Watchguard XTM 5 Series

Fffrank

Once it has booted up, unplug your console cable and plug it back in. That usually works for me for some reason.

tibby

@fffrank
Well That did not work. :) Anything else?

stephenw10

What FreeDOS image are you using exactly?

Still unclear why it's a problem though.

@tibby said in Watchguard XTM 5 Series:

I need freedos to flash the bios so I can boot of the usb :-)

This is incorrect. So unless you want to actually run FreeDOS then just flash the BIOS from pfSense.

Steve

travishauch

@dlucas46 said in Watchguard XTM 5 Series:

Hi all,

For those of you with Xeons that would like coretemp to report the correct temp, you can try this recompiled coretemp module.

I have set the TJMax value to 70c

Remove the png extension and upload to /boot/coretemp2.ko

Chmod 755 coretemp2.ko

In your /boot/loader.conf.local add the following:

coretemp2_load="YES"

Reboot.

You should now have a correct temperature reading. I did this several months ago and its been working fine.

If your CPU is in the same family as L5420 this should also work for you.

coretemp2.ko.png

Is it possible to re-upload this file or is there another way I can get it?

Thank you!

dlucas46

@travishauch here you go: coretemp2.zip

Extract the file and upload to /boot/modules as described in previous post.
You do not need to rename the file this time.

travishauch

@dlucas46 said in Watchguard XTM 5 Series:

@travishauch here you go: coretemp2.zip

Extract the file and upload to /boot/modules as described in previous post.
You do not need to rename the file this time.

Thank you so much! You are a life saver!!!!!!!!!!!!!!!!!!

MajesticUnicorns

Apologies for digging up an old thread.

Recently obtained a XTM510 and it at the moment is running pretty flawlessly with Debian, I've tried everything under the sun and kept coming back to Debian.

Is there any way to get this boxes "ARM" led rocking while under Debian? (probably the wrong place to ask) I have the bios that is way up there in this topic, is there any way I can modify it so that it doesn't say Pfsense1.8 on bootup as its not running that?

I have googled about for weeks to try and get the LED working on the front to no avail. By the seems, it looks like I'd need a windows OS on the box to mod the bios..?

Again, apologies if this is the wrong place, just would like some help, as this seems to be the only place with the most information on it.

stephenw10

The Arm/Disarm LED is connected to the SuperIO chip so there may well be an easier way to do it in Debian.
The modified BIOS sets up the GPIO pins correctly in order to set it to red at that point but the program checks for that and sets it if it has not been.
https://github.com/stephenw10/WGXepc/blob/7f688371751925586d047bc8a2b13bc03e92b64b/WGXepc.c#L1117

So, enable GPIO2 as a GPIO, most of those pins are multifuction.
Set bits 4 and 5 as output.
Set the bits for red, green or off.

Steve

MajesticUnicorns

@stephenw10 I have tried to compile that script to no avail, keeps telling me that there is files missing, I have googled about for those files, still with no avail. In regards to the bios, would I back it up, edit the bios backup on a different PC and then reflash it back to the box?

stephenw10

Yeah I've never tried to use it under Linux. But you should be able to use the data there to set the SuperIO chip some other way. It would not surprise me to find that Linux already has a utiltiy to do it.
Yes, editing the bios and reflashing it is what I did. That's always a risk!

Steve

MajesticUnicorns

@stephenw10 I found SuperIO tool which dumps all of the superIO bits and bobs, no luck to controlling the IO as of yet, although I could just be looking for the wrong thing. If needs be, I can offer someone access to it if anyone wants to dink about on it to try and get the LED working.

Some positive though, I have gotten the system temp sensor to work with lm_sensors, with little to no fan speed with the stock fans and low speed adapters, its rock solid at 65C.

Ive slapped in the dump from the superIO tool below:

superiotool r6637
Found Winbond W83627THF/THG (id=0x82, rev=0x85) at 0x2e
Register dump:
idx 20 21 22 23 24 25 26 28  29 2a 2b 2c 2d 2e 2f
val 82 85 ff fe c6 00 00 00  00 00 00 00 00 00 ff
def 82 NA ff 00 MM 00 MM 00  00 00 MM MM MM 00 00
LDN 0x00 (Floppy)
idx 30 60 61 70 74 f0 f1 f2  f4 f5
val 00 00 00 00 02 0e 00 ff  00 00
def 01 03 f0 06 02 0e 00 ff  00 00
LDN 0x01 (Parallel port)
idx 30 60 61 70 74 f0
val 01 03 78 07 04 3c
def 01 03 78 07 04 3f
LDN 0x02 (COM1)
idx 30 60 61 70 f0
val 01 03 f8 04 00
def 01 03 f8 04 00
LDN 0x03 (COM2)
idx 30 60 61 70 f0 f1
val 01 02 f8 03 00 04
def 01 02 f8 03 00 00
LDN 0x05 (Keyboard)
idx 30 60 61 62 63 70 72 f0
val 01 00 60 00 64 01 0c 82
def 01 00 60 00 64 01 0c 80
LDN 0x07 (GPIO 1, GPIO 5, game port, MIDI port)
idx 30 60 61 62 63 70 f0 f1  f2 f3 f4 f5
val 00 02 01 03 30 09 ff ff  ff ff ff ff
def 00 02 01 03 30 09 ff 00  00 ff 00 00
LDN 0x08 (GPIO 2)
idx 30 f0 f1 f2 f3 f4 f5 f6  f7
val 01 cf 6c 00 00 ff 00 00  00
def 00 ff 00 00 00 RR 00 00  00
LDN 0x09 (GPIO 3, GPIO 4)
idx 30 f0 f1 f2 f3 f4 f5 f6
val 00 ff ff ff 00 ff ff ff
def 00 ff 00 00 00 ff 00 00
LDN 0x0a (ACPI)
idx 30 70 e0 e1 e2 e3 e4 e5  e6 e7 f0 f1 f3 f4 f6 f7  f9 fe ff
val 00 00 01 00 fb 00 30 00  00 00 00 8f 33 00 00 00  00 00 00
def 00 00 00 00 MM MM 00 00  00 00 00 00 00 00 00 00  00 RR RR
LDN 0x0b (Hardware monitor)
idx 30 60 61 70
val 01 0a 00 00
def 00 00 00 00

fmertz

A (long) while back, I integrated the LED control code in a version of the lcdproc sdeclcd driver (the driver that applies to all these Watchguard/Lanner boxes). The intent was to capture all the hard discovery work generously shared by @stephenw10 before it became lost to the big bit bucket in the sky. lcdproc drivers can support a generic output function sent by a client, but it is up to the driver to interpret the number parameter as it sees fit. I meant for it to be portable FreeBSD and Linux code, but it has not been touched in a while. The code seemed a bit complex and not necessarily a great for for an LCD driver, so it was never submitted upstream. Have a look here:

ledsupport branch: server/drivers/sdeclcd.c

MajesticUnicorns

@fmertz Beautiful, I already dinked with that driver to get the mappings correct, must've missed it. How would I control the LED with LCDProc? cant immediately see an option to do so.

fmertz

Well, you would have to create a "client" to the LCDd server, and issue an "output" command, followed by an int. That value would be interpreted as:

/**
 * API: Updates LEDs as per "state". Here, "state" is supposed to contain the sequence the LEDs are
 * to be lit by. We need to support Red, Green and Off. Therefore, we need 2 bits to encode the
 * possible values. So, a 32 bit "state" can host a sequence of 16 separate illuminations. Each
 * group of 2 bits is examined in sequence, as a time slot, each time output is called, and the
 * hardware LEDs are updated accordingly.
 */

Read through the beginning of this: LCDproc Developer's Guide

In short, after starting LCDd with the sdeclcd driver, create a new client:

telnet 127.0.0.1 13666

Then try:

hello
info
output 2863311530
output 1431655765

This was only tested on an older X-Core-e, so adjust your expectations...

stephenw10

Significantly more difficult on the XTM5 because they are not directly addressable GPIOs like they were on the X-E. You need to run a sequence against the SuperIO chip to access it's registers.

Steve

MajesticUnicorns

@fmertz yup, nothing happened :/

chpalmer

I looked through this thread quite quickly and could not find this so reposting just in case.

To put WGXepc64 on an XTM5 box.. and make the arm light go green..

From the console.. each of these commands.

/root
fetch https://github.com/stephenw10/WGXepc/raw/master/WGXepc64
chmod +x WGXepc64

From the GUI..

Use the shellcmd package to execute the command at startup.

System > Packages
Available Packages Tab
Locate Shellcmd
Select the + icon to the right
Confirm install is complete
Services > Shellcmd
Click the + icon to add a new command
Enter in the following
Command: /root/WGXepc64 -l green
Shellcmd Type: Shellcmd
Description: Green Arm Light
Reboot
Confirm

shawl01

Hi Guys,

Asking for a little pointer here. I have been using PFS 2.1.2 on Watchguard X550e for a few years now but wanted to update and noted comments that these units wouldn't run the latest version because of not supporting x64. So I acquired myself a Watchguard xtm 5 (not sure which model it is) in keeping with the red.

I have downloaded the current memstick-serial but have not made any attempts to flash the bios as a number of the posts said this was not necessary.

I am posting my log below but it is sticking at ata2: <ATA channel> at channel 0 on atapci1 on first boot from CF I cannot find any reference to that error and am thinking I must have made some silly mistake so any pointers appreciated.

Thanks in advance
Luke


AMIBIOS(C)2006 American Megatrends, Inc.
MB-7580 Ver.WD0 04/26/2010
CPU : Pentium(R) Dual-Core  CPU      E5300  @ 2.60GHz
 Speed : 2.60 GHz

Press DEL to run Setup (F4 on Remote Keyboard)
Press n if you want to boot from the network
Press F11 for BBS POPUP  (F3 on Remote Keyboard)
The MCH is operating with DDR2 800
DRAM Timing: Tcl:6/Tras:18/Trp:6/Trcd:6/Twr:6/Trfc:52/Twtr:3/Trrd:3/Trtp:3
Initializing USB Controllers .. Done.
2014MB OK

Auto-Detecting Pri Master..IDE Hard Disk
Auto-Detecting 3rd Slave...IDE Hard Disk
             Ultra DMA Mode-5, S.M.A.R.T. Capable and Status OK
                                                                                /boot/config: -S115200 -h
Consoles: serial port
BIOS drive C: is disk0
BIOS drive D: is disk1
BIOS 639kB/2060928kB available memory

FreeBSD/x86 bootstrap loader, Revision 1.1
(Wed Nov 21 08:03:01 EST 2018 root@buildbot2.nyi.netgate.com)
Loading /boot/defaults/loader.conf
-
-
          __
   _ __  / _|___  ___ _ __  ___  ___
  | '_ \| |_/ __|/ _ \ '_ \/ __|/ _ \
  | |_) |  _\__ \  __/ | | \__ \  __/
  | .__/|_| |___/\___|_| |_|___/\___|
  |_|


 +============Welcome to pfSense===========+   __________________________
 |                                         |  /                       ___\
 |  1. Boot Multi User [Enter]             | |                      /`
 |  2. Boot [S]ingle User                  | |                     /    :-|
 |  3. [Esc]ape to loader prompt           | |      _________  ___/    /_ |
 |  4. Reboot                              | |    /` ____   / /__    ___/ |
 |                                         | |   /  /   /  /    /   /     |
 |  Options:                               | |  /  /___/  /    /   /      |
 |  5. [K]ernel: kernel (1 of 2)           | | /   ______/    /   /       |
 |  6. Configure Boot [O]ptions...         | |/   /          /   /        |
 |                                         |     /          /___/         |
 |                                         |    /                         |
 |                                         |   /_________________________/
 +=========================================+

/boot/kernel/kernel text=0x17c1930 data=0xb93d38+0x557b28 syms=[0x8+0x197400+0x8+0x197f72]
Booting...
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2018 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.2-RELEASE-p10 #9 4a2bfdce133(RELENG_2_4_4): Wed May 15 18:54:42 EDT 2019
    root@buildbot1-nyi.netgate.com:/build/ce-crossbuild-244/obj/amd64/ZfGpH5cd/build/ce-crossbuild-244/pfSense/tmp/FreeBSD-src/sys/pfSense amd64
FreeBSD clang version 6.0.0 (tags/RELEASE_600/final 326565) (based on LLVM 6.0.0)
VT(vga): resolution 640x480
CPU: Pentium(R) Dual-Core  CPU      E5300  @ 2.60GHz (2593.56-MHz K8-class CPU)
  Origin="GenuineIntel"  Id=0x1067a  Family=0x6  Model=0x17  Stepping=10
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0xc00e3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,XSAVE,OSXSAVE>
  AMD Features=0x20100800<SYSCALL,NX,LM>
  AMD Features2=0x1<LAHF>
  VT-x: HLT,PAUSE
  TSC: P-state invariant, performance statistics
real memory  = 2147483648 (2048 MB)
avail memory = 1985601536 (1893 MB)
Event timer "LAPIC" quality 100
ACPI APIC Table: <042610 APIC1157>
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
ioapic0 <Version 2.0> irqs 0-23 on motherboard
SMP: AP CPU #1 Launched!
Timecounter "TSC-low" frequency 1296778444 Hz quality 1000
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff80681430, 0) error 1
random: entropy device external interface
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff806814e0, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff80681590, 0) error 1
iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_bss_fw, 0xffffffff806a8460, 0) error 1
iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffffffff806a8510, 0) error 1
iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffffffff806a85c0, 0) error 1
wlan: mac acl policy registered
kbd1 at kbdmux0
netmap: loaded module
module_register_init: MOD_LOAD (vesa, 0xffffffff8120aaa0, 0) error 19
nexus0
vtvga0: <VT VGA driver> on motherboard
cryptosoft0: <software crypto> on motherboard
padlock0: No ACE support.
acpi0: <042610 RSDT1157> on motherboard
acpi0: Power Button (fixed)
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
atrtc0: registered as a time-of-day clock, resolution 1.000000s
Event timer "RTC" frequency 32768 Hz quality 0
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pcib0: _OSC returned error 0x10
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <encrypt/decrypt, network/computer crypto> at device 0.0 (no driver attached)
vgapci0: <VGA-compatible display> port 0x6800-0x6807 mem 0xfe000000-0xfe3fffff,0xd0000000-0xdfffffff irq 16 at device 2.0 on pci0
agp0: <Intel G41 SVGA controller> on vgapci0
agp0: aperture size is 256M, detected 32764k stolen memory
vgapci0: Boot video device
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pcib2: [GIANT-LOCKED]
pci2: <ACPI PCI bus> on pcib2
em0: <Intel(R) PRO/1000 Network Connection 7.6.1-k> port 0x9c00-0x9c1f mem 0xfe6e0000-0xfe6fffff,0xfe6dc000-0xfe6dffff irq 16 at device 0.0 on pci2
em0: Using MSIX interrupts with 3 vectors
em0: Ethernet address: 00:90:7f:9a:09:23
em0: netmap queues/slots: TX 1/1024, RX 1/1024
pcib3: <ACPI PCI-PCI bridge> irq 17 at device 28.1 on pci0
pcib3: [GIANT-LOCKED]
pci3: <ACPI PCI bus> on pcib3
em1: <Intel(R) PRO/1000 Network Connection 7.6.1-k> port 0xac00-0xac1f mem 0xfe7e0000-0xfe7fffff,0xfe7dc000-0xfe7dffff irq 17 at device 0.0 on pci3
em1: Using MSIX interrupts with 3 vectors
em1: Ethernet address: 00:90:7f:9a:09:24
em1: netmap queues/slots: TX 1/1024, RX 1/1024
pcib4: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0
pcib4: [GIANT-LOCKED]
pci4: <ACPI PCI bus> on pcib4
em2: <Intel(R) PRO/1000 Network Connection 7.6.1-k> port 0xbc00-0xbc1f mem 0xfe8e0000-0xfe8fffff,0xfe8dc000-0xfe8dffff irq 18 at device 0.0 on pci4
em2: Using MSIX interrupts with 3 vectors
em2: Ethernet address: 00:90:7f:9a:09:25
em2: netmap queues/slots: TX 1/1024, RX 1/1024
pcib5: <ACPI PCI-PCI bridge> irq 19 at device 28.3 on pci0
pcib5: [GIANT-LOCKED]
pci5: <ACPI PCI bus> on pcib5
em3: <Intel(R) PRO/1000 Network Connection 7.6.1-k> port 0xcc00-0xcc1f mem 0xfe9e0000-0xfe9fffff,0xfe9dc000-0xfe9dffff irq 19 at device 0.0 on pci5
em3: Using MSIX interrupts with 3 vectors
em3: Ethernet address: 00:90:7f:9a:09:26
em3: netmap queues/slots: TX 1/1024, RX 1/1024
pcib6: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pcib6: [GIANT-LOCKED]
pci6: <ACPI PCI bus> on pcib6
em4: <Intel(R) PRO/1000 Network Connection 7.6.1-k> port 0xdc00-0xdc1f mem 0xfeae0000-0xfeafffff,0xfeadc000-0xfeadffff irq 16 at device 0.0 on pci6
em4: Using MSIX interrupts with 3 vectors
em4: Ethernet address: 00:90:7f:9a:09:27
em4: netmap queues/slots: TX 1/1024, RX 1/1024
pcib7: <ACPI PCI-PCI bridge> irq 17 at device 28.5 on pci0
pcib7: [GIANT-LOCKED]
pci7: <ACPI PCI bus> on pcib7
em5: <Intel(R) PRO/1000 Network Connection 7.6.1-k> port 0xec00-0xec1f mem 0xfebe0000-0xfebfffff,0xfebdc000-0xfebdffff irq 17 at device 0.0 on pci7
em5: Using MSIX interrupts with 3 vectors
em5: Ethernet address: 00:90:7f:9a:09:28
em5: netmap queues/slots: TX 1/1024, RX 1/1024
uhci0: <Intel 82801G (ICH7) USB controller USB-A> port 0x7080-0x709f irq 23 at device 29.0 on pci0
usbus0 on uhci0
usbus0: 12Mbps Full Speed USB v1.0
uhci1: <Intel 82801G (ICH7) USB controller USB-B> port 0x7000-0x701f irq 19 at device 29.1 on pci0
usbus1 on uhci1
usbus1: 12Mbps Full Speed USB v1.0
uhci2: <Intel 82801G (ICH7) USB controller USB-C> port 0x6c00-0x6c1f irq 18 at device 29.2 on pci0
usbus2 on uhci2
usbus2: 12Mbps Full Speed USB v1.0
uhci3: <Intel 82801G (ICH7) USB controller USB-D> port 0x6880-0x689f irq 16 at device 29.3 on pci0
usbus3 on uhci3
usbus3: 12Mbps Full Speed USB v1.0
ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0xfe4ff800-0xfe4ffbff irq 23 at device 29.7 on pci0
usbus4: EHCI version 1.0
usbus4 on ehci0
usbus4: 480Mbps High Speed USB v2.0
pcib8: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci8: <ACPI PCI bus> on pcib8
fxp0: <Intel 82801GB (ICH7) 10/100 Ethernet> port 0x8c00-0x8c3f mem 0xfe5ff000-0xfe5fffff irq 20 at device 8.0 on pci8
miibus0: <MII bus> on fxp0
inphy0: <i82562ET 10/100 media interface> PHY 1 on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto, auto-flow
fxp0: Ethernet address: 00:90:7f:9a:09:22
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH7 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 31.1 on pci0
ata0: <ATA channel> at channel 0 on atapci0
atapci1: <Intel ICH7 SATA300 controller> port 0x7c00-0x7c07,0x7880-0x7883,0x7800-0x7807,0x7480-0x7483,0x7400-0x740f mem 0xfe4ffc00-0xfe4fffff irq 19 at device 31.2 on pci0
ata2: <ATA channel> at channel 0 on atapci1

stephenw10

Is that booting from the memstick-serial image written to CF? Or it booted from USB and installed to CF and then booted from that?
IIRC it will only boot from USB if nothing else bootable is present, which is a problem.

Do you want to run from CF or install a SATA drive?

Steve

shawl01

@stephenw10 The first one booted from memstick-serial written to CF I want to install to HD but it isn't getting that far.

Thanks