[solved] PPPoE IA-PD woes

maverick_slo

Yeah link flap for 10 seconds or less is ok… As soon as last lcp is missed and pppoe starts reconnecting if I then plug utp back in no ipv6 address on pppoe...
How do I run rtsold script from shell?
Will try it in hour or 2 when I come home...

@maverick_slo:

Yeah link flap for 10 seconds or less is ok… As soon as last lcp is missed and pppoe starts reconnecting if I then plug utp back in no ipv6 address on pppoe...
How do I run rtsold script from shell?
Will try it in hour or 2 when I come home...

In /Var/etc you should see a script something like rtsold_{IFACE}_script.sh, where {IFACE} is the interface you are interested in.

To run it, just do ./ rtsold_{IFACE}_script.sh

I'll squash down those commits it's getting untidy.

OK, I've squashed all those commits down to a single pair.

718cbc2d3921627e9767e59d539386c843dffcc4 - Reasons
07c304a5593e4fc7d574964bbf3641f92c16d8fa - Wan flap

maverick_slo

When I run rtsold script:

Mar 12 13:15:49 	php-fpm 	72012 	/rc.newwanipv6: rc.newwanipv6: No IPv6 address found for interface PPPOE [opt2].
Mar 12 13:15:49 	php-fpm 	72012 	/rc.newwanipv6: rc.newwanipv6: Info: starting on pppoe0.
Mar 12 13:15:49 	php-fpm 	75079 	/rc.filter_configure_sync: Gateways status could not be determined, considering all as up/active. (Group: GWGRP_IPv6)
Mar 12 13:15:47 	rtsold 		RTSOLD Lock in place - sending SIGHUP to dhcp6c
Mar 12 13:15:47 	rtsold 		Received RA specifying route for interface opt2(pppoe0)

So still no IPv6 address on iface PPPOE.
Weird.

maverick_slo

I think it will only get ipv6 address when connecting and no later…

Only thing that is 1000% is disconnect/connect from interfaces page or save/apply on pppoe iface settings page.
In those 2 cases ipv6 is ALWAYS assigned.

Yes, I was doing a bit of reading, think it's a pppoe thing - note my earlier comment about changing ISP, I'll find out soon!

Just remembered, my current ISP is a little wierd in that respect too, if I don't send a dhcp6 solict within a set period after a v4 solicit then no ipv6. The v4 solicit also contains the credentials so the only solution is drop the link, wait 5 minutes until the ISP's BNG resets and start the login again.

maverick_slo

Ahh we just both posted at the same time :)

See above I`ve edited post…

Yeah, this is pppoe thingie I think that too...

PPPoE is really tricky sometimes...

But you`ve fixed flapping issue thanks a bunch!!

Good. Would you like to roll back the patches and apply the consolidated pair and see if it's OK. I can then comment on that PR that at least one person has tested it and it's OK.

maverick_slo

I already did that and using it
Works great.

Another happy customer! 8)

hda

@marjohn56:

Good. Would you like to roll back the patches and apply the consolidated pair and see if it's OK. I can then comment on that PR that at least one person has tested it and it's OK.

2.4.0-BETA (amd64)
built on Wed Mar 15 18:17:17 CDT 2017
FreeBSD 11.0-RELEASE-p8

Redmine #7330 / PR #3515. Tested 5 sec. unplug then insert of WAN side.
Result OK. Thanks again.