FW-7541D wrong temperature
-
dev.cpu.3.temperature: 9.0C dev.cpu.3.coretemp.throttle_log: 0 dev.cpu.3.coretemp.tjmax: 100.0C dev.cpu.3.coretemp.resolution: 1 dev.cpu.3.coretemp.delta: 91 dev.cpu.3.cx_usage: 100.00% last 4183us dev.cpu.3.cx_lowest: C1 dev.cpu.3.cx_supported: C1/1/0 dev.cpu.3.%parent: acpi0 dev.cpu.3.%pnpinfo: _HID=none _UID=0 dev.cpu.3.%location: handle=\_PR_.P004 dev.cpu.3.%driver: cpu dev.cpu.3.%desc: ACPI CPU dev.cpu.2.temperature: 9.0C dev.cpu.2.coretemp.throttle_log: 0 dev.cpu.2.coretemp.tjmax: 100.0C dev.cpu.2.coretemp.resolution: 1 dev.cpu.2.coretemp.delta: 91 dev.cpu.2.cx_usage: 100.00% last 179us dev.cpu.2.cx_lowest: C1 dev.cpu.2.cx_supported: C1/1/0 dev.cpu.2.%parent: acpi0 dev.cpu.2.%pnpinfo: _HID=none _UID=0 dev.cpu.2.%location: handle=\_PR_.P003 dev.cpu.2.%driver: cpu dev.cpu.2.%desc: ACPI CPU dev.cpu.1.temperature: -1 dev.cpu.1.coretemp.throttle_log: 0 dev.cpu.1.coretemp.tjmax: -1 dev.cpu.1.coretemp.resolution: -1 dev.cpu.1.coretemp.delta: -1 dev.cpu.1.cx_usage: 100.00% last 4288us dev.cpu.1.cx_lowest: C1 dev.cpu.1.cx_supported: C1/1/0 dev.cpu.1.%parent: acpi0 dev.cpu.1.%pnpinfo: _HID=none _UID=0 dev.cpu.1.%location: handle=\_PR_.P002 dev.cpu.1.%driver: cpu dev.cpu.1.%desc: ACPI CPU dev.cpu.0.temperature: -1 dev.cpu.0.coretemp.throttle_log: 0 dev.cpu.0.coretemp.tjmax: -1 dev.cpu.0.coretemp.resolution: -1 dev.cpu.0.coretemp.delta: -1 dev.cpu.0.cx_usage: 100.00% last 193us dev.cpu.0.cx_lowest: C1 dev.cpu.0.cx_supported: C1/1/0 dev.cpu.0.%parent: acpi0 dev.cpu.0.%pnpinfo: _HID=none _UID=0 dev.cpu.0.%location: handle=\_PR_.P001 dev.cpu.0.%driver: cpu dev.cpu.0.%desc: ACPI CPU dev.cpu.%parent:Strange, isn't it …
Thomas
-
???
Yeah, what's going on there… Are you sure it's actually a D525?
Steve
-
I hope so …
CPU Type: Intel(R) Atom(TM) CPU D525 @ 1.80GHz 4 CPUs: 1 package(s) x 2 core(s) x 2 HTT threadsLanner's recommendation was to install lm-sensors and the sent me a config file for this (see sensors3.conf).
Thomas
-
I hope so …
CPU Type: Intel(R) Atom(TM) CPU D525 @ 1.80GHz 4 CPUs: 1 package(s) x 2 core(s) x 2 HTT threadsLanner's recommendation was to install lm-sensors and the sent me a config file for this (see sensors3.conf).
Thomas
I also have a FW-7541D, but running Linux, and the "coretemp" module does not work properly with Linux on that box, which I presume is basically what FreeBSD/pfSense uses. With "coretemp" I get:
coretemp-isa-0000 Adapter: ISA adapter Core 0: +8.0 C (crit = +100.0 C) Core 1: N/A (crit = +100.0 C)It would seem using lm-sensors is the only way to to get the temperature, which does work properly.
-
Is it possible to run lm-sensor on FreeBSD/pfSense?
Thomas
-
No, there is no lmsensors in FreeBSD.
The closest thing is mbmon.
You would have to manually install that thoughSteve
-
Do you thing, that mbmon will work. How can I read then the temperature - only via ssh or also on the dashboard?
How can I install mbmon?
Thomas
-
You can try:
pkg add http://pkg.freebsd.org/FreeBSD:10:amd64/release_3/All/xmbmon-205_14.txzthen
rehashthen
mbmon -DBut installing FreeBSD packages isn't recommended.
Steve
-
I there any risk if i install the package?
How can I deinstall the package restless?
Thomas
-
I installed it on my D525 box here and there was no issue. It did't find any hardware though.
You can remove it with 'pkg delete X' if you need to.
You could just carry on without knowing the exact temperature though. It's probably not important. ;)
Steve
-
mbmon -D
Probe Request: none >>> Testing Reg's at ISA-IO <<< [ISA Port IO-Base:0x290] Probing Winbond/Asus/LM78/79 chip: CR40:0xFF, CR41:0xFF, CR42:0xFF, CR43:0xFF CR44:0xFF, CR45:0xFF, CR46:0xFF, CR47:0xFF CR48:0xFF, CR49:0xFF, CR4A:0xFF, CR4B:0xFF CR4C:0xFF, CR4D:0xFF, CR4E:0xFF, CR4F:0xFF CR56:0xFF, CR58:0xFF, CR59:0xFF, CR5D:0xFF CR3E:0xFF, CR13:0xFF, CR17:0xFF, CRA1:0xFF CR20:0xFF, CR22:0xFF, CR23:0xFF, CR24:0xFF CR27:0xFF, CR29:0xFF, CR2A:0xFF, CR2B:0xFF No Hardware Monitor found!! InitMBInfo: No such file or directoryAnd now?
Thomas
-
Use a thermometer? :P
I'm out of suggestions at this point.
Steve
