Network issues after 2.2.4 installation to disk
-
I installed from the live CD ISO image to a Dell PE850 with dual on board NICs.
During the boot off the CD there were some nasty looking SCSI error messages and the boot was …s....l....o....w....
The boot image is a straight image off a USB or HD isn't it? It tries to write to the image it's booting from and eventually times out doesn't it?
(Other OS's boot fine off this CD drive, so yea, it's not hardware...)After finally getting the install onto the hard drive, I have the LAN interface connected to a switch, using the default 192.168.1.1 address, and a laptop manually configured at 192.168.1.2 on another port on the same switch.
Neither machine can access the other --- no ping. pfSense command line actually returns a "no buffer" message after a bit.
I logged into a shell from the console on the Dell and ifconfig shows both interfaces on the box with "no carrier", which I assume means no network/device link.
I have confirmed that the NIC on the Dell and the switch port both indicate a 1GB connection/link is present. (I have briefly connected the other interface on the Dell to the same network to ensure that I have not made a mistake and selected the wrong port. Same results.)I was at least able to get 2.2.(2 ? I think it was past this point).
Any clues?
Where am I failing in what appears to be a very obvious installation path? -
I can confirm the trouble installing 2.2.4 release directly on 2G CF-card on an ALIX.2d31. It was my first try with pfSense. After changing the baud-rate to 115200 I could
read the boot messages:
Welcome to pfSense 2.2.4-RELEASE …
Creating symlinks......ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib
a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout
done.Under 512 megabytes of ram detected. Not enabling APC.
External config loader 1.0 is now starting...
Launching the init system... done.
Initializing...................... done.
Starting device manager (devd)...done.
Loading configuration......done.Default interfaces not found -- Running interface assignment option.
vr0: link state changed to DOWN
vr1: link state changed to DOWN
vr2: link state changed to DOWNValid interfaces are:
vr0 00:0d:b9:20:d4:38 (up) VIA VT6105M Rhine III 10/100BaseTX
vr1 00:0d:b9:20:d4:39 (up) VIA VT6105M Rhine III 10/100BaseTX
vr2 00:0d:b9:20:d4:3a (up) VIA VT6105M Rhine III 10/100BaseTXDo you want to set up VLANs first?
If you are not going to use VLANs, or only for optional interfaces, you should
say no here and use the webConfigurator to configure VLANs later, if required.Do you want to set up VLANs now [y|n]? vr0: link state changed to UP
this was the end and the network 192.168.1.1 is not coming up. My NIC connected to LAN got
following addresses:
Ethernet-Adapter LAN-Verbindung:
Verbindungsspezifisches DNS-Suffix:
Verbindungslokale IPv6-Adresse . : fe80::7cb3:965d:c1eb:67f8%11
IPv4-Adresse (Auto. Konfiguration): 169.254.103.248
Subnetzmaske . . . . . . . . . . : 255.255.0.0
Standardgateway . . . . . . . . . :
after some slef-doubts I looked for an older image and found
pfSense-2.1.3-RELEASE-2g-i386-nanobsd-20140501-1552.img
which I could install succesfully and read with 9600 baudrate. Newer images I did not find out there.Bootup complete
FreeBSD/i386 (pfSense.localdomain) (console)
*** Welcome to pfSense 2.1.3-RELEASE-nanobsd (i386) on pfSense ***
WAN (wan) -> vr1 ->
LAN (lan) -> vr0 -> v4: 192.168.1.1/24- Logout (SSH only) 8) Shell
- Assign Interfaces 9) pfTop
- Set interface(s) IP address 10) Filter Logs
- Reset webConfigurator password 11) Restart webConfigurator
- Reset to factory defaults 12) pfSense Developer Shell
- Reboot system 13) Upgrade from console
- Halt system 14) Enable Secure Shell (sshd)
- Ping host 15) Restore recent configuration
Enter an option:
My NIC connected to LAN
Ethernet-Adapter LAN-Verbindung:
Verbindungsspezifisches DNS-Suffix: localdomain
Verbindungslokale IPv6-Adresse . : fe80::7cb3:965d:c1eb:67f8%11
IPv4-Adresse . . . . . . . . . . : 192.168.1.10
Subnetzmaske . . . . . . . . . . : 255.255.255.0
Standardgateway . . . . . . . . . : fe80::1:1%11
192.168.1.1Obviously the problem occured with 2GB NanoBSD (no VGA) flash issues (and upgrade issues) with 2.2.2
https://forum.pfsense.org/index.php?topic=92709.0Please check and fix this issue.
-
This was solved here https://forum.pfsense.org/index.php?topic=92709.0 from what I read over there.
I saw:
Under 512 megabytes of ram detected. Not enabling APC.
How much RAM do you have ?
-
This was solved here https://forum.pfsense.org/index.php?topic=92709.0 from what I read over there.
I saw:
Under 512 megabytes of ram detected. Not enabling APC.
How much RAM do you have ?
I have been able to stumble on through the install, and it's working at this point.
2GB of RAM in a Dell PowerEdge 850.After the installation of 2.2.4 I have gotten further with a functioning installation than any other attempt.
Maybe I'm just learning a bit more ???