PC Engines APU2 with 4 ethernet cards
-
UPDATE: I've just received the Mini-PCIe NIC I've ordered. It's a cheap one from ebay with a realtek RTL8111E chipset. I've inserted it into the slot mPCIe 1, and the system detects it just fine. The three native interfaces on APU2 appear as igb0, igb1 and igb2 while the realtek is marked as "re0". I'll see, if I can get it running. Currently I'm having trouble accessing the interface from my PC, but it's the same story with another existing NIC on APU2, so I'm pretty sure it's a firewall issue.
EDIT: Yay, fixed it. The mPCIe wired interface now works properly. I now have 4 physical NIC's on APU2C4!
-
I'm in the same boat, but would prefer to go the VLAN route
@Ire: Can you recommend $50 or less 5 to 8 port managed switch?
@repne: What enclouse did you use for this?
-
UPDATE: I've just received the Mini-PCIe NIC I've ordered. It's a cheap one from ebay with a realtek RTL8111E chipset. I've inserted it into the slot mPCIe 1, and the system detects it just fine. The three native interfaces on APU2 appear as igb0, igb1 and igb2 while the realtek is marked as "re0". I'll see, if I can get it running. Currently I'm having trouble accessing the interface from my PC, but it's the same story with another existing NIC on APU2, so I'm pretty sure it's a firewall issue.
EDIT: Yay, fixed it. The mPCIe wired interface now works properly. I now have 4 physical NIC's on APU2C4!
I'm curious: how did you solve the problem with the case? The apu2 comes with a 3-ethernet case. Did you drill/cut out an additional hole yourself? Or did you buy a different case?
-
I would just go with a supermicro solution. Great celeron and atom based solutions!
-
I'm in the same boat, but would prefer to go the VLAN route
@Ire: Can you recommend $50 or less 5 to 8 port managed switch?
@repne: What enclouse did you use for this?
1. Why?
2. Netgear GS105E, GS108E & GS108Tv2 (~$25, ~$35, ~$69)
3. Here is a nice one that comes with additional RJ45 breakout holes.
PC Engines APU1/APU2 case with HDD, WiFi + 2 LAN Ports - Black 35 Euro plus tax.Here is a reported miniPCIe dual NIC that is working well with pfSense.APU2C4 with 5 LAN Ports
-
Hello everyone.
I got a new APU2C4 and have installed pfSense and running it with no issues.
I know that it might be obvious but I want to utilise all 3 NICs of the board.
In the meantime I only use igb0 as WAN and igb1 as LAN.
I want to use the third one (igb2) as LAN too but not with a different gateway and subnet mask.
In short, I want igb2 to be in the same network with LAN (igb1).
I tried to bridge these 2 interfaces but still can't get the igb2 to provide internet access to the connected devices.Can anyone please let me know how am I going to make the 2 LAN NICs to act as one?
Any help will be much appreciated
-
I got a new APU2C4 and have installed pfSense and running it with no issues.
Which version you have installed?
I know that it might be obvious but I want to utilise all 3 NICs of the board.
In the meantime I only use igb0 as WAN and igb1 as LAN.
I want to use the third one (igb2) as LAN too but not with a different gateway and subnet mask.Ok you can do that with ease.
In short, I want igb2 to be in the same network with LAN (igb1).
I tried to bridge these 2 interfaces but still can't get the igb2 to provide internet access to the connected devices.Why, bridging is often a dead end road.
Can anyone please let me know how am I going to make the 2 LAN NICs to act as one?
Configure a LAG (LACP) if you switch is supporting it right now. If not a small Netgear GS108Tv2 will
do the job for ~$70 newish or for ~$40 refurbished on ebay. -
Thanks for your time and kind reply.
Eventually I got to set the 2 NICs to act as ONE LAN interface following the guide below.
I'm posting it here for future reference as well as for anyone who wants to achieve the same thing.
I couldn't imagine a simple requirement like this would need such a complex configuration. However it works now.https://mtu.net/~engstrom/configure-pfsense-bridge-over-multiple-nics-as-lan/
-
By the way, the mini PCIe cards do suck quite often, mostly because or poor space constrained design. Most of the cards I tried are RT 8111 based, and die within a year, even fir active airflow. In half the cases it was the on-board DC-DC, in the other cases it was the network chip itself. Bit of a mixed bag so far…
Going with the VLAN option would would out best.
-
Most of the cards I tried are RT 8111 based,
Must not be. NISK300LAN Kit
NISK300LAN Kit with universal I/O bracket is specifically designed with NISE300 and NISE 4000/NIFE 4000 models for network connectivity expansions. It provides dual Intel Gigabit Ethernet ports with latest I210IT controllers, which gives great network connectivity and less power consumption compared to the previous generation Intel 82574L controllers. The dual LAN ports on NISK300LAN Kit supports WoL, PXE and teaming functions for managing network activities. -
@gtj:
Eventually I got to set the 2 NICs to act as ONE LAN interface …
You know that bridging two interfaces in software is far from being a switch?
Each 10$ 5-port switch is way better siuted for such a task than sending each packet through the software stack down to the kernel and back up again. A switch usually does that in hardware or at least in a dedicated ASIC or FPGA highly specialized for such a task.
And do not expect wirespeed from your bridge.Just saying.
-
The guide you were following misses one point and that is correct filtering.
Usually you filter on each interface individually.
There's an advanced option at System Tunables where you can set pfSense to filter on the bridge instead.
net.link.bridge.pfil_member Set to 0 to disable filtering on the incoming and outgoing member interfaces. | default (1)
net.link.bridge.pfil_bridge Set to 1 to enable filtering on the bridge interface | default (0)Better than using an interface group and way easier to understand when doing changes in 7 months or so.