Pulling my hair out !! Cannot access the web gui pfsense after install VICTORY

captain1980

Well i had a bright idea to get my GF old computer from her dads house.

I bought a cheap ass NIC card. I just wanted to make sure that i was not getting crazy.

Long story short. Got to the WEB GUI on the DELL PC doing the same install what i was doing all along.

Guess my nice new M350 case with PD11BI CC2 Mitac dual does not want to play with Pf sense.

I will try to replace it with the Intel NIC version.

For show see the pictures.

:o

image1.JPG_thumb
image2.JPG_thumb

image4.JPG_thumb

image3.JPG_thumb

captain1980

P.s.

http://mikepowells.net/2011/07/08/full-pfsense-on-embedded-hardware/

I read here if you have problems getting past the interface assignement in pfsense because you don,t have seperate interfaces for the LAN and WAN. The option is then to setup Vlans and create 2 Vlans interfaces.

Anybody thoughts on that ?

johnpoz

do you have a smart/managed switch that supports vlans? I thought your hardware had 2 nics?

captain1980

My initial setup is the M350 case with MITAC board and 2 NIC i have no success with that machine.

The big tower is a scratch computer i dig up and put a extra NIC in… this i got to working. So i can conclude the new M350 case build has some hard ware issue.

I think my initial setup (new build) is not doing well with Pf sense.

I tried the Vlan interfaces setup like described in the link but same result as before.

Its like the system does not see the interfaces as separate.

I made a last ipconfig and arp -a see picture. Set the laptop manual IP, gateway, subnet.

![ipconfig and arp.jpg](/public/imported_attachments/1/ipconfig and arp.jpg)
![ipconfig and arp.jpg_thumb](/public/imported_attachments/1/ipconfig and arp.jpg_thumb)

captain1980

Just another though:

I had problems with the initial setup of the BIOS. They advice me to put it in windows 7 default mode. Put settings in "legacy" mode. Original was set top UEFI boot but i could not load from the USB. Even not when i changed to boot order.

Could this be an issue ?

doktornotor

UEFI won't boot indeed. You need Secure Boot disabled and "legacy" mode on. How's it called depends on your BIOS vendor.

captain1980

I understand. But i put it on legacy mode "setting default for windows 7" thats the setting the vendor recommended for installing pfsense due to the booting from usb issue.

But now i am thinking can this setting causing my NIC assignment problem ? Should i go back on UEFI mode with some other tweaks.

Its like my system cannot differ the two onboard NICs

doktornotor

I have NFC what W7 has to do with BIOS settings, sorry. Read the motherboard manual.

DeLorean

If you use a USB 3.0 Memorystick, you can use the embedded version of pFsense.
Download the preferred image and extract it with 7zip.
Then use Win32 Disk Imager for extracting the .IMG file to your USB memorystick.
That's how i use pFsense for almost 8 months now.

Grtz
DeLorean

johnpoz

"Its like my system cannot differ the two onboard NICs"

Nonsense – more like your just assigning them wrong... What are their Macs? Set one to dhcp, the other lan - plug in and let get dhcp from your isp/router.. The other one is the lan..

captain1980

Hey guys….

Got it finally working. Before install i plugged in both network cables one from my moden and the lan. Power cycled my modem. On boot the WAN adress was present this time. Assigned the LAN ip, subnet and range etc. No problem getting to the web GUI.

Thanks for all your feedback and posts.

This thread can be set to solved/ close :)