Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    Question on WAN Failover

    Scheduled Pinned Locked Moved Routing and Multi WAN
    24 Posts 4 Posters 3.7k Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • DerelictD
      Derelict LAYER 8 Netgate
      last edited by

      You can do whatever you want.  Set your primary to Tier 1 and your secondary to tier 2 and you'll have failover.

      Chattanooga, Tennessee, USA
      A comprehensive network diagram is worth 10,000 words and 15 conference calls.
      DO NOT set a source address/port in a port forward or firewall rule unless you KNOW you need it!
      Do Not Chat For Help! NO_WAN_EGRESS(TM)

      1 Reply Last reply Reply Quote 0
      • S
        sstretchh
        last edited by

        Ok, thank you just wanted to make sure that would work.

        I wasn't sure if the load balancing had to be part of it for the fail over to work. I didn't think it needed to be, but thought I would ask since every tutorial I have seen shows the loadbalacning part in with the failover part

        1 Reply Last reply Reply Quote 0
        • DerelictD
          Derelict LAYER 8 Netgate
          last edited by

          And even without a failover event you are always free to policy route out the secondary link should you have the need.  You can still set the destination on a route or rule to the gateway itself instead of the failover group.  You can also set up a failover group with tier 1 and tier 2 reversed and policy route out that group too.  You would then simultaneously have both circuits in use, with both failing over to the other if one goes down.

          Chattanooga, Tennessee, USA
          A comprehensive network diagram is worth 10,000 words and 15 conference calls.
          DO NOT set a source address/port in a port forward or firewall rule unless you KNOW you need it!
          Do Not Chat For Help! NO_WAN_EGRESS(TM)

          1 Reply Last reply Reply Quote 0
          • S
            sstretchh
            last edited by

            ahhh that is good to know. I thought about routing all the kids devices out the microwave connection.

            so basically If I am understanding you correct, I could set up the Failover rule. But also set up all the kids devices to route out the slower connection.

            Is it easier to set up a 2nd DHCP scope to accomplish this.  I currently have DHCP static reservations on everything in the house

            1 Reply Last reply Reply Quote 0
            • DerelictD
              Derelict LAYER 8 Netgate
              last edited by

              If you have one subnet/LAN then static reservations is the way to go.  I'd pick a spot on a subnet boundary, say 192.168.1.192/26. Set your kids devices to DHCP assignments from 192.168.193 - .254

              Then, on LAN, down at the bottom pass any any rule that policy routes to the gateway group, right above it place a rule that routes with a source of 192.168.1.192/26 dest any to the microwave gateway (or the gateway group with the microwave as tier 1).

              If they're smart they can circumvent it with a static IP but…

              Chattanooga, Tennessee, USA
              A comprehensive network diagram is worth 10,000 words and 15 conference calls.
              DO NOT set a source address/port in a port forward or firewall rule unless you KNOW you need it!
              Do Not Chat For Help! NO_WAN_EGRESS(TM)

              1 Reply Last reply Reply Quote 0
              • S
                sstretchh
                last edited by

                How do I set which WAN I want to be the primary to start with and when the primary WAN comes back online how do I fail back over to the primary ?

                1 Reply Last reply Reply Quote 0
                • DerelictD
                  Derelict LAYER 8 Netgate
                  last edited by

                  In your gateway group Tier 1 is primary and Tier 2 is secondary.  Fail back is automatic.

                  gateway-groups.png
                  gateway-groups.png_thumb

                  Chattanooga, Tennessee, USA
                  A comprehensive network diagram is worth 10,000 words and 15 conference calls.
                  DO NOT set a source address/port in a port forward or firewall rule unless you KNOW you need it!
                  Do Not Chat For Help! NO_WAN_EGRESS(TM)

                  1 Reply Last reply Reply Quote 0
                  • S
                    sstretchh
                    last edited by

                    Yeah I have been trying to rack my head on how to read that. In my screen shot, did I make OPT1 (FTTC)primary ?

                    I want the OPT1 (FTTC) to be the primary WAN interface

                    GW2-groups.JPG
                    GW2-groups.JPG_thumb

                    1 Reply Last reply Reply Quote 0
                    • DerelictD
                      Derelict LAYER 8 Netgate
                      last edited by

                      @sstretchh:

                      Yeah I have been trying to rack my head on how to read that. In my screen shot, did I make OPT1 (FTTC)primary ?

                      I want the OPT1 (FTTC) to be the primary WAN interface

                      For that route to OPT1failoverWAN1

                      Chattanooga, Tennessee, USA
                      A comprehensive network diagram is worth 10,000 words and 15 conference calls.
                      DO NOT set a source address/port in a port forward or firewall rule unless you KNOW you need it!
                      Do Not Chat For Help! NO_WAN_EGRESS(TM)

                      1 Reply Last reply Reply Quote 0
                      • S
                        sstretchh
                        last edited by

                        You Lost me there, Where do i do that at ?

                        This is what i have so far. At this point I want to make sure I am set up to Failover from OPT1 (FTTC) to WAN1.

                        And if I understand what you said earlier it should auto fail back

                        Attached is what I have done so far.

                        GW2-groups.JPG_thumb
                        GW2-groups.JPG
                        FW-LAN-GW.JPG
                        FW-LAN-GW.JPG_thumb

                        1 Reply Last reply Reply Quote 0
                        • DerelictD
                          Derelict LAYER 8 Netgate
                          last edited by

                          Right there in the firewall rules.  Get rid of the second one. It will never be matched (it matches the same traffic as the rule above it so it will never be hit by matching traffic..)

                          Chattanooga, Tennessee, USA
                          A comprehensive network diagram is worth 10,000 words and 15 conference calls.
                          DO NOT set a source address/port in a port forward or firewall rule unless you KNOW you need it!
                          Do Not Chat For Help! NO_WAN_EGRESS(TM)

                          1 Reply Last reply Reply Quote 0
                          • S
                            sstretchh
                            last edited by

                            get ride of the WAN > OPT1 Rule ?

                            FW-LAN-GW_d.JPG
                            FW-LAN-GW_d.JPG_thumb

                            1 Reply Last reply Reply Quote 0
                            • DerelictD
                              Derelict LAYER 8 Netgate
                              last edited by

                              Yes.  it is unnecessary and will never match any traffic.

                              Chattanooga, Tennessee, USA
                              A comprehensive network diagram is worth 10,000 words and 15 conference calls.
                              DO NOT set a source address/port in a port forward or firewall rule unless you KNOW you need it!
                              Do Not Chat For Help! NO_WAN_EGRESS(TM)

                              1 Reply Last reply Reply Quote 0
                              • C
                                chidgear
                                last edited by

                                ninjaneer, This worked for you? I'm Kind of stuck here (trying to do my first failover on pfsense), so I am guiding myself with your post (I'm not so good with Firewall/NAT rules when it comes to forward traffic). Please, if something worked for you, let us know.

                                1 Reply Last reply Reply Quote 0
                                • DerelictD
                                  Derelict LAYER 8 Netgate
                                  last edited by

                                  I'm not so good with Firewall/NAT rules when it comes to forward traffic

                                  You should probably figure that out before tackling more advanced topics like multi-wan and the policy routing it entails.

                                  Chattanooga, Tennessee, USA
                                  A comprehensive network diagram is worth 10,000 words and 15 conference calls.
                                  DO NOT set a source address/port in a port forward or firewall rule unless you KNOW you need it!
                                  Do Not Chat For Help! NO_WAN_EGRESS(TM)

                                  1 Reply Last reply Reply Quote 0
                                  • C
                                    chidgear
                                    last edited by

                                    Can you suggest me some topic(s)? I think I expressed myself in the wrong way, I meant, "I'm not so good with Firewall/NAT rules when it comes to forward traffic on pfSense, because I got lost very easily with the interface" (Too many options at once) I'm still searching on the forum and the documentation, but it gets confusing because, or only a few people are having the problems that I have, or maybe I'm looking on the wrong direction (I'm thinking this is the main reason…)

                                    Thanks in advance!

                                    1 Reply Last reply Reply Quote 0
                                    • DerelictD
                                      Derelict LAYER 8 Netgate
                                      last edited by

                                      https://doc.pfsense.org/index.php/Firewall_Rule_Basics

                                      https://doc.pfsense.org/index.php/Firewall_Rule_Processing_Order

                                      https://doc.pfsense.org/index.php/Firewall_Rule_Troubleshooting

                                      https://doc.pfsense.org/index.php/How_can_I_forward_ports_with_pfSense

                                      https://doc.pfsense.org/index.php/Port_Forward_Troubleshooting

                                      Chattanooga, Tennessee, USA
                                      A comprehensive network diagram is worth 10,000 words and 15 conference calls.
                                      DO NOT set a source address/port in a port forward or firewall rule unless you KNOW you need it!
                                      Do Not Chat For Help! NO_WAN_EGRESS(TM)

                                      1 Reply Last reply Reply Quote 0
                                      • S
                                        sstretchh
                                        last edited by

                                        @chidgear:

                                        ninjaneer, This worked for you? I'm Kind of stuck here (trying to do my first failover on pfsense), so I am guiding myself with your post (I'm not so good with Firewall/NAT rules when it comes to forward traffic). Please, if something worked for you, let us know.

                                        I understand your frustration, having the links to the DOC's don't help everyone. I am a visual learner so the DOCs are nice if you want to understand a setting but doesn't help explain exactly what goes where.

                                        I used this link (below) in the beginning, but I didn't care about the load balancing part. Then I start this post and derelict posted and helped me out. In the end it worked for me. If OPT1 fails, it switchs to my WAN port. Once it detects the my OPT1 is up again it auto switches back.

                                        https://forum.pfsense.org/index.php?topic=28121.0

                                        1 Reply Last reply Reply Quote 0
                                        • S
                                          sstretchh
                                          last edited by

                                          childgear, if this helps you here are screenshots of my final configuration. I think with the groups I only needed the OPT1failoverWAN1 group, I don't think i needed to have the one that starts with WAN. Its still there because I was following instructions from another post and I believe its needed if you continue on to do the load balancing part

                                          this guys youtube video is pretty good also, if you comment with questions he replies pretty fast

                                          DUAL WAN ON PFSENSE 2
                                          Youtube Video

                                          Edited to add youtube link

                                          FW-LAN.JPG
                                          FW-LAN.JPG_thumb
                                          gateawys.JPG
                                          gateawys.JPG_thumb
                                          groups.JPG
                                          groups.JPG_thumb

                                          1 Reply Last reply Reply Quote 0
                                          • C
                                            chidgear
                                            last edited by

                                            Thank you everyone!, I'll try this when the workload gets down, so I can use both links. If it worked, I'll be back with some kudos XD

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.