Make host go out specific WAN interface
-
hi all,
i have a pfsense firewall and i have two (x2) WAN addresses and atm all my traffic going out is coming from my WAN1
if i want to make a single host go out WAN2
is this possible
many thanks,
rob
-
I will try to answer this. Experts : Correct me if i am wrong
You can setup a rule on LAN interface
Within the rule, Under Source, select "Single Host or alias", Define the ip address of the machine which should go out through WAN2
Next under Extra Options, click on "Display Advanced", Scroll down to "Gateway" and choose the one for WAN2Just ensure the rules are in correct order else this source will hit the default LAN rule first and follow the regular path
-
so i dont need to do it under "Firewall > NAT > Outbound" just make a simple rule under "Firewall > Rules"
i just want this host to use WAN2 for traffic in/out
and all other traffic to use WAN1 in/out
-
As long as the source address is already covered in the normal outbound NAT rules on that WAN interface you are good.
Outbound NAT only determines what NAT takes place. It has no bearing on what gets routed where.
Policy route your source address with the desired gateway set (or no gateway if the default route is what you need) above any more general rules that would also match the traffic. The rules would be on "LAN"
-
This is exactly what im after
https://forum.pfsense.org/index.php?topic=106305.0
I still really dont get what outband nat is as i thought it was exactly for this to make a host or network go out a different gateway or wan interface
-
Outbound NAT has no effect on routing.
It controls what NAT takes place when a new connection goes out a particular interface.
Most simple networks can use Automatic NAT.
Common uses for custom rules are for things like SIP PBXes that need static ports (if the source port from the PBX is 5060, if needs to be sourced from 5060 out the WAN interface (after NAT) too).
It can be used if you have multiple WAN addresses. (If the connection is to destination TCP/25, set the source address to X.X.X.X, else use X.X.X.Y)
If you have internal networks with public addresses that are routed to you, you might use a Do Not NAT rule for those source addresses so no NAT happens at all.
In any case, the routing table or policy routing has already chosen that WAN as the interface to use for the connection. The outbound NAT rules have zero influence over that decision.
-
ok so below point 9 is what your saying "policy based route" so make that host use the WAN 2 gateway instead of the default one ie WAN1
but why has he done point 8?
thanks,
rob
08-configure-outbound-nat
There's a new(ish) hybrid mode for outbound NAT which makes this pretty easy. Add the two rules shown in the screenshots and then set the Mode to Hybrid Outbound NAT. I use the entire LAN subnet as the source address for these entries, but it could also be limited to the network block chosen for vpnclients (192.168.1.128/27). I use the entire LAN subnet so I don't have to worry about updating outbound NAT rules if I want to change the vpnclients alias.
09-create-lan-firewall-rules
Add a rule to block vpnclients from making DNS queries to the LAN IP. This prevents vpnclients from using the DNS Resolver and prevents DNS leaks if you forget to override DNS settings when adding static DHCP mappings for vpnclients.
Add a rule that creates a policy based route for vpnclients. Traffic that matches the rule will be sent via the VPN (ex:TORGUARD) gateway. Traffic that doesn't match will fall through to the default LAN rule.
-
I have no idea. Because he doesn't understand either?
The Automatic NAT rules show you what source addresses the firewall has determined should be NATted. If your source network is included, you need not do anything. If it is not you can switch to hybrid (or manual) and add it.
-
the last step i need help with is point 10 (below) the "no_wan_egress" i imagine this is an alias to some networks?
10-create-floating-firewall-rules
Create a floating rule that watches for and rejects outbound WAN traffic that's marked NO_WAN_EGRESS. This prevents vpnclients from connecting to the internet via the WAN when the VPN interface goes down.
-
No. It's a mark.
See this:
https://www.infotechwerx.com/blog/Prevent-Any-Traffic-VPN-Hosts-Egressing-WAN
-
thanks Derelict
-
mmm… somethings not right
i attach a picture of my rules and floating rules -
https://s18.postimg.org/fxir0ko49/rules.png
basically my "internal network" is 10.100.1.0/24
my "VPNclient" is 10.100.1.10 so it falls within the internal network subnet, i dont know if that matters
my DHCP server is from the range of 10.100.1.50-10.100.1.200 so my vpnclient alias IP is not in the scope
as soon as i change my pc NIC to 10.100.1.10 i loose internet
any help would be great, i persume im doing something really stupid!
cheers,
rob
-
ok i have added a new network on my switch "172.17.2.0/24" and i have made my pc "172.17.2.1"
i have added a new static route on pfsense so the to can talk to eachother ie pfsense and my switch
i have network access fine ie i can talk to other subnets but i still get no internet activity
can anyone help please
thanks
rob
-
Static route? Why a static route?
You are going to have to produce a diagram. See the one in my sig for the type of info necessary.
-
i attach a better betwork diagram of my static routes to my switch and pfsense
https://s18.postimg.org/v2d0so15l/my_network.png
yeah i have static routes set up to route traffic from my default network on my pfsense to all my other networks on my switch
i attach a picture so you have more of a understanding on my network
https://s18.postimg.org/nz8tnpn4p/route.png
my pfsense ip is "10.100.1.254" and switch on the same network is "10.100.1.253" and it carrys static routes down it so my devices connected to my switch on different subnets can see the network and the internet
on my pc i have made my default gateway the VPN network switch IP "172.17.2.253"
-
Whatever that is it is not a network diagram.
-
Yeah I ain't downloading some zip file from a forum user.
-
here you go
https://s18.postimg.org/tvlldbuvd/network.png
-
Is 172.17.2.0/24 covered by automatic outbound NAT?
Do the firewall rules on the 10.100.1.254 interface pass traffic from all of the static route source addresses?
I would not design it that way. I would use another router interface for the transit network to the switch and one for management. Management should probably not be a layer 3 interface on the switch.
-
you mean this under firewall > NAT > outbound
https://s18.postimg.org/pmgvbe4jd/nat_out.png
sorry i dont reallt understand second question?
i have an alia called "internal network" with manage and VM networks that are allowed out to the intnernet but the vpn isnt
