PfSense does not get an IPv6 address on WAN

flat_eric1

Hi!

This might be the case - but this does not explain that I do not get an IPv6 address at all. So my first humble wish is to get an IP address everytime I boot the box or I toggle WAN interface.
When this is fixed, I will try to get a prefix and pass addresses to my LAN network :)

The problem here seems to be that dhcp6c does not start automatically, neither on boot time nor at WAN activation. If I did not start dhcp6c manually (which gives me an IPv6 address immediately on WAN), I would never get an IPv6 address.

So the basic question is: why does dhcp6c not start e.g. at boot time? Are there logs that I could take a look at to debug this?

mkapalla

So I have exactly the same problem.

pfSense doesn't get an IP and the support of "Deutsche Glasfaser" is too dumb to give me details on the IPv6 configuration.

Maps

After 3 Nights testing, "Deutsche Glasfaser" work for me, now for one day
Only one Problem left. After Reboot, I have to wait for get a ipv4 then login in by ssh
killall -9 dhcp6c
dhcp6c -c /var/etc/dhcp6c_wan.conf -d igb0
After done i have a ipv6 , with tracking interface on Lan I am able to advice ipv6 to clients by dhcpv6.
Wan Prefix is set to /56 and lan to /64, get prefix over ipv4 is off.

Pfsense 2.3.2 p1

m0nji

@Maps:

After 3 Nights testing, "Deutsche Glasfaser" work for me, now for one day

do you use DHCP6 on WAN interface or SLAAC? any other advanced settings?

Maps

DHCPv6 Assistend
::1000 to ::2000 in IPadress pool.
Both work linux with SLAAC and mac with DHCPV6 .
Leases with DHCPV6 are displayed.
But I can´t assign a fix adress to a device. Any Idea.

mkapalla

Today I got a brouchure from "Deutsche Glasfaser", which says DHCP (for IPv4), IPv6rd and IPv4/IPv6 has to be supported by the router.

Does that mean I should try the 6rd Tunnel or 4to6 Tunnel on WAN?

EDIT: Tried that and shit's not working.
I don't have the configuration details for 6rd…

Here are a few informations:

https://www.deutsche-glasfaser.de/fileadmin/Content/Pdf/Downloads/Anleitungen/Genexis_Live__mit_eigenem_Router_anschliessen.pdf
https://www.flink-glasfaser.de/fileadmin/pdfs_flk/20160831_DG_Schnittstellenspezifikation_final_online.pdf
https://www.new.de/fileadmin/user_upload/new.de/Dokumente/Glasfaser/NEW_Glasfaser_Leistungsbeschreibung.pdf
http://glasfaser-haltern.de/images/DGhome_Leistungsbeschreibung.pdf

JKnott

Does that mean I should try the 6rd Tunnel or 4to6 Tunnel on WAN?

I would suspect that brochure is a bit out of date. If they are providing native IPv6, as reported by Maps, there is no need of a tunnel, which is what 6rd and 6to4 are. My own ISP also provided tunnels, but have had native IPv6 since about April.

Maps

My Setup:
WAN:
DHCP
DHCP6
Emtpy MAC/MTU/MSS
No Options DHCP Client
DHCPv6 Client
Only 56 Prefix and prefix Hint

Both Block off.

LAN:
Static ipv4
Track Interface
No MTU ..

Track IPV6:
WAN
ID 1
No Blocks

DHCP V6 RA
Sever
Range.
::1000 ::2000
64 Prefix

RA:
Assisted
High
Rest empty.

State now : IPv6 is running.

flat_eric1

Hi all!

@mkapalla: The brochures state that there is an IPv4/IPv6 dual stack and IPv6rd, so the tunnel probably is not the preferred way to use IPv6 with Deutsche Glasfaser (So I agree with JKnott). They definitively provide native IPv6 addresses.
@Maps: Thanks for sharing your configuration with us, highly appreciated.

This thread was about the fact that dhcp6c does not start correctly or not at all at system start or interface activation, so I would like to keep the topic here and would suggest that you start a thread with a headline describing your issue. I guess chances will be better to get your issues solved if the headline of the thread matches the content.

So does anybody have any hints?

bimmerdriver

As I said above, a possible cause for dhcp6c not starting is because pfsense is waiting for the edge router to respond with RA. pfsense will wait forever for the RA and will not start dhcp6c. ipv6 will not work at all. If you're not sure whether your isp edge router requires a dhcp6 solicit before it will respond to an RS, download the 2.4 development snapshot and configure the wan with "do not wait for RA". If that doesn't solve your problem, maybe someone else has another idea.

Maps

Where did I found a nano version from 2.4 ? Or does the memstick version works too with the SD card in my Alex app ?

Maps

I saw NanoBSD is not supported on 2.4.
What did the RA don´t wait done ? Is it only web path and i am able to do it in a config file by hand or a dhcp6c path ?

Offtopic @ other "Deutsche Glasfaser" user. What is your plan to apply the Telefon functions ? sipproxy, asterisk on pfsense ?

bimmerdriver

@Maps:

What did the RA don´t wait done ? Is it only web path and i am able to do it in a config file by hand or a dhcp6c path ?

Normally when pfsense starts, it sends an RS, waiting for an RA, then when the RA is received, it starts dhcp6c. Some ISPs have configured their edge routers to not respond to an RS until after a dhcp solicit is received. In that case, there is a deadlock causing dhcp6c to never start. If you can get a prefix by manually starting dhcp6c, it's an indication that this may be happening. The feature is enabled using the webgui in the wan settings, but it's only available in 2.4. (There were some patches to 2.3, but not sure if they are compatible with 2.3.2_1.)

Guest

Just install the 2.3 development version, it's working fine. All the additions for Don't wait for RA have been included.

Maps

I can confirm, with don´t wait RA, in the 2.3 Dev Release I got the IPV6 network IP on WAN.

Guest

@Maps:

I can confirm, with don´t wait RA, in the 2.3 Dev Release I got the IPV6 network IP on WAN.

Good news.

I stopped updating the patches months ago when it was included in the 2.3 dev versions and I never got around to writing them for earlier releases.

Maps

I think there is a small issue in the fix.
When I had change the settings in the lan interface, the system will save and apply the setting,then the ipv6 will not come back.
When I release the Wan IP and renew it with the gui the IPV6 Net will come back.

It is possible , in this case the RA settings will not be used ?

Guest

@Maps:

I think there is a small issue in the fix.
When I had change the settings in the lan interface, the system will save and apply the setting,then the ipv6 will not come back.
When I release the Wan IP and renew it with the gui the IPV6 Net will come back.

It is possible , in this case the RA settings will not be used ?

No there is no issue with the fix. When you take down the LAN interface you clear it, the IPv6 address and PD is created by the script that runs when the WAN interface goes online. You just need to be aware of the way that prefix delegation works. If you left it long enough then I suspect that the dhcp6 time would expire and then refresh, giving you an address and prefix again; of course how long you would need to wait depends on your ISP and the lease renewal interval, mine is 30 minutes but others could be a day or two or even longer.

bimmerdriver

There is a small issue with the fix, but it's different from what was described. If you release the WAN interface then watch the "gateways status" on the dashboard, the WAN_DHCP status will go offline, but the WAN_DHCP6 status will stay online. If you leave it like this (i.e., if you don't renew the WAN interface), eventually, the WAN_DHCP6 status will go offline. This problem wasn't always there. It was introduced when another issue relating to the startup and shutdown of other dhcp processes was fixed. It's not a show stopper, but something seems to not be working properly. Refer to https://redmine.pfsense.org/issues/5993.

Guest

@bimmerdriver:

There is a small issue with the fix, but it's different from what was described. If you release the WAN interface then watch the "gateways status" on the dashboard, the WAN_DHCP status will go offline, but the WAN_DHCP6 status will stay online. If you leave it like this (i.e., if you don't renew the WAN interface), eventually, the WAN_DHCP6 status will go offline. This problem wasn't always there. It was introduced when another issue relating to the startup and shutdown of other dhcp processes was fixed. It's not a show stopper, but something seems to not be working properly. Refer to https://redmine.pfsense.org/issues/5993.

I've not been looking at this thread or the 5993 issue for months, I've been a bit busy with real work. :)

Couple of questions, does dhcp6c shutdown on WAN release and does dpinger shut down also?

I think I know why this isn't high on the list of things to fix, you are unlikely to run pfSense without the WAN interface online, it serves no purpose and I tend to make any changes required, which are few and rare and then reboot.