Is it possible to set up a console over USB serial?
-
Yes, i use that setup on my pfsense box in my signature.
Serial console allows you to access the terminal before ssh and see the full boot process /debug if needed.
I assume that you are using a "real serial port" is on the pfSense box, and the USB is on the machine you are using for management correct?
I don't know a lot about either FreeBSD or USB, but from what I have read (and may or may not have understood or remembered correctly), a "Real Serial Port", is (or at least can be) interrrupt driven I/O, but a USB serial is polled I/O (Am I correct???). Is that going to work with pfSense (FreeBSD)?
Yes, I am using real serial port on my pfSense box (RS232) with a RS232 to USB adapter to a raspberry Pi.
I am not sure if a usb serial device will work via FreeBSD.
-
Unfortunately I don't have a USB port on my pfSense box, so I don't have a choice. I wonder if there is anyone here who knows FreeBSD well enough to know if it is possible or not.
-
Unfortunately I don't have a USB port on my pfSense box, so I don't have a choice. I wonder if there is anyone here who knows FreeBSD well enough to know if it is possible or not.
I did some more research on this….. I don't think the console will work over usb
-
Thanks… I was afraid of that.
-
You can still use telnet or ssh to monitor your console, once your pfSense has booted up.
-
You can still use telnet or ssh to monitor your console, once your pfSense has booted up.
Thanks, yes I do that now… was just hoping not to have to pull a monitor off a PC to watch the FW boot. Not the end of the world, don't have to boot very often, and as long as it boots within 2-3 minutes, I likely don't really need to see it live, I can just dmesg.
-
…hoping not to have to pull a monitor off a PC to watch the FW boot...
Still 2 possibilities.
a) Get a streaming device that converts your VGA to an IP stream to be viewed with any streaming receiver OR
b) look at your motherboard and find out what the white pin header at bottom center is. (see pic attached) Could be a serial port.
-
…hoping not to have to pull a monitor off a PC to watch the FW boot...
Still 2 possibilities.
a) Get a streaming device that converts your VGA to an IP stream to be viewed with any streaming receiver OR
b) look at your motherboard and find out what the white pin header at bottom center is. (see pic attached) Could be a serial port.Thanks for the reply… Can't cost justify a)... likely cheaper to upgrade from a 4 to 8 port KVM switch.
b) is a possibility... not sure how I would do it though, or how I would work out the mechanics of an external connection without making the box look like a piece of crap.Open to suggestions. For now, I'll run it headless as long as it boots OK, and if it hangs for any reason, I'll have to pull the KVM leads off another box. I might consider the serial mods on my FreeNAS box, it has a real serial port... then I have a spare KVM port.
-
…the mechanics of an external connection without making the box look like a piece of crap...
Come on!
There are two (unused ?!!) holes for wireless antennas already in the box. Use a 3,5mm jack and install it in one of them. All you need are 3 pins for TX, RX and GND and a custom cable with a 3,5mm stereo connector to a db9 plug.Or wire the db9 socket with 2m of small cable directly through the hole. I use small diameter AES/EBU microphone cables for that (2 leads and 1 screen). Done.
Something like that:
https://www.amazon.com/24AWG-Extra-Digital-Audio-Cable/dp/B00HRO5A02/ref=sr_1_13?ie=UTF8&qid=1470139237&sr=8-13&keywords=24AWG+AES%2FEBU+cable
Your local music store is happy to help you with that. -
Good point… I've been staring at the port side of the box because of where it's mounted, so I forgot about those holes, so I could see possibly doing that.
Only thing is, if that is a serial port, wouldn't it show in dmesg? I don't have the FreeBSD background to know how to probe for the UART.
So before cracking open the case and risking physical damage I would want to:
Step 1: Detect the presence of a UART though software to determine if it exists and what it's hardware is.
Step 2: Determine if there is a driver for that hardware, and if it needs CTS/RTS flow control to operate.If I get though 1 & 2, then I'd do a test with the box open, and if that passed, I'd worry about making it pretty, but unless I get 1 and 2 figured out first, don't want to put the effort into the physical stuff.
**An aside:
Also, how to you reassemble the unit. I looked inside when I installed memory and SSD, and that heat sink arrangement looked pretty scary to put back together if the motherboard was removed. **BTW… does your original image file have higher resolution of the components around that connector? When I looked at it, my first guess was that it was power to support a SATA device plugged into the SATA port.
-
… does your original image file have higher resolution...
Me?
That's a picture from the Amazon article description. I don't know more about that unit than what's written here or there. I don't have one. -
Good point… I've been staring at the port side of the box because of where it's mounted, so I forgot about those holes, so I could see possibly doing that.
Only thing is, if that is a serial port, wouldn't it show in dmesg? I don't have the FreeBSD background to know how to probe for the UART.
So before cracking open the case and risking physical damage I would want to:
Step 1: Detect the presence of a UART though software to determine if it exists and what it's hardware is.
Step 2: Determine if there is a driver for that hardware, and if it needs CTS/RTS flow control to operate.If I get though 1 & 2, then I'd do a test with the box open, and if that passed, I'd worry about making it pretty, but unless I get 1 and 2 figured out first, don't want to put the effort into the physical stuff.
**An aside:
Also, how to you reassemble the unit. I looked inside when I installed memory and SSD, and that heat sink arrangement looked pretty scary to put back together if the motherboard was removed. **BTW… does your original image file have higher resolution of the components around that connector? When I looked at it, my first guess was that it was power to support a SATA device plugged into the SATA port.
I think your best bet is to switch one of your 8 KVM devices to use the serial console and change your pfSense box to that open KVM connection.
I agree that we should be seeing the serial port show up in dmesg if it was detected on the motherboard. Do you have any serial or com port settings in the BIOS?
I also agree that putting this machine back together may be difficult with the heatsink
