Static IP on WAN results in no connectivity
-
@johnpoz said in Static IP on WAN results in no connectivity:
@dominicm said in Static IP on WAN results in no connectivity:
I also tried with gateway set to none, why does it still work?
Where did you set gateway to none?
Wan interface -> Static IPv4 Configuration -> IPv4 Upstream gateway
I don't see any other gateway option.
-
post up a picture of
System / Routing / Gatewaysit not going to work if you do not have a gateway set on your wan..
-
It's literally only one entry I added (this is a clean pfsense install):
Sky (default) WAN 192.168.2.1 192.168.2.1Both "Sky" and "None" seems to work in WAN settings.
-
that is your default route - so yeah its going to work with that.. its your "default"
If you remove that then no its not going to work..
-
@dominicm said in Static IP on WAN results in no connectivity:
Why is it default if it's the wrong setting?
A /32 is used to denote a specific address. On a network, you need at least 2 devices to be useful. That means a mask no longer than a /31, as might be used on point to point links. You need at least as many addresses as possible devices, which is why we often see /24 on local networks. That provides room for 256 addresses, of which 254 are usable.
-
@johnpoz said in Static IP on WAN results in no connectivity:
that is your default route - so yeah its going to work with that.. its your "default"
If you remove that then no its not going to work..
I did think that default might do that so I tried disabling it before I posted and it's still working fine. It looks like it didn't apply until I rebooted after an update. I only got connectivity back after I enabled the gateway and set it in WAN page.
-
From what you said it seems like /32 would never be usable in WAN settings so why would it be the default I do not understand. I would expect a default to be the most common config or something similar.
-
Its the end of the the dropdown list nothing more.. ANYONE setting a static IP should KNOW what the mask means - or they shouldn't be freaking setting it static in the first place. Or they would be following directions given to them with what mask to use..
And /32 for sure could be used in some configurations.. Where the gateway is different L3 network, but same L2.. So yeah it does have viable setups where it would and could be used. But those are not very common.
Why does my TV when it turn on default to channel 3, there is nothing on channel 3 in my area - is the same sort of question your asking about why does it default to /32
-
@dominicm said in Static IP on WAN results in no connectivity:
Where did you set gateway to none?
Wan interface -> Static IPv4 Configuration -> IPv4 Upstream gateway
I don't see any other gateway option.In that case you would still have a default route to that gateway in the routing table. You just would not have route-to/reply-to on the states. With one WAN it would probably still work fine. With multi-wan you would hit all kinds of problems. Automatic NAT would also break because it would not consider WAN to be a WAN without a gateway set on the interface configuration. Probably other things too but those are the two biggies.
-
@dominicm said in Static IP on WAN results in no connectivity:
From what you said it seems like /32 would never be usable in WAN settings so why would it be the default I do not understand. I would expect a default to be the most common config or something similar.
Probably best to just set the correct netmask and move on. I have brought this up several times. It is not going to change. No matter what the default is set to it will be wrong for most people.
It is incumbent upon the administrator to set the proper interface address and netmask on a new interface.
-
There are some backwoods providers out there that give customers a /32 WAN IP Address with a gateway outside of what would otherwise be their subnet. It's ugly, but it happens.
As @Derelict said, no matter what we pick as the default it will be wrong more often than it is right. Using /32 as the default is less likely to break something than using /1 as the default, and any value in the middle is a wild guess.
