Routed IPSEC not working

janets

#Konstanti IPv4 and !Pv6 any/any permits are on both side's IPSEC tab.

Konstanti

@janets
192.168.42.1 can ping 172.16.0.2 ?
10.4.96.XXX can ping 172.16.0.1 ??

janets

@Konstanti No, nothing can ping anything. If I try to ping 192.168.42.1 from the other side while running a tcpdump, I can see the packets go out the IPSEC interface. On the other side, I never see the packets on the IPSEC interface, however I do see them on the enc0 interface, so they are getting over there.

I just tried the same configs in the cloud on a couple of VMs and it worked. The firewall that doesn't work has 6 physical interfaces, while the VMs only had 1 + the IPSEC interface. That's really the only major difference I can see.

Konstanti

@janets

what I see is strange - 2 SA almost identical on both sides of the tunnel (only in one case there is no PFS key group , and in the other there is)

There should only be one SA
Try to restart the IPSEC

janets

@Konstanti Actually, the config in the cloud also didn't work. I pinged the wrong IP - dur, sorry, its 5:00 a.m. and I've been up all night. ;-)

I've rebooted the firewalls on both sides, and have the same problem.

janets

@Konstanti Got it to work. If Phase 1's internet protocol is set to IPv4, it breaks. If its set to Dual Stack, it works. Nothing else changed.

janets

It also works in just IPv6 mode. There is something about IPv4 and that config that breaks. It feels like a bug.

janets

Here's what a working vs. a non-working ifconfig looks like.

Working:

ipsec1000: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> metric 0 mtu 1400
tunnel inet6 2600:3c01::f03c:91ff:fe8c:6af1 --> 2001:19f0:8001:688:5400:2ff:fe2c:6deb
inet6 fe80::84b8:2eb3:a617:de8a%ipsec1000 prefixlen 64 scopeid 0x6
inet 172.16.0.1 --> 172.16.0.2 netmask 0xfffffffc
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
reqid: 1000
groups: ipsec

Not working, configured for ipv4, no "tunnel" line in ifconfig.

    ipsec1000: flags=8011<UP,POINTOPOINT,MULTICAST> metric 0 mtu 1500
    inet6 fe80::2e0:67ff:fe13:6324%ipsec1000 prefixlen 64 tentative scopeid 0xb
    inet 10.50.50.1 --> 10.50.50.2 netmask 0xfffffffc
    nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
    reqid: 1000
    groups: ipsec

janets

Now I can't get it working on IPv6 or IPv4. My working config stopped working. For grins, I tried 2.5.0-devel and have the same problem.

janets

@Konstanti

I got it working, but had to do a manual step on each side. Reading the FreeBSD docs, I figured I was missing the tunnel on my ipsec1000 interface:

ipsec1000: flags=8011<UP,POINTOPOINT,MULTICAST> metric 0 mtu 1500
inet6 fe80::84b8:2eb3:a617:de8a%ipsec1000 prefixlen 64 tentative scopeid 0x6
inet 10.20.30.1 --> 10.20.30.2 netmask 0xfffffffc
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
reqid: 1000
groups: ipsec

So I ssh'd in and did this:
ifconfig ipsec1000 inet tunnel 96.126.96.153 73.140.16.217 up

Then on the other side I ran this:
ifconfig ipsec1000 inet tunnel 73.140.16.217 96.126.96.153 up

Everything worked then, and my ifconfig now shows the tunnel:

ipsec1000: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> metric 0 mtu 1500
tunnel inet 96.126.96.153 --> 73.140.16.217
inet6 fe80::84b8:2eb3:a617:de8a%ipsec1000 prefixlen 64 tentative scopeid 0x6
inet 10.20.30.1 --> 10.20.30.2 netmask 0xfffffffc
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
reqid: 1000
groups: ipsec

This seems to be a bug.

janets

The tunnel also didn't route IPv6 over itself, even though I had IPv4 & IPv6 P2s defined. Again, from the commandline I did this on one side:

ifconfig ipsec1000 inet6 2600:3c01:e000:31e::2 prefixlen 112

and this on the other:

ifconfig ipsec1000 inet6 2600:3c01:e000:31e::1 prefixlen 112

Giving me this:

ipsec1000: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> metric 0 mtu 1400
tunnel inet 96.126.96.153 --> 73.140.16.217
inet6 fe80::84b8:2eb3:a617:de8a%ipsec1000 prefixlen 64 scopeid 0x6
inet6 2600:3c01:e000:31e::2 prefixlen 112
inet 10.20.30.1 --> 10.20.30.2 netmask 0xfffffffc
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
reqid: 1000
groups: ipsec

And IPv6 worked.