Errors during pfSense boot
-
Hi Friends,
I'm starting test of the pfSense on RouterBoard 230r3 and, I observer some alerts (or errors) during first boot:
Copyright
1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE-p7 #0: Sat Sep 22 20:59:00 UTC 2007
root@fwdev.bluepex.com:/usr/obj.pfSense/usr/src/sys/pfSense_wrap.6
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Geode(TM) Integrated Processor by National Semi (266.71-MHz 586-class CPU)
Origin = "Geode by NSC" Id = 0x540 Stepping = 0
Features=0x808131 <fpu,tsc,msr,cx8,cmov,mmx>real memory = 134217728 (128 MB)
avail memory = 121876480 (116 MB)
wlan: mac acl policy registered
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
cpu0 on motherboard
pcib0: <host to="" pci="" bridge="">pcibus 0 on motherboard
pir0: <pci 6="" interrupt="" routing="" table:="" entries="">on motherboard
pci0: <pci bus="">on pcib0
sis0: <natsemi 10="" dp8381[56]="" 100basetx="">port 0x1000-0x10ff mem 0xfebf7000-0xfebf7fff irq 9 at device 11.0 on pci0
sis0: Silicon Revision: DP83816A
miibus0: <mii bus="">on sis0
ukphy0: <generic ieee="" 802.3u="" media="" interface="">on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: 00:0c:42:03:7f:eb
sis1: <natsemi 10="" dp8381[56]="" 100basetx="">port 0x1400-0x14ff mem 0xfebf8000-0xfebf8fff irq 10 at device 12.0 on pci0
sis1: Silicon Revision: DP83816A
miibus1: <mii bus="">on sis1
ukphy1: <generic ieee="" 802.3u="" media="" interface="">on miibus1
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis1: Ethernet address: 00:0c:42:03:7f:ec
cbb0: <ti1520 pci-cardbus="" bridge="">mem 0xfebf9000-0xfebf9fff irq 11 at device 13.0 on pci0
cardbus0: <cardbus bus="">on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb1: <ti1520 pci-cardbus="" bridge="">mem 0xfebfa000-0xfebfafff irq 11 at device 13.1 on pci0
cardbus1: <cardbus bus="">on cbb1
pccard1: <16-bit PCCard bus> on cbb1
Geode GPIO@ = 1c00
isab0: <pci-isa bridge="">port 0x1c00-0x1c3f,0x1c40-0x1c7f at device 18.0 on pci0
isa0: <isa bus="">on isab0
pci0: <bridge>at device 18.1 (no driver attached)
atapci0: <national geode="" sc1100="" ata33="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1cc0-0x1ccf at device 18.2 on pci0
ata0: <ata 0="" channel="">on atapci0
ata1: <ata 1="" channel="">on atapci0
pci0: <multimedia, audio="">at device 18.3 (no driver attached)
pci0: <display, vga="">at device 18.4 (no driver attached)
Geode CBA@ 0x9000
Geode rev: 06 03
Timecounter "Geode" frequency 27000000 Hz quality 1000
pci0: <bridge>at device 18.5 (no driver attached)
ohci0: <ohci (generic)="" usb="" controller="">mem 0xfebff000-0xfebfffff irq 12 at device 19.0 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: <ohci (generic)="" usb="" controller="">on ohci0
usb0: USB revision 1.0
uhub0: (0x0e11) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ppc0: parallel port not found.
sio0 at port 0x3f8-0x3ff irq 4 flags 0x30 on isa0
sio0: type 16550A, console
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
RTC BIOS diagnostic error 51 <rom_cksum,memory_size>Timecounters tick every 10.000 msec
Fast IPsec: Initialized Security Association Processing.
ad0: FAILURE - SETFEATURES SET TRANSFER MODE status=51 <ready,dsc,error>error=4<aborted></aborted></ready,dsc,error>
ad0: 122MB <hitachi flash="" card="" rev="" 3.0="">at ata0-master BIOSPIO
GEOM_LABEL: Label for provider ad0a is ufs/pfSense.
GEOM_LABEL: Label for provider ad0d is ufs/pfSenseCfg.
Trying to mount root from ufs:/dev/ufs/pfSense___
/ f
/ p _/ Sense
_/
__/Welcome to pfSense 1.2-RC2 on the 'embedded' platform…
Setting up embedded specific environment... done.
Mounting filesystems... done.
Creating symlinks......done.
Launching PHP init system... done.
Initializing.................. done.
Starting device manager (devd)...done.
Loading configuration......done.
Updating configuration...done.
Cleaning backup cache...done.
Setting up extended sysctls...done.
Syncing user passwords...done.
Starting Secure Shell Services...done.
Setting timezone...done.
Starting syslog...done.
Configuring LAN interface...done.
Configuring WAN interface...done.
Configuring OPT interfaces...done.
Configuring CARP interfaces...done.
Syncing system time before startup...done.
Configuring firewall…ipfw: rule 2: setsockopt(IP_FW_DEL): Invalid argument
ipfw: rule 3: setsockopt(IP_FW_DEL): Invalid argument
…done.
Starting webConfigurator...done.
Starting DNS forwarder...done.
Setting up microcode and tx/rx offloading...done.
Configuring IPsec VPN... done
Starting FTP helpers...done.
Waiting for final CARP interface bringup........................................... done.
done.
Generating RRD graphs...done.
Starting OpenNTP time client...done.
Starting CRON... done.
Executing rc.d items...
Starting /usr/local/etc/rc.d/*.sh...done.
appending output to nohup.out
Bootup completeI analyze boot process and firewall rules but no found errors or inconsistence.
How cal solve this problems?
Regards.
[]s</hitachi></rom_cksum,memory_size></ohci></ohci></bridge></display,></multimedia,></ata></ata></national></bridge></isa></pci-isa></cardbus></ti1520></cardbus></ti1520></generic></mii></natsemi></generic></mii></natsemi></pci></pci></host></fpu,tsc,msr,cx8,cmov,mmx>
-
the kernel tries to set transfer based on a weird guess :P check the BIOS settings for the drives, switch off DMA if on, turn on a lower PIO mode and try to reboot?