2 Networks, 2 Gateways, same Router. Routing Question
-
I tried this in my dnsmasq.d config file on the 172.27.3.3 gateway, but it doesn't seem to help:
rev-server=172.27.2.0/24,172.27.2.1 -
In Linux it should be someting like
ip route add 172.27.2.0/24 via 172.27.3.1 dev eth0
Maybe you need to enable IP forwarding
echo 1 > /proc/sys/net/ipv4/ip_forward
But I'm no Raspi guy, maybe those commands need some adjustment.-Rico
-
@Rico : ip forwarding is turned on.
When I entered your 'ip route' command, I got this:root@wormhole:/home/pi# ip route add 172.27.2.0/24 via 172.27.3.1 dev eth0 RTNETLINK answers: File existsSo, it looks like that's already in there. But still no joy.
-
What is the output of
ip route?-Rico
-
@Rico : Lots of stuff!
root@wormhole:/etc/dnsmasq.d# ip route 0.0.0.0/1 via 10.8.0.5 dev tun0 default via 172.27.3.1 dev eth0 metric 202 10.8.0.0/24 via 10.8.0.5 dev tun0 10.8.0.1 via 10.8.0.5 dev tun0 10.8.0.5 dev tun0 proto kernel scope link src 10.8.0.6 10.10.0.0/24 via 10.10.0.5 dev tun2 10.10.0.1 via 10.10.0.5 dev tun2 10.10.0.5 dev tun2 proto kernel scope link src 10.10.0.6 47.149.29.80 via 172.27.3.1 dev eth0 127.0.0.1 via 172.27.3.1 dev eth0 128.0.0.0/1 via 10.8.0.5 dev tun0 136.32.128.65 via 172.27.3.1 dev eth0 136.61.208.161 via 172.27.3.1 dev eth0 139.178.68.38 via 172.27.3.1 dev eth0 139.178.82.59 via 172.27.3.1 dev eth0 172.27.2.0/24 via 172.27.3.1 dev eth0 172.27.3.0/24 dev eth0 proto kernel scope link src 172.27.3.3 metric 202 -
That looks Okay to me, but routing is still asynchronous.
You can either add routes to your endpoints in the 172.27.3.0/24 network or tell pfSense to use 172.27.3.3 as Gateway for 172.27.3.0/24. Check https://docs.netgate.com/pfsense/en/latest/book/routing/static-routes.html-Rico
-
Probably the best and clean solution would be to get rid of the Raspi and use pfSense as your VPN Client.
Check out https://www.netgate.com/resources/videos/openvpn-as-a-wan-on-pfsense.html-Rico
-
@Rico
Ok, so I already had 172.27.3.3 set up as a gateway for the 172.27.3.x Interface.Not sure how to add a route to an endpoint in the 172.27.3.0/24 network, but I'll dig around for how to do that on those devices I need to access from 172.27.2.x
Thanks!
-
I'm still dead.
Can't figure out how to set a static route on hassio or a tasmota device.
And I know my172.27.2.0/24 via 172.27.3.1 dev eth0works, because if I remove that route, then I can't get to anything on the 2.x network from the 3.x network. But I'm still unable to access anything on the 3.x network from the 2.x network.
I'll jump over the the OpenVPN forum and see if they can help. But if anyone has any further ideas, please let me know.
Thanks @Rico !!
-
Here's a tracert from the 172.27.2.x network (my PC) to a device on the 172.27.3.x network (my Home Assistant Server):
C:\Users\DaHai>tracert hassio.asgard Tracing route to hassio.asgard [172.27.3.4] over a maximum of 30 hops: 1 1 ms 1 ms 1 ms bifrost.asgard [172.27.2.1] 2 2 ms 2 ms 1 ms hassio.asgard [172.27.3.4] Trace complete.It routes and complete pretty much instantly, but I can't bring its web page up in my browser.
I get "The site can't be reached"This is the same with any other device on the 3.x network when I try to access it via its web page from the 2.x network.
-
Maybe the iptables.up.rules is set up wrong on the OpenVPN RPI3B+ device?
# Generated by iptables-save v1.4.21 on Tue Nov 29 15:32:04 2016 *nat :PREROUTING ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [25:1612] :POSTROUTING ACCEPT [25:1612] -A POSTROUTING -o tun0 -j MASQUERADE -A POSTROUTING -o tun1 -j MASQUERADE -A POSTROUTING -o tun2 -j MASQUERADE -A POSTROUTING -o eth0 -j MASQUERADE COMMIT # Completed on Tue Nov 29 15:32:04 2016 -
@LeiShen said in 2 Networks, 2 Gateways, same Router. Routing Question:
-A POSTROUTING -o eth0 -j MASQUERADE
Well, it looks like that was the problem. I don't know why it was in there. I don't know what taking it out might break, but now I can get to 3.x devices from the 2.x network!
I'll have to look through my notes to see why it was put in there to begin with...
Cheers!
