How to get Huawei E3372 working with pfSense?
-
If you have any luck, then please post your findings here.
-
I would try the rndis with E3372 and pfSense, but did not find any information to install the rndis (or urndis) kernel module.
Can you please point me to some information about doing that?Download the equivalent FreeBSD ISO for the pfSense version you're running. FreeBSD 10.3 for pfSense 2.3.4. Probably 64bit.
Extract the if_urndis.ko module from the ISO. Copy it to /boot/modules in pfSense and make the file executable.
Add the following line to /boot/loader.conf.local to load it at boot, create that file if you don't have one yet:
if_urndis_load="yes"Steve
-
i found that this is due to /usr/local/bin/3gstats.php holding open the cuaU0.3 device which stops it from clearing and being available when the usb is plugged in again. ssh'ing into pfsense, killing it, then replugging the device then works perfectly.
it seems that /usr/local/bin/3gstats.php should be listening for HANGUP and then exiting when received, observe how the 'cu' command exits gracefully if youre connected to the cuauU0.X and you pull out the USB.
this should be raised as a bug. where is the best place to raise it?
any annoying side note not specific to just the e3372, is that if the usb modem is unplugged then reconnected or rebooted (via AT commands) it comes up as ttyU1 then ttyU2 etc then pfsense config cant reconnect
ttyU0.{0,1,2} all disappear but ttyU0.3 remains. i think this is why the kernel gives it the next ttyU spot
fstat shows nothing is using ttyU0.3, but a reboot of pfsense is required to get the usb modem back to ttyU0
the result of the above is that pfsense is configured for ttyU0 it cannot reconnect and must be reconfigured (which breaks again on reboot) or rebooted.
-
Mmm, good catch.
Open it as a new bug on our redmine as with all bugs: https://redmine.pfsense.org/
Thanks,
Steve -
Done. See https://redmine.pfsense.org/issues/7653
-
Download the equivalent FreeBSD ISO for the pfSense version you're running. FreeBSD 10.3 for pfSense 2.3.4. Probably 64bit.
Extract the if_urndis.ko module from the ISO. Copy it to /boot/modules in pfSense and make the file executable.
Add the following line to /boot/loader.conf.local to load it at boot, create that file if you don't have one yet:
if_urndis_load="yes"Steve
I've been away from this forum for a few months and just came across your post following a Google search.
I have FreeBSD 11.0-RELEASE installed and looked for this module but couldn't find it…
My immediate aim is to turn a laptop into a WWAN-WLAN router using this Huawei E3372 modem which I have only ever managed to get working under Windows. -
using the modem in serial mode is probably your best bet for now.
-
using the modem in serial mode is probably your best bet for now.
I can figure out how…
I know I'm supposed to use usb_modeswitch but I haven't found the correct options to use, there are quite a few available.
-
you can set the E3772 so that it starts up in tty mode and usbmodeswitch isnt needed. infact all huawei modems have this features.
check out the post above where i step through how to flash the firmware and put into serial only mode: https://forum.pfsense.org/index.php?topic=88356.msg711074#msg711074
-
you can set the E3772 so that it starts up in tty mode and usbmodeswitch isnt needed. infact all huawei modems have this features.
check out the post above where i step through how to flash the firmware and put into serial only mode: https://forum.pfsense.org/index.php?topic=88356.msg711074#msg711074
I read through but couldn't make much sense of it…
Notice anything here: ?
What worked for me was a combination of steps from these two pages
http://www.0xf8.org/2017/01/flashing-a-huawei-e3372h-4g-lte-stick-from-hilink-to-stick-mode/
http://www.0xf8.org/2017/01/flashing-a-huawei-e3372h-4g-lte-stick-from-hilink-to-stick-mode/
I still haven't found out how to tell if I have “Hilink” firmware or “Stick” firmware…
-
despite double posting the same link, it explains how to determine your firmware.
i think the second link was supposed to be http://blog.asiantuntijakaveri.fi/2015/07/convert-huawei-e3372h-153-from.html
anyway, there are plenty of guides around to flash the firmware, just google for them.
there are also forums that can help.
but if youre uncomfortable opening up the modem and shorting pins, its probably something you should ask someone else to do for you
-
if youre interested, i can cook one up and ship it to you. or you can send me yours and i can do it.
-
Is there no way to get this working in hilink mode?
-
its just a matter of the kernel supporting it, and you being ok with the usb modem NAT'ing in front of you.
what would be ideal is NCM mode working properly
-
its just a matter of the kernel supporting it, and you being ok with the usb modem NAT'ing in front of you.
what would be ideal is NCM mode working properly
yeah, I agree that would be the best solution, but will the hilink mode be working if i load the if_urndis module, or do I need an other module? The NATing is fine in the setup that i'm doing this time.
-
I have no idea. I need the IP address for what im doing.
-
Just wondered if anyone has managed to get the Huawei E3372 working in RNDIS mode yet…
-
@balanga
See this thread here ;
https://forum.netgate.com/topic/130040/how-to-configure-rndis-on-e3372/17
I've managed to get it working and theres a little guide for you to work with-D
-
@stephenw10 said in How to get Huawei E3372 working with pfSense?:
Nice work. :)
FreeBSD does have an rndis driver now. It's not included in pfSense by default (yet) but you can load the module to test it if required.
Steve
Hi , I got my e3372 and switch it in stick mode.my problem is I've got a pfsense 2.3.5 on my alix 2d13 board..It doesnt show the NCM interface..How can I load rndis driver on 2.3.5??
