Help? netgate router is receving frequent Gateway alarms & resetting causing lost connections
-
@derelict
@johnpoz I've set the monitor of gateway to NOT action on issues, but it appears that something is happening, extreme lag is occurring on my connection. The below output status actually cased the connection to lag:Oct 1 21:55:24 dpinger WAN_DHCP 75.133.112.1: Alarm latency 9423us stddev 1594us loss 21%
Oct 1 21:56:42 dpinger WAN_DHCP 75.133.112.1: Clear latency 9486us stddev 1748us loss 5%
Oct 1 21:57:19 dpinger WAN_DHCP 75.133.112.1: Alarm latency 9482us stddev 1888us loss 21%
Oct 1 21:59:13 dpinger WAN_DHCP 75.133.112.1: Clear latency 9955us stddev 3258us loss 5%
Oct 1 22:00:09 dpinger WAN_DHCP 75.133.112.1: Alarm latency 9197us stddev 2324us loss 21%
Oct 1 22:01:39 dpinger WAN_DHCP 75.133.112.1: Clear latency 11927us stddev 5882us loss 5%NOt sure what else I need to tweak. My Traffer shaper upload has been set to 7MB/s out of 10MB/s. Still seeing laging, but no disconnections.
-
@r0sebush
My VPN session to my job got disconnected, even though I have the Perfrom Montier Action disabled...:
Oct 2 16:20:07 dpinger WAN_DHCP 75.133.112.1: Alarm latency 7708us stddev 1903us loss 21%
Oct 2 16:21:21 dpinger WAN_DHCP 75.133.112.1: Clear latency 7791us stddev 2353us loss 5% -
Just curious what happens when you disable traffic shaping ? also Ive been a tech at many of the larger telecom's. Did the tech replace you Residential Gateway RG. Ive seen some hardware do stuff like this other router brands. Does it happen around the same time of day or night? if it rains out or gets really hot or any where in between hot or cold days?
-
@snowaks I haven't tried it without traffic shaping. I'm using the Traffic shaping for my VOIP, it performs better & not impacted by other traffic (VPN, Gaming, surfing). I'll try to disable it, but I'd like to make sure my VOIP device is getting the necessary bandwidth, would I use a limiter for that?
The issues occur or appears randomly. Maybe I should have my ISP (Spectrum) re-check the outside "box" on the pole. Since my inside wiring etc. is excellent & they already replaced the coax from the POLE to my house.
Ugh. Too bad the techs at my ISP suck ass. I'd like to get the bottom of this & I'm leaning towards the ISP and something on there end, but hey like to deny shit.
-
Is your WAN DHCP? Since you said you had a Cable provider, it probably is.
If so, check for this: https://redmine.pfsense.org/issues/8507#note-23
-
Yes they do . Also they only give techs 30-60min to fix your problem kinda hard to trouble shoot a random problem that does not show up in 30mins. when it happens again try to connect direct to the RG/CMs and see if the packet loss problems are still there. That way you know where your problem is starting also it could be the RG and resting the connection could also fix it. I had this same problem happen to me 30% packet loss was a bad rg and premise amp. Coax also ages and the stuff from big box stores is cheaper then what charter would install. Have they replaced every thing from the Nid to your CM? if they have it could be something beyond your tap.
PS. What happens when you leave your mtu blank and do not set a value ?
-
@snowaks MTU for the WAN interface is blank by default. Same for LAN. But in the Status/interfaces, they're both 1500.
-
Yesterday, I also noticed that I had UPn-P emabled. But I didn't configure any of the settings. So I disabled that yesterday (along with the disabled Gateway monitoring & monitor actions) and noticed that I didn't have any disconnections.
I also contacted my ISP to get somebody out today 10/6 , but they had a no-show.
I re-enabled the gateway monitoring (without the monitor action). Let's see if we get disconnections today or until they come out in a few days. -
no show sounds like they are overbooking there techs again.
-
@r0sebush update So Tech came out, but again.. they are somewhat useless, but he showed no issue on the line going from house to pole/amplifier, and from model to outside as well. Not enough time spent, due to their time limit allotted per customer.
I wonder if I have a bad wan Port on my netgate sg:2440. I still see disconnections, a little less than before. but nonetheless it happens.
I'm going to enable the opt1 line, and reconfigure firewall NAT etc. and outgoing filters to support opt1. Maybe this will remedy my stuff too..I can't believe with a $200+ dollar router/firewall I have this kind of issue. I may just get another type of route, ubiquiti perhaps? I loved PFSense when I had it running a a custom build PC.... but the sg-2440, ugh... is this a defective model? should I buy the next one they're selling because the 2440 is end of life? WTF.
Oh well.. seems like I'm getting "it" from both ends.. Spectrum, with there lack of movement on getting me some network specialist to help me out VS the Netgate SG-2440 & how it's not really plug in play, but plug in guess how to re-configure your router for your SOHO... :) Maybe they're forcing me to buy one of their pfsense books, which I have....
peace.
-
Highly doubtful it is hardware. You can blame the hardware for ISP issues all you want. Assign WAN to another port and connect the ISP there to check. You don't have to make a new port. Just reassign it to a different hardware interface in Interfaces > Assignments
-
@derelict Tried to change to opt1 port. The only issue I had before I could determine disconnects is that I couldn't nslookup from PC. Looks like DNS wasn't being served correct into my LAN from opt1 or the router.. even after a reboot.
Ugh. This is annoying. Thanks for you input, maybe i can research about getting DNS working on OPT1 -> LAN... WAN->LAN works no issue but still get disconnects. (with our without Traffic shaper enabled or disabled.)
What I don't understand is that even though I have WAN moniter disabled & do do actions, the system still disconnects some sessions ,like my VPN to work. Problem exists, not sure if Specturm support would escalete to manager. Maybe this is what I need, since Tech/linesmen can't help with this kind of problem.
-
@r0sebush Just wondering if this ever got sorted. It would be good to know.
-
Shockingly, the CPU on my system ended up being defective! Lol. I replaced the motherboard/CPU and haven't had a problem ever since.
-
This post is deleted! -
V vdsadmin referenced this topic on
