Can't create new bridge
-
Ah, OK, so it never actually creates the bridge at all? No entry in the list on the bridges tab?
-
Nope. When I try to create the bridge it gives me the error from the first post and in the log I have the two lines from the first post.
-
Following through the code it looks like the only way that can happen is if the function to create a new bridge interface at the OS level fails. It's possible something is amiss with your setup or maybe even something didn't get upgraded properly (like the pfsense PHP module) but I'd expect far more trouble than this if that were the case.
Do any bridge interfaces show up in "ifconfig -a"?
I can't seem to reproduce any problem like this, you might want to back up the config, reinstall pfSense, and then restore the config to make sure you have a consistent FS/install.
-
This is what I get with the "ifconfig -a" command:
bge0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
options=8009b <rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum,linkstate>ether 00:11:43:0f:ec:06
inet6 fe80::211:43ff:fe0f:ec06%bge0 prefixlen 64 scopeid 0x1
inet x.x.x.x netmask 0xfffff800 broadcast x.x.x.x
nd6 options=21 <performnud,auto_linklocal>media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
re0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
options=8209b <rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum,wol_magic,linkstate>ether 00:1f:1f:fa:17:96
inet6 fe80::21f:1fff:fefa:1796%re0 prefixlen 64 scopeid 0x2
nd6 options=21 <performnud,auto_linklocal>media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
rl0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
options=2008 <vlan_mtu,wol_magic>ether 00:e0:4c:69:0f:20
inet6 fe80::2e0:4cff:fe69:f20%rl0 prefixlen 64 scopeid 0x3
inet 192.168.x.x netmask 0xffffff00 broadcast 192.168.x.x
nd6 options=21 <performnud,auto_linklocal>media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
ath0: flags=8802 <broadcast,simplex,multicast>metric 0 mtu 2290
ether f4:ec:38:b3:32:51
nd6 options=21 <performnud,auto_linklocal>media: IEEE 802.11 Wireless Ethernet autoselect (autoselect)
status: no carrier
pflog0: flags=100 <promisc>metric 0 mtu 33172
pfsync0: flags=0<> metric 0 mtu 1500
syncpeer: 224.0.0.240 maxupd: 128 defer: on
syncok: 1
lo0: flags=8049 <up,loopback,running,multicast>metric 0 mtu 16384
options=600003 <rxcsum,txcsum,rxcsum_ipv6,txcsum_ipv6>inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x7
nd6 options=21 <performnud,auto_linklocal>enc0: flags=0<> metric 0 mtu 1536
nd6 options=21 <performnud,auto_linklocal>ovpns1: flags=8943 <up,broadcast,running,promisc,simplex,multicast>metric 0 mtu 1500
options=80000 <linkstate>ether 00:bd:eb:70:00:01
inet6 fe80::2bd:ebff:fe70:1%ovpns1 prefixlen 64 scopeid 0x9
nd6 options=21 <performnud,auto_linklocal>media: Ethernet autoselect
status: active
Opened by PID 11050</performnud,auto_linklocal></linkstate></up,broadcast,running,promisc,simplex,multicast></performnud,auto_linklocal></performnud,auto_linklocal></rxcsum,txcsum,rxcsum_ipv6,txcsum_ipv6></up,loopback,running,multicast></promisc></performnud,auto_linklocal></broadcast,simplex,multicast></full-duplex></performnud,auto_linklocal></vlan_mtu,wol_magic></up,broadcast,running,simplex,multicast></full-duplex></performnud,auto_linklocal></rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum,wol_magic,linkstate></up,broadcast,running,simplex,multicast></full-duplex></performnud,auto_linklocal></rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum,linkstate></up,broadcast,running,simplex,multicast> -
Nothing unusual there… for giggles, try running this:
ifconfig bridge create(edit: just "bridge" not "bridge0" there)
-
Done.
[2.2.4-RELEASE][root@pfsense.x]/root: ifconfig bridge create
bridge0 -
Then I'd suspect something in the PHP install/libraries. At a minimum, try forcing an upgrade to the exact same version you're already on, though a reinstall would be a better bet.
-
Thanks, I think I'll try that out. Could be possible that a future upgrade to 2.2.5 (when it will come out) will solve my problem? :)
-
It's possible but difficult to say. I wouldn't wait for that to come along to fix it. 2.2.5 itself wouldn't likely be the fix, but whatever the upgrade might rewrite on the system itself would potentially help.
-
Thanks for your help. I'll reinstall pfSense, reconfigure it and I'll come back with the result.
-
It all works fine after the clean install. Thanks for the support :)
