error light but if otherwise it works fine. Only problem I had was when an engineer decided to disconnect the internal fans and it blew a power supply! I had a spare so that was fine, but recommendation: replace all those fans, and make sure they're plugged in. Seriously not cool if you don't have a spare supply around.
-
So, My recent adventure included….guess... pfsense and an IP390. I think this may help you guys with the LED's. The IP390 I got on eBay had a factory reset cf with ipso 4.2, and turned off the led's, where pfsense did not, I decided to dig.
From file "ipso_startup_complete" from a seperate ipso 6.2 install at "~\ipso-6.2\ipso-6.2\etc\rc.d"
ipsctl -w -n hw:sys_stat:state:startup 0 hw:sys_stat:state:ok
Let me know if this is a projected that was given up on, or if someone needs ref. files.
Adam,
Bombshell NetworksNot so much given up on, but I haven't really had the time to continue messing as late. But i'm guessing that you're talking about an IPSO command right there? I think I found that when I was digging around in the IPSO firmware that came on one of my units. I think I tried to look into this but we need the hardware reference of "sys_stat" in order to set this on or off.
-
Just wondered if you know the error codes on startup - I have an ip390 here and was working fine - restarted it and I get 41 on the on board LED and no serial output.
-
A few quick searches show "41 - OEM post memory initialization codes", maybe swap out ram, or maybe bad ram slot?
-
there are 3 LED related functions in the Check Point kernel ...
- janus_pld_red_led_set (Bit 0x01)
- janus_pld_yellow_led_set (Bit 0x02)
- janus_pld_green_led_set (Bit 0x08)
they write to port 0x348 ... this seems to be the Altera MAX II chip (PLD) next to the diag display
btw: the PLD also monitors powersupply status
... and there are 4 LED related functions for 'Phalanx PLD' ... - phalanx_pld_red_led_set
- phalanx_pld_yellow_led_set
- phalanx_pld_green_led_set
- phalanx_pld_disk_led_set *****
this might be the explanation for the 'missing' led on the frontpanel PCB (Bit 0x04 is assume)
hope this helps - sorry for the late reply ;)
/paketix
