Site2site all traffic is ok except for http/https

muswellhillbilly

Do you mean you can't access anything on ports 80 or 443 across the connection or that it's just the access points which aren't responding? Do you have any web servers at either end you can test with?

van1985

i have the same trouble.
PfSense(192.168.106) - ipsec - D-link DFL 860 E(192.168.100)

trying to open http web page of printer (192.168.100.52) from PfSense Lan network(192.168.106.10).
web page is loading… and nothing happends.

all other traffic is ok ( RDP , smb Share, SIP )

If disable Firewall (System: Advanced: Firewall and NAT) , the page will open...

Dropping rule: @5(1000000103) block drop in log inet all label "Default deny rule IPv4"

FirewallRules_IpSec.jpg_thumb

FirewallRules_Lan.jpg_thumb

FirewallLog.jpg_thumb

Firefox.jpg_thumb

koeievanger

yes exaclty the same problem.

no one has some ideas?

koeievanger

nobody?

MaxHeadroom

Try to lower the ipsec Advance Setting

"Enable MSS clamping on VPN traffic"

Maybe that help's

Do you have installed a add package ?

regards

max

teladero

It is so weird that you are having the same issue as me. Every other type of traffic is fine. I get an error page saying that it timed out after 60 seconds. I don't actually see anything in the firewall log. The IPSec log is saying that it is sending packets (no surprise there), but nothing too helpful.

Does anyone have an idea on this?

Derelict

My guess would be default gateways on the devices you cannot manage not being pointed at pfSense.

Most dumb consumer routers don't support a default gateway when used as an AP connected to its LAN only, etc.

But if you can ping 192.168.100.52 from the other side just not open its web interface, it's not routing.

van1985

@MaxHeadroom:

Try to lower the ipsec Advance Setting

"Enable MSS clamping on VPN traffic"

Yes! It's work!
Enabling this option without any parametr solved my problem
Thanks!

Derelict

So what does that do? Anyone? And what was the issue?

MaxHeadroom

"Enable MSS clamping on VPN traffic" is for lowering the maximum payload in a tcp segment.

In Ipsec a fragmented packet makes problems so you have to be shure that the MTU size fits you internet connection.
(Especial with pppoe MTU size is lower there )

MSS -> Maximum Segment Size

teladero

@van1985:

@MaxHeadroom:

Try to lower the ipsec Advance Setting

"Enable MSS clamping on VPN traffic"

Yes! It's work!
Enabling this option without any parametr solved my problem
Thanks!

I tried leaving it by the default settings and it did not solve my problem. Here's another weird thing, I have a synology NAS which I manage through its web interface at https://ipaddress:35909. I can access that from across the IPsec tunnel, but not plain Jane https. My remote site is using pfsense and on the LAN interface (where I am doing all the testing from). My rules allow the LAN to access anything and everything.

Anybody know what might be my problem?

Thanks!

MaxHeadroom

Hi teladero

Why not lowering the MSS ? what is your problem with the webgui ? Maybe the NAS Gui allow only acces from LAN

If you want access the NAS over internet behind a pfsense you have to add a Firewall: NAT: Port Forward for the
Nas

Please be more clear with your request.

regard max

koeievanger

fantastic, i also solved this by enabling the MSS clamping :)

THX

teladero

@MaxHeadroom:

Hi teladero

Why not lowering the MSS ? what is your problem with the webgui ? Maybe the NAS Gui allow only acces from LAN

If you want access the NAS over internet behind a pfsense you have to add a Firewall: NAT: Port Forward for the
Nas

Please be more clear with your request.

regard max

What should I lower it to?

I have had a site to site VPN up before with two Meraki security appliance. It worked beautifully.

I do not want my NAS to be accessible through port forwarding. Sorry I wasn't more clear.

teladero

@MaxHeadroom:

Hi teladero

Why not lowering the MSS ? what is your problem with the webgui ? Maybe the NAS Gui allow only acces from LAN

If you want access the NAS over internet behind a pfsense you have to add a Firewall: NAT: Port Forward for the
Nas

Please be more clear with your request.

regard max

I noticed that the default size was 1400, so I tried 1300 and that did not work. Should I just go smaller? If so, am I slowing my connection to the remote network?

Thanks for all your help.

MaxHeadroom

No connection is not faster ;D

(I think the nas is blocking the ip…hard to guess)

regards
max

teladero

@MaxHeadroom:

No connection is not faster ;D

(I think the nas is blocking the ip…hard to guess)

regards
max

The NAS (or any other device on my remote network) is not blocking http or https traffic. It used to work fine when I was on a meraki site-to-site vpn. Nothing has changed here except going to pfsense at one location. I can ping, do samba shares, remote desktop, etc across the vpn, so I know it is established. I can try and add some rules on the pfsense box to allow http traffic explicitly over the vpn. I will post the results.

teladero

@MaxHeadroom:

No connection is not faster ;D

(I think the nas is blocking the ip…hard to guess)

regards
max

I can't believe it…I added a rule to allow any traffic to the remote network, and it worked! The most bizarre thing is that you can clearly see the two rules below it, allowing IPv4 and IPv6 traffic sourced from the LAN to anywhere. No clue why this was necessary, but hopefully it will help someone else in my position.

Thanks again MaxHeadroom!

Capture.PNG_thumb

Derelict

That makes zero sense. What are the advanced characteristics on that second rule?

teladero

@Derelict:

That makes zero sense. What are the advanced characteristics on that second rule?

Makes zero sense to me as well. Here's what I have for advanced settings.

Capture.PNG_thumb