Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    Lan Interface Stop responding and firewall need to be reboot

    Scheduled Pinned Locked Moved General pfSense Questions
    12 Posts 5 Posters 2.8k Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • D
      doktornotor Banned
      last edited by

      So you have gazillions errors there and wonder why does it stop responding? I'd say the HW is shit.

      1 Reply Last reply Reply Quote 0
      • A
        arbisoft
        last edited by

        Thanks for reply.
        I have changed the NIC adapters. Before It was Broadcom built in interface in server using it for lan interface. Now I add Intel PCI express card to server but facing the same issue.
        lan Interface stop functioning where there is high load of traffic.
        No error on WAN interfaces on same ports.

        1 Reply Last reply Reply Quote 0
        • D
          divsys
          last edited by

          Doesn't sound like a pfSense issue at this point.

          If you believe you've isolated out the NIC's as your possible hardware problem, now you get move on to the rest of your network.

          Your stuck troubleshooting on the LAN side - patch cables, your switch ports, the switch itself, the various LAN devices attached.

          -jfp

          1 Reply Last reply Reply Quote 0
          • A
            arbisoft
            last edited by

            lan interface is terminated at cisco switch 2950 on gig port with native vlan, all my lan devices dlink hubs(connected with end pc's), rukus wireless ap's are also connected with same switch. 
            Change patch cables ,checked with dlink switch between lan and cisco 2950 but no success, lan interface hangs shows in/out error and collision , box require reboot to work it again.
            If I replace the pf box with linux machine of nat router to share the internet for my nodes I can not see any error on its lan adapter.

            1 Reply Last reply Reply Quote 0
            • DerelictD
              Derelict LAYER 8 Netgate
              last edited by

              dlink hubs(connected with end pc's)

              Hubs?

              So you have one switch with a bunch of unmanaged consumer crap daisy-chained off it?

              Chattanooga, Tennessee, USA
              A comprehensive network diagram is worth 10,000 words and 15 conference calls.
              DO NOT set a source address/port in a port forward or firewall rule unless you KNOW you need it!
              Do Not Chat For Help! NO_WAN_EGRESS(TM)

              1 Reply Last reply Reply Quote 0
              • A
                arbisoft
                last edited by

                Yes, this is scenario and working for last 7 months without issue.
                I have just un-plugged all cables from switch , connect my machine with switch and flood the box lan ip with hping run on my system.
                interface status shows error
                In/out errors 28889/0

                1 Reply Last reply Reply Quote 0
                • DerelictD
                  Derelict LAYER 8 Netgate
                  last edited by

                  Guess you reached critical mass on your shitty network.

                  Chattanooga, Tennessee, USA
                  A comprehensive network diagram is worth 10,000 words and 15 conference calls.
                  DO NOT set a source address/port in a port forward or firewall rule unless you KNOW you need it!
                  Do Not Chat For Help! NO_WAN_EGRESS(TM)

                  1 Reply Last reply Reply Quote 0
                  • A
                    arbisoft
                    last edited by

                    Here is my  linux nat machine interface replaced with  pfsense , no error on interface even with flood hping.
                    eth1      Link encap:Ethernet  HWaddr 0c:54:a5:51:32:b2 
                              inet addr:x.x.x.x  Bcast:172.16.255.255  Mask:255.255.0.0
                              inet6 addr: fe80::e54:a5ff:fe51:32b2/64 Scope:Link
                              UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
                              RX packets:635836980 errors:0 dropped:431 overruns:0 frame:0
                              TX packets:460361724 errors:0 dropped:0 overruns:0 carrier:0
                              collisions:0 txqueuelen:1000
                              RX bytes:73792371229 (73.7 GB)  TX bytes:286723195687 (286.7 GB)
                    I have to work with same network for some time.
                    Is there a way to make my pf interface never goes down?

                    1 Reply Last reply Reply Quote 0
                    • DerelictD
                      Derelict LAYER 8 Netgate
                      last edited by

                      You need to find your layer 1 / layer 2 problem and everything will run fine.

                      Chattanooga, Tennessee, USA
                      A comprehensive network diagram is worth 10,000 words and 15 conference calls.
                      DO NOT set a source address/port in a port forward or firewall rule unless you KNOW you need it!
                      Do Not Chat For Help! NO_WAN_EGRESS(TM)

                      1 Reply Last reply Reply Quote 0
                      • A
                        arbisoft
                        last edited by

                        Thanks Derelict@Derelict:

                        You need to find your layer 1 / layer 2 problem and everything will run fine.

                        checking the switch config , I found errors on switch port attached with pf lan interface. After terminating lan interface to switch gig port and setting the duplex and speed solved the issue. Now it is working fine and vanished in/out error on interface.
                        :)

                        1 Reply Last reply Reply Quote 0
                        • M
                          MaxHeadroom
                          last edited by

                          Hi,

                          i had also equel problem but only with a slow, sometime broken connection to pfsense  WebGui from lan.
                          Suricata show me ACK missmatch and other crazy thinks.

                          My problem was a flapping WAN port .
                          Setting to 1GbitFD fixed on card and switch solved also my problem.

                          Maybe a bad cable but now it runs…

                          regards
                          max

                          1 Reply Last reply Reply Quote 0
                          • First post
                            Last post
                          Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.