SG-1000 performance
-
pfsense is receiving a public address. I have now tried one of these switches between pfsense and the modem - https://www.tp-link.com/us/products/details/cat-42_TL-SG108.html, no change in speeds, 10Mbps down and 5Mbps up
-
pppoe or just ethernet?
have you tried other cables? how about error readings on the interface? half duplex / full duplex ?
need more intel to go on
-
ethernet connection on WAN and LAN. Have experimented with different cables and different duplex/speed settings on the WAN interface. The speeds do seem to be peak a little faster the first speed test following a reboot, but by the second speed test the peaks are closer to the average.
Havent been able to find any errors associated with the interfaces, though not totally certain I am looking in the right places, will continue to dig around.
One thing that did seem curious is that while I perform a speed test from a client connected to the LAN, I can see the following process is always the top CPU consumer, however never peaks above 5% CPU
PID USERNAME PRI NICE SIZE RES STATE TIME WCPU COMMAND
10 root 155 ki31 0K 8K RUN 13:54 88.33% [idle]
11 root -92 - 0K 176K WAIT 0:08 1.86% [intr{aintc0,41: cpswss0}]Still researching, posting this in case it makes others think of something.
Thanks for the help here, any other tips greatly appreciated.
-
Mmm, if it's on;y passing 10Mbps, 86% idle seems about right. That process looks normal.
Does it show a link at 1Gbps on both NICs? What exactly is it connected to on the WAN? What does your ISP provide there?
Steve
-
I think the attachment shows that both interfaces are negotiating 1Gbps? Is there a better way to check for both NICs showing a link at 1Gbps?
I have tried 3 different connections on the WAN, all showing the same throughput. directly into a Netgear CM600 - https://www.netgear.com/home/products/networking/cable-modems-routers/CM600.aspx. Then behind that CM600 both a TP Link TL-SG108 - https://www.tp-link.com/us/products/details/cat-42_TL-SG108.html, and an ASUS RT-88U - https://www.asus.com/us/Networking/RT-AC88U/ connecting into the SG-1000.
My ISP is comcast and the package is advertised as 150Mb/s download speed and 5Mb/s upload speed. with the CM600 as the modem and the ASUS router I have seen speeds slightly greater than these advertised speeds, even over wireless.
-
Have you ever seen a faster speed than that? Is this a new deployment? In a previous location perhaps? It looks like that device is ~6m old.
Steve
-
Quick glance suggests Interface(s) somehow negotiated down to 10BT. Interfaces statistics under Dashboard should tell you exactly what's what, but I suspect undisclosed configurations on your part doing it. Did it EVER worked properly when you newly installed pfsense BEFORE any configuration changes?
-
I regularly see faster speeds through my Asus router on the same cables. I had this device on a different connection prior to its current location and saw speeds better than they are now. When I moved the device I set it back to factory defaults and upgraded to the 2.4 release. I went ahead and flashed back to the factory image, but no change in speeds. The interface statistics in the dashboard show both interfaces at 1000T.
At this point I am thinking there must be some optimization within pfsense configuration for this specific device…any ideas?
-
i would disable ip6 on the sg 1k and see if your speeds change
-
I have gone into Interfaces and set the IPv6 Configuration Type to none for both interfaces. I have also disabled the DHCPv6 Server & RA service. No change in speeds with any of these configuration changes. Are there other settings relevant to disabling IPv6?
-
i've always followed this: https://airvpn.org/topic/17444-how-to-set-up-pfsense-23-for-airvpn/#entry40137
-
Just to confirm these are the speeds you're seeing direct right? Not via VPN?
Steve
-
Have gone through those steps to disable IPv6, no change in speeds.
And correct, this is just a direct connection to my ISP, no VPN connections.
