Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    Watchguard XTM 5 Series

    Scheduled Pinned Locked Moved Hardware
    1.1k Posts 130 Posters 1.4m Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • B
      Billyboy
      last edited by

      This happens to both boxes on all em Ports.  :(

      1 Reply Last reply Reply Quote 0
      • stephenw10S
        stephenw10 Netgate Administrator
        last edited by

        Hmm, and you're actually pulling the cable from the port on the xtm5?

        What does ifconfig show for that port during that time?

        Steve

        1 Reply Last reply Reply Quote 0
        • S
          Smoothrunnings
          last edited by

          On the WatchGuard XTM 5 motherboard do any of the pin-outs and or sockets support a VGA connector?

          I have been looking on Google but nothing I see points to anyone investigating if a VGA connector can be connected to the motherboard or not.

          Thanks,

          1 Reply Last reply Reply Quote 0
          • stephenw10S
            stephenw10 Netgate Administrator
            last edited by

            It does have a VGA header, J9, on the rear left of the board. It's a 2mm pitch connector though like most of these boxes not the more common 0.1".

            I've never tried it myself.

            Steve

            1 Reply Last reply Reply Quote 0
            • C
              cyablo
              last edited by

              Edit: See post below…

              1 Reply Last reply Reply Quote 0
              • C
                cyablo
                last edited by

                I took antother dump using a Raspberry Pi which had same sha256, so I'm pretty sure is got the dump right. Next I downgraded my BIOS to the mod'ed one… it works :)

                I enabled PowerD, added the additional lines to the loader.conf file, added timecounter variable... but SpeedStep does not seem to work:

                "CPU supports enhanced SpeedStep, but it's not recognized", also sysctl shows no freq_levels.

                My CPU does support it (Pentium E5800). Has anyone got it working? Ís there anything that needs to be changed in BIOS? Would be happy to lower the power consumption this way. Powermeter meassures around 32-33W idle at the moment.

                1 Reply Last reply Reply Quote 0
                • B
                  blaxx
                  last edited by

                  @blaxx:

                  Hi !

                  I don't know if this is a pfsense or XTM5 problem but I'll give it a try.

                  I have two XTM5 (510 and 525) with original BIOS and hardware except for hard drives that I have installed latest pfsense 2.3.4-p1 on. I have never used pfsense before so I installed it on these firewalls to see if it works. No changes are made on the config after first boot.

                  The problem is that after a couple of days both of the firewalls stops routing all traffic. Cant reach them from webgui and cant connect to internet at all anymore.
                  The only solution I've found is to pull the plug. After that it works for a couple of days again.

                  I read an old thread regarding a bug when using multicore cpu so I tried that fix by disabling all but one core but that didn't help.

                  Anyone have an idea regarding what might be the problem?

                  Kind regards

                  Stellan

                  So. I'm back now with the same problem again.
                  Since last time I've switched CPU, reinstalled pfsense from a new flashcard. This time it worked for nearly 14 days. 10 of these days with DSL connected to WAN and 1 pc direct connect to LAN0. The last four days the FW was only connected to DSL and nothin on LAN.

                  Today I connected a PC to LAN0 and no DHCP recieved. I can connect to console with consolecable trough Putty
                  I can ping both WAN and LAN interface and even google dns (8.8.8.8) via consolecable.
                  Can't reach webpages nor webinterface if I set static IP on PC.

                  Can anyone give me some tips to trace this problem?

                  Regards Stellan

                  Dmesg shows this:

                  [2.3.4-RELEASE][root@pfSense.JTT.local]/root: dmesg
Copyright (c) 1992-2016 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 10.3-RELEASE-p19 #1 76a12c4e6(RELENG_2_3_4): Fri Jul 14 15:02:35 CDT 2017
    root@ce23-amd64-builder:/builder/pfsense-234/tmp/obj/builder/pfsense-234/tmp/FreeBSD-src/sys/pfSense amd64
FreeBSD clang version 3.4.1 (tags/RELEASE_34/dot1-final 208032) 20140512
CPU: Intel(R) Core(TM)2 Quad CPU    Q8200  @ 2.33GHz (2327.54-MHz K8-class CPU)
  Origin="GenuineIntel"  Id=0x1067a  Family=0x6  Model=0x17  Stepping=10
  Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0xc08e39d <sse3,dtes64,mon,ds_cpl,est,tm2,ssse3,cx16,xtpr,pdcm,sse4.1,xsave,osxsave>AMD Features=0x20100800 <syscall,nx,lm>AMD Features2=0x1 <lahf>TSC: P-state invariant, performance statistics
real memory  = 2147483648 (2048 MB)
avail memory = 2003542016 (1910 MB)
Event timer "LAPIC" quality 400
ACPI APIC Table: <042610 APIC1157>
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s)
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
 cpu2 (AP): APIC ID:  2
 cpu3 (AP): APIC ID:  3
random: <software, yarrow="">initialized
ioapic0 <version 2.0="">irqs 0-23 on motherboard
wlan: mac acl policy registered
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff806209f0, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff80620aa0, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff80620b50, 0) error 1
iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi/.
iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_bss_fw, 0xffffffff80647cf0, 0) error 1
iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi/.
iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffffffff80647da0, 0) error 1
iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi/.
iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffffffff80647e50, 0) error 1
netmap: loaded module
kbd1 at kbdmux0
cryptosoft0: <software crypto="">on motherboard
padlock0: No ACE support.
acpi0: <042610 RSDT1157> on motherboard
acpi0: Power Button (fixed)
cpu0: <acpi cpu="">on acpi0
cpu1: <acpi cpu="">on acpi0
cpu2: <acpi cpu="">on acpi0
cpu3: <acpi cpu="">on acpi0
attimer0: <at timer="">port 0x40-0x43 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <at realtime="" clock="">port 0x70-0x71 irq 8 on acpi0
Event timer "RTC" frequency 32768 Hz quality 0
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0
pci0: <acpi pci="" bus="">on pcib0
vgapci0: <vga-compatible display="">port 0x6800-0x6807 mem 0xfe000000-0xfe3fffff,0xd0000000-0xdfffffff irq 16 at device 2.0 on pci0
agp0: <intel g41="" svga="" controller="">on vgapci0
agp0: aperture size is 256M, detected 32764k stolen memory
vgapci0: Boot video device
pcib1: <acpi pci-pci="" bridge="">irq 16 at device 28.0 on pci0
pci2: <acpi pci="" bus="">on pcib1
em0: <intel(r) 1000="" pro="" network="" connection="" 7.6.1-k="">port 0x9c00-0x9c1f mem 0xfe6e0000-0xfe6fffff,0xfe6dc000-0xfe6dffff irq 16 at device 0.0 on pci2
em0: Using MSIX interrupts with 3 vectors
em0: Ethernet address: 00:90:7f:9f:5f:6b
em0: netmap queues/slots: TX 1/1024, RX 1/1024
pcib2: <acpi pci-pci="" bridge="">irq 17 at device 28.1 on pci0
pci3: <acpi pci="" bus="">on pcib2
em1: <intel(r) 1000="" pro="" network="" connection="" 7.6.1-k="">port 0xac00-0xac1f mem 0xfe7e0000-0xfe7fffff,0xfe7dc000-0xfe7dffff irq 17 at device 0.0 on pci3
em1: Using MSIX interrupts with 3 vectors
em1: Ethernet address: 00:90:7f:9f:5f:6c
em1: netmap queues/slots: TX 1/1024, RX 1/1024
pcib3: <acpi pci-pci="" bridge="">irq 18 at device 28.2 on pci0
pci4: <acpi pci="" bus="">on pcib3
em2: <intel(r) 1000="" pro="" network="" connection="" 7.6.1-k="">port 0xbc00-0xbc1f mem 0xfe8e0000-0xfe8fffff,0xfe8dc000-0xfe8dffff irq 18 at device 0.0 on pci4
em2: Using MSIX interrupts with 3 vectors
em2: Ethernet address: 00:90:7f:9f:5f:6d
em2: netmap queues/slots: TX 1/1024, RX 1/1024
pcib4: <acpi pci-pci="" bridge="">irq 19 at device 28.3 on pci0
pci5: <acpi pci="" bus="">on pcib4
em3: <intel(r) 1000="" pro="" network="" connection="" 7.6.1-k="">port 0xcc00-0xcc1f mem 0xfe9e0000-0xfe9fffff,0xfe9dc000-0xfe9dffff irq 19 at device 0.0 on pci5
em3: Using MSIX interrupts with 3 vectors
em3: Ethernet address: 00:90:7f:9f:5f:6e
em3: netmap queues/slots: TX 1/1024, RX 1/1024
pcib5: <acpi pci-pci="" bridge="">irq 16 at device 28.4 on pci0
pci6: <acpi pci="" bus="">on pcib5
em4: <intel(r) 1000="" pro="" network="" connection="" 7.6.1-k="">port 0xdc00-0xdc1f mem 0xfeae0000-0xfeafffff,0xfeadc000-0xfeadffff irq 16 at device 0.0 on pci6
em4: Using MSIX interrupts with 3 vectors
em4: Ethernet address: 00:90:7f:9f:5f:6f
em4: netmap queues/slots: TX 1/1024, RX 1/1024
pcib6: <acpi pci-pci="" bridge="">irq 17 at device 28.5 on pci0
pci7: <acpi pci="" bus="">on pcib6
em5: <intel(r) 1000="" pro="" network="" connection="" 7.6.1-k="">port 0xec00-0xec1f mem 0xfebe0000-0xfebfffff,0xfebdc000-0xfebdffff irq 17 at device 0.0 on pci7
em5: Using MSIX interrupts with 3 vectors
em5: Ethernet address: 00:90:7f:9f:5f:70
em5: netmap queues/slots: TX 1/1024, RX 1/1024
uhci0: <intel 82801g="" (ich7)="" usb="" controller="" usb-a="">port 0x7080-0x709f irq 23 at device 29.0 on pci0
usbus0 on uhci0
uhci1: <intel 82801g="" (ich7)="" usb="" controller="" usb-b="">port 0x7000-0x701f irq 19 at device 29.1 on pci0
usbus1 on uhci1
uhci2: <intel 82801g="" (ich7)="" usb="" controller="" usb-c="">port 0x6c00-0x6c1f irq 18 at device 29.2 on pci0
usbus2 on uhci2
uhci3: <intel 82801g="" (ich7)="" usb="" controller="" usb-d="">port 0x6880-0x689f irq 16 at device 29.3 on pci0
usbus3 on uhci3
ehci0: <intel 82801gb="" r="" (ich7)="" usb="" 2.0="" controller="">mem 0xfe4ff800-0xfe4ffbff irq 23 at device 29.7 on pci0
usbus4: EHCI version 1.0
usbus4 on ehci0
pcib7: <acpi pci-pci="" bridge="">at device 30.0 on pci0
pci1: <acpi pci="" bus="">on pcib7
fxp0: <intel 10="" 100="" 82801gb="" (ich7)="" ethernet="">port 0x8c00-0x8c3f mem 0xfe5ff000-0xfe5fffff irq 20 at device 8.0 on pci1
miibus0: <mii bus="">on fxp0
inphy0: <i82562et 10="" 100="" media="" interface="">PHY 1 on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto, auto-flow
fxp0: Ethernet address: 00:90:7f:9f:5f:6a
isab0: <pci-isa bridge="">at device 31.0 on pci0
isa0: <isa bus="">on isab0
atapci0: <intel ich7="" udma100="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 31.1 on pci0
ata0: <ata channel="">at channel 0 on atapci0
atapci1: <intel ich7="" sata300="" controller="">port 0x7c00-0x7c07,0x7880-0x7883,0x7800-0x7807,0x7480-0x7483,0x7400-0x740f mem 0xfe4ffc00-0xfe4fffff irq 19 at device 31.2 on pci0
ata2: <ata channel="">at channel 0 on atapci1
ata3: <ata channel="">at channel 1 on atapci1
acpi_button0: <power button="">on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: console (115200,n,8,1)
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
ppc0: <parallel port="">port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <parallel port="" bus="">on ppc0
lpt0: <printer>on ppbus0
lpt0: Interrupt-driven port
ppi0: <parallel i="" o="">on ppbus0
sc0: <system console="">at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <generic isa="" vga="">at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <keyboard controller="" (i8042)="">at port 0x60,0x64 on isa0
atkbd0: <at keyboard="">irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
est0: <enhanced speedstep="" frequency="" control="">on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 616072506000725
device_attach: est0 attach returned 6
est1: <enhanced speedstep="" frequency="" control="">on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 616072506000725
device_attach: est1 attach returned 6
est2: <enhanced speedstep="" frequency="" control="">on cpu2
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 616072506000725
device_attach: est2 attach returned 6
est3: <enhanced speedstep="" frequency="" control="">on cpu3
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 616072506000725
device_attach: est3 attach returned 6
Timecounters tick every 1.000 msec
random: unblocking device.
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 12Mbps Full Speed USB v1.0
ugen0.1: <intel>at usbus0
uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
ugen1.1: <intel>at usbus1
uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
ugen2.1: <intel>at usbus2
uhub2: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus2
ugen3.1: <intel>at usbus3
uhub3: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus3
usbus4: 480Mbps High Speed USB v2.0
ugen4.1: <intel>at usbus4
uhub4: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus4
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
uhub4: 8 ports with 8 removable, self powered
ada0 at ata2 bus 0 scbus1 target 0 lun 0
ada0: <samsung hm250ji="" hs100-10="">ATA8-ACS SATA 1.x device
ada0: Serial Number S15YJD0PB08244
ada0: 150.000MB/s transfers (SATA 1.x, UDMA5, PIO 8192bytes)
ada0: 238475MB (488397168 512 byte sectors)
ada0: Previously was known as ad4
SMP: AP CPU #3 Launched!
SMP: AP CPU #1 Launched!
SMP: AP CPU #2 Launched!
Timecounter "TSC-low" frequency 1163771717 Hz quality 1000
Trying to mount root from ufs:/dev/ufsid/5996b7217d4aca1d [rw]...
coretemp0: <cpu on-die="" thermal="" sensors="">on cpu0
est0: <enhanced speedstep="" frequency="" control="">on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 616072506000725
device_attach: est0 attach returned 6
coretemp1: <cpu on-die="" thermal="" sensors="">on cpu1
est1: <enhanced speedstep="" frequency="" control="">on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 616072506000725
device_attach: est1 attach returned 6
coretemp2: <cpu on-die="" thermal="" sensors="">on cpu2
est2: <enhanced speedstep="" frequency="" control="">on cpu2
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 616072506000725
device_attach: est2 attach returned 6
coretemp3: <cpu on-die="" thermal="" sensors="">on cpu3
est3: <enhanced speedstep="" frequency="" control="">on cpu3
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 616072506000725
device_attach: est3 attach returned 6
em0: link state changed to UP
pflog0: promiscuous mode enabled
em1: link state changed to UP
fxp0: link state changed to DOWN
pflog0: promiscuous mode disabled
Waiting (max 60 seconds) for system process `vnlru' to stop...done
Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
Waiting (max 60 seconds) for system process `syncer' to stop...
Syncing disks, vnodes remaining...4 0 0 done
All buffers synced.
Copyright (c) 1992-2016 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 10.3-RELEASE-p19 #1 76a12c4e6(RELENG_2_3_4): Fri Jul 14 15:02:35 CDT 2017
    root@ce23-amd64-builder:/builder/pfsense-234/tmp/obj/builder/pfsense-234/tmp/FreeBSD-src/sys/pfSense amd64
FreeBSD clang version 3.4.1 (tags/RELEASE_34/dot1-final 208032) 20140512
CPU: Intel(R) Core(TM)2 Quad CPU    Q8200  @ 2.33GHz (2327.55-MHz K8-class CPU)
  Origin="GenuineIntel"  Id=0x1067a  Family=0x6  Model=0x17  Stepping=10
  Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0xc08e39d <sse3,dtes64,mon,ds_cpl,est,tm2,ssse3,cx16,xtpr,pdcm,sse4.1,xsave,osxsave>AMD Features=0x20100800 <syscall,nx,lm>AMD Features2=0x1 <lahf>TSC: P-state invariant, performance statistics
real memory  = 2147483648 (2048 MB)
avail memory = 2003542016 (1910 MB)
Event timer "LAPIC" quality 400
ACPI APIC Table: <042610 APIC1157>
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s)
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
 cpu2 (AP): APIC ID:  2
 cpu3 (AP): APIC ID:  3
random: <software, yarrow="">initialized
ioapic0 <version 2.0="">irqs 0-23 on motherboard
wlan: mac acl policy registered
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff806209f0, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff80620aa0, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff80620b50, 0) error 1
iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi/.
iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_bss_fw, 0xffffffff80647cf0, 0) error 1
iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi/.
iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffffffff80647da0, 0) error 1
iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi/.
iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffffffff80647e50, 0) error 1
netmap: loaded module
kbd1 at kbdmux0
cryptosoft0: <software crypto="">on motherboard
padlock0: No ACE support.
acpi0: <042610 RSDT1157> on motherboard
acpi0: Power Button (fixed)
cpu0: <acpi cpu="">on acpi0
cpu1: <acpi cpu="">on acpi0
cpu2: <acpi cpu="">on acpi0
cpu3: <acpi cpu="">on acpi0
attimer0: <at timer="">port 0x40-0x43 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <at realtime="" clock="">port 0x70-0x71 irq 8 on acpi0
Event timer "RTC" frequency 32768 Hz quality 0
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0
pci0: <acpi pci="" bus="">on pcib0
vgapci0: <vga-compatible display="">port 0x6800-0x6807 mem 0xfe000000-0xfe3fffff,0xd0000000-0xdfffffff irq 16 at device 2.0 on pci0
agp0: <intel g41="" svga="" controller="">on vgapci0
agp0: aperture size is 256M, detected 32764k stolen memory
vgapci0: Boot video device
pcib1: <acpi pci-pci="" bridge="">irq 16 at device 28.0 on pci0
pci2: <acpi pci="" bus="">on pcib1
em0: <intel(r) 1000="" pro="" network="" connection="" 7.6.1-k="">port 0x9c00-0x9c1f mem 0xfe6e0000-0xfe6fffff,0xfe6dc000-0xfe6dffff irq 16 at device 0.0 on pci2
em0: Using MSIX interrupts with 3 vectors
em0: Ethernet address: 00:90:7f:9f:5f:6b
em0: netmap queues/slots: TX 1/1024, RX 1/1024
pcib2: <acpi pci-pci="" bridge="">irq 17 at device 28.1 on pci0
pci3: <acpi pci="" bus="">on pcib2
em1: <intel(r) 1000="" pro="" network="" connection="" 7.6.1-k="">port 0xac00-0xac1f mem 0xfe7e0000-0xfe7fffff,0xfe7dc000-0xfe7dffff irq 17 at device 0.0 on pci3
em1: Using MSIX interrupts with 3 vectors
em1: Ethernet address: 00:90:7f:9f:5f:6c
em1: netmap queues/slots: TX 1/1024, RX 1/1024
pcib3: <acpi pci-pci="" bridge="">irq 18 at device 28.2 on pci0
pci4: <acpi pci="" bus="">on pcib3
em2: <intel(r) 1000="" pro="" network="" connection="" 7.6.1-k="">port 0xbc00-0xbc1f mem 0xfe8e0000-0xfe8fffff,0xfe8dc000-0xfe8dffff irq 18 at device 0.0 on pci4
em2: Using MSIX interrupts with 3 vectors
em2: Ethernet address: 00:90:7f:9f:5f:6d
em2: netmap queues/slots: TX 1/1024, RX 1/1024
pcib4: <acpi pci-pci="" bridge="">irq 19 at device 28.3 on pci0
pci5: <acpi pci="" bus="">on pcib4
em3: <intel(r) 1000="" pro="" network="" connection="" 7.6.1-k="">port 0xcc00-0xcc1f mem 0xfe9e0000-0xfe9fffff,0xfe9dc000-0xfe9dffff irq 19 at device 0.0 on pci5
em3: Using MSIX interrupts with 3 vectors
em3: Ethernet address: 00:90:7f:9f:5f:6e
em3: netmap queues/slots: TX 1/1024, RX 1/1024
pcib5: <acpi pci-pci="" bridge="">irq 16 at device 28.4 on pci0
pci6: <acpi pci="" bus="">on pcib5
em4: <intel(r) 1000="" pro="" network="" connection="" 7.6.1-k="">port 0xdc00-0xdc1f mem 0xfeae0000-0xfeafffff,0xfeadc000-0xfeadffff irq 16 at device 0.0 on pci6
em4: Using MSIX interrupts with 3 vectors
em4: Ethernet address: 00:90:7f:9f:5f:6f
em4: netmap queues/slots: TX 1/1024, RX 1/1024
pcib6: <acpi pci-pci="" bridge="">irq 17 at device 28.5 on pci0
pci7: <acpi pci="" bus="">on pcib6
em5: <intel(r) 1000="" pro="" network="" connection="" 7.6.1-k="">port 0xec00-0xec1f mem 0xfebe0000-0xfebfffff,0xfebdc000-0xfebdffff irq 17 at device 0.0 on pci7
em5: Using MSIX interrupts with 3 vectors
em5: Ethernet address: 00:90:7f:9f:5f:70
em5: netmap queues/slots: TX 1/1024, RX 1/1024
uhci0: <intel 82801g="" (ich7)="" usb="" controller="" usb-a="">port 0x7080-0x709f irq 23 at device 29.0 on pci0
usbus0 on uhci0
uhci1: <intel 82801g="" (ich7)="" usb="" controller="" usb-b="">port 0x7000-0x701f irq 19 at device 29.1 on pci0
usbus1 on uhci1
uhci2: <intel 82801g="" (ich7)="" usb="" controller="" usb-c="">port 0x6c00-0x6c1f irq 18 at device 29.2 on pci0
usbus2 on uhci2
uhci3: <intel 82801g="" (ich7)="" usb="" controller="" usb-d="">port 0x6880-0x689f irq 16 at device 29.3 on pci0
usbus3 on uhci3
ehci0: <intel 82801gb="" r="" (ich7)="" usb="" 2.0="" controller="">mem 0xfe4ff800-0xfe4ffbff irq 23 at device 29.7 on pci0
usbus4: EHCI version 1.0
usbus4 on ehci0
pcib7: <acpi pci-pci="" bridge="">at device 30.0 on pci0
pci1: <acpi pci="" bus="">on pcib7
fxp0: <intel 10="" 100="" 82801gb="" (ich7)="" ethernet="">port 0x8c00-0x8c3f mem 0xfe5ff000-0xfe5fffff irq 20 at device 8.0 on pci1
miibus0: <mii bus="">on fxp0
inphy0: <i82562et 10="" 100="" media="" interface="">PHY 1 on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto, auto-flow
fxp0: Ethernet address: 00:90:7f:9f:5f:6a
isab0: <pci-isa bridge="">at device 31.0 on pci0
isa0: <isa bus="">on isab0
atapci0: <intel ich7="" udma100="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 31.1 on pci0
ata0: <ata channel="">at channel 0 on atapci0
atapci1: <intel ich7="" sata300="" controller="">port 0x7c00-0x7c07,0x7880-0x7883,0x7800-0x7807,0x7480-0x7483,0x7400-0x740f mem 0xfe4ffc00-0xfe4fffff irq 19 at device 31.2 on pci0
ata2: <ata channel="">at channel 0 on atapci1
ata3: <ata channel="">at channel 1 on atapci1
acpi_button0: <power button="">on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: console (115200,n,8,1)
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
ppc0: <parallel port="">port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <parallel port="" bus="">on ppc0
lpt0: <printer>on ppbus0
lpt0: Interrupt-driven port
ppi0: <parallel i="" o="">on ppbus0
sc0: <system console="">at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <generic isa="" vga="">at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <keyboard controller="" (i8042)="">at port 0x60,0x64 on isa0
atkbd0: <at keyboard="">irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
est0: <enhanced speedstep="" frequency="" control="">on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 616072506000725
device_attach: est0 attach returned 6
est1: <enhanced speedstep="" frequency="" control="">on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 616072506000725
device_attach: est1 attach returned 6
est2: <enhanced speedstep="" frequency="" control="">on cpu2
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 616072506000725
device_attach: est2 attach returned 6
est3: <enhanced speedstep="" frequency="" control="">on cpu3
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 616072506000725
device_attach: est3 attach returned 6
Timecounters tick every 1.000 msec
random: unblocking device.
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 12Mbps Full Speed USB v1.0
ugen0.1: <intel>at usbus0
uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
ugen1.1: <intel>at usbus1
uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
ugen2.1: <intel>at usbus2
uhub2: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus2
ugen3.1: <intel>at usbus3
uhub3: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus3
usbus4: 480Mbps High Speed USB v2.0
ugen4.1: <intel>at usbus4
uhub4: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus4
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
uhub4: 8 ports with 8 removable, self powered
ada0 at ata2 bus 0 scbus1 target 0 lun 0
ada0: <samsung hm250ji="" hs100-10="">ATA8-ACS SATA 1.x device
ada0: Serial Number S15YJD0PB08244
ada0: 150.000MB/s transfers (SATA 1.x, UDMA5, PIO 8192bytes)
ada0: 238475MB (488397168 512 byte sectors)
ada0: Previously was known as ad4
SMP: AP CPU #2 Launched!
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
Timecounter "TSC-low" frequency 1163774381 Hz quality 1000
Trying to mount root from ufs:/dev/ufsid/5996b7217d4aca1d [rw]...
coretemp0: <cpu on-die="" thermal="" sensors="">on cpu0
est0: <enhanced speedstep="" frequency="" control="">on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 616072506000725
device_attach: est0 attach returned 6
coretemp1: <cpu on-die="" thermal="" sensors="">on cpu1
est1: <enhanced speedstep="" frequency="" control="">on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 616072506000725
device_attach: est1 attach returned 6
coretemp2: <cpu on-die="" thermal="" sensors="">on cpu2
est2: <enhanced speedstep="" frequency="" control="">on cpu2
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 616072506000725
device_attach: est2 attach returned 6
coretemp3: <cpu on-die="" thermal="" sensors="">on cpu3
est3: <enhanced speedstep="" frequency="" control="">on cpu3
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 616072506000725
device_attach: est3 attach returned 6
em0: link state changed to UP
pflog0: promiscuous mode enabled
em1: link state changed to UP
fxp0: link state changed to DOWN
em0: Watchdog timeout Queue[0]-- resetting
Interface is RUNNING and ACTIVE
em0: TX Queue 0 ------
em0: hw tdh = 990, hw tdt = 950
em0: Tx Queue Status = -2147483648
em0: TX descriptors avail = 40
em0: Tx Descriptors avail failure = 31
em0: RX Queue 0 ------
em0: hw rdh = 767, hw rdt = 766
em0: RX discarded packets = 0
em0: RX Next to Check = 767
em0: RX Next to Refresh = 766
em0: link state changed to DOWN
em0: link state changed to UP
em1: Watchdog timeout Queue[0]-- resetting
Interface is RUNNING and ACTIVE
em1: TX Queue 0 ------
em1: hw tdh = 909, hw tdt = 869
em1: Tx Queue Status = -2147483648
em1: TX descriptors avail = 40
em1: Tx Descriptors avail failure = 2
em1: RX Queue 0 ------
em1: hw rdh = 800, hw rdt = 799
em1: RX discarded packets = 0
em1: RX Next to Check = 800
em1: RX Next to Refresh = 799
em1: link state changed to DOWN
em1: link state changed to UP
[2.3.4-RELEASE][root@pfSense.JTT.local]/root:</enhanced></cpu></enhanced></cpu></enhanced></cpu></enhanced></cpu></samsung></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></enhanced></enhanced></enhanced></enhanced></at></keyboard></generic></system></parallel></printer></parallel></parallel></power></ata></ata></intel></ata></intel></isa></pci-isa></i82562et></mii></intel></acpi></acpi></intel></intel></intel></intel></intel></intel(r)></acpi></acpi></intel(r)></acpi></acpi></intel(r)></acpi></acpi></intel(r)></acpi></acpi></intel(r)></acpi></acpi></intel(r)></acpi></acpi></intel></vga-compatible></acpi></acpi></at></at></acpi></acpi></acpi></acpi></software></version></software,></lahf></syscall,nx,lm></sse3,dtes64,mon,ds_cpl,est,tm2,ssse3,cx16,xtpr,pdcm,sse4.1,xsave,osxsave></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe></enhanced></cpu></enhanced></cpu></enhanced></cpu></enhanced></cpu></samsung></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></enhanced></enhanced></enhanced></enhanced></at></keyboard></generic></system></parallel></printer></parallel></parallel></power></ata></ata></intel></ata></intel></isa></pci-isa></i82562et></mii></intel></acpi></acpi></intel></intel></intel></intel></intel></intel(r)></acpi></acpi></intel(r)></acpi></acpi></intel(r)></acpi></acpi></intel(r)></acpi></acpi></intel(r)></acpi></acpi></intel(r)></acpi></acpi></intel></vga-compatible></acpi></acpi></at></at></acpi></acpi></acpi></acpi></software></version></software,></lahf></syscall,nx,lm></sse3,dtes64,mon,ds_cpl,est,tm2,ssse3,cx16,xtpr,pdcm,sse4.1,xsave,osxsave></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>
                  1 Reply Last reply Reply Quote 0
                  • B
                    Billyboy
                    last edited by

                    @stephenw10:

                    Hmm, and you're actually pulling the cable from the port on the xtm5?

                    What does ifconfig show for that port during that time?

                    Steve

                    Yes, I am pulling the cable directly at the box.

                    That's the ifconfig output after pulling the cable:

                    em4: flags=8943 <up,broadcast,running,promisc,simplex,multicast>metric 0 mtu 1500
                      options=42098 <vlan_mtu,vlan_hwtagging,vlan_hwcsum,wol_magic,vlan_hwtso>ether 00:90:7f:84:61:dc
                      hwaddr 00:90:7f:84:61:dc
                      inet6 fe80::290:7fff:fe84:61dc%em4 prefixlen 64 scopeid 0x5
                      inet 192.168.245.101 netmask 0xffffff00 broadcast 192.168.245.255
                      inet 192.168.245.100 netmask 0xffffff00 broadcast 192.168.245.255 vhid 5
                      nd6 options=21 <performnud,auto_linklocal>media: Ethernet autoselect (1000baseT <full-duplex>)
                      status: active
                      carp: MASTER vhid 5 advbase 1 advskew 0</full-duplex></performnud,auto_linklocal></vlan_mtu,vlan_hwtagging,vlan_hwcsum,wol_magic,vlan_hwtso></up,broadcast,running,promisc,simplex,multicast>

                    1 Reply Last reply Reply Quote 0
                    • stephenw10S
                      stephenw10 Netgate Administrator
                      last edited by

                      @blaxx

                      This looks bad:

                      em0: Watchdog timeout Queue[0]-- resetting

                      Something is giving those interfaces a hard time.

                      @Billyboy

                      Hmm, I've never seen that before on any interface. It's hard to imagine what could allow the driver to report that as UP.

                      Steve

                      1 Reply Last reply Reply Quote 0
                      • B
                        blaxx
                        last edited by

                        @stephenw10:

                        @blaxx

                        This looks bad:

                        em0: Watchdog timeout Queue[0]-- resetting

                        Something is giving those interfaces a hard time.

                        Steve

                        Expecting HW? Is there anything I can do trace the fault?
                        I found another user with the same problem as me but that thread doesn't seem to be solved.

                        https://forum.pfsense.org/index.php?topic=116956.0

                        Stellan

                        1 Reply Last reply Reply Quote 0
                        • stephenw10S
                          stephenw10 Netgate Administrator
                          last edited by

                          Do you have 'Hardware TCP Segmentation Offloading' disabled in System > Advanced > Networking?

                          It should be disabled by default.

                          Steve

                          1 Reply Last reply Reply Quote 0
                          • B
                            blaxx
                            last edited by

                            @stephenw10:

                            Do you have 'Hardware TCP Segmentation Offloading' disabled in System > Advanced > Networking?

                            It should be disabled by default.

                            Steve

                            Yes it is disabled. The config is default except for installation of LCDproc.

                            Stellan

                            1 Reply Last reply Reply Quote 0
                            • stephenw10S
                              stephenw10 Netgate Administrator
                              last edited by

                              Hmm, you might try some of the other tuning options here:
                              https://doc.pfsense.org/index.php/Tuning_and_Troubleshooting_Network_Cards#Intel_igb.284.29_and_em.284.29_Cards

                              You could also try:

                              hw.em.num_queues=1

                              or

                              hw.em.msix=0

                              Neither of which should be necessary really.

                              Steve

                              1 Reply Last reply Reply Quote 0
                              • P
                                pd1dmr
                                last edited by

                                Found one on Ebay

                                and it is on its way to me  :)

                                can somebody confirm that installing from cf card to hdd works

                                so it will boot from hdd

                                got PFsense running on PC know

                                and Bios Flash from 2.3.4 pfsense install possible to custom bios made by Steve

                                Many thnx
                                Rex

                                1 Reply Last reply Reply Quote 0
                                • stephenw10S
                                  stephenw10 Netgate Administrator
                                  last edited by

                                  Yeah that would probably work. I've never done that on that hardware but I've done similar things on other devices.

                                  Write the memstick-serial install image to a CF card and it should boot from that and allow you to install to HD. I'm not sure if it will try to boot CF or HD first with the default BIOS settings.

                                  You can write the BIOS using flashrom in pfSense.

                                  Steve

                                  1 Reply Last reply Reply Quote 0
                                  • B
                                    Billyboy
                                    last edited by

                                    Hi all,

                                    one of my two XTM boxes surprisingly doesn´t start today.  When I power it up (with the power cord), the fans blow at 100%, some (not all) LEDs on the ports are flickering or blinking, nothing in the display, no beep, no boot, power button does not work. Serial connection does not work/show anything with 9600 nor 115200 8N1. (On the the other box it works, so no cable or software issue).
                                    Entering the Safe Mode does not work (as described by Watchguard https://www.watchguard.com/help/docs/wsm/xtm_11/en-us/content/en-us/backup_upgrade_recovery/recovery_procedures_c.html )

                                    Meanwhile I opened the box and disconnected the SATA SSD, still same behavior. All the five LEDs on the back of the mainboard are glowing, when power is connected.

                                    Any Idea? Does it need a reset? How?

                                    Any help appreciated, thx in advance!

                                    1 Reply Last reply Reply Quote 0
                                    • stephenw10S
                                      stephenw10 Netgate Administrator
                                      last edited by

                                      Sounds like a hardware issue.

                                      I'd try disconnecting everything you can, which isn;t much in the XTM5. Rmove the crypto card though if you haven't already.

                                      Reseat the memory and CPU. Remove any additional DIMMs you might be using. Reset the CMOS.

                                      Steve

                                      1 Reply Last reply Reply Quote 0
                                      • ?
                                        A Former User
                                        last edited by

                                        This post is deleted!
                                        1 Reply Last reply Reply Quote 0
                                        • B
                                          Billyboy
                                          last edited by

                                          Hi Steve, thank you, how can I reset the CMOS? Is there a jumper or should i remove the small battery?

                                          @stephenw10:

                                          Sounds like a hardware issue.

                                          I'd try disconnecting everything you can, which isn;t much in the XTM5. Rmove the crypto card though if you haven't already.

                                          Reseat the memory and CPU. Remove any additional DIMMs you might be using. Reset the CMOS.

                                          Steve

                                          1 Reply Last reply Reply Quote 0
                                          • stephenw10S
                                            stephenw10 Netgate Administrator
                                            last edited by

                                            Removing the battery for 10mins is a good way. There is a jumper but I forget exactly where, usually near the battery though.

                                            Steve

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.