New Avahi package
-
@dennypage said in New Avahi package:
the point-to-point setting configurable via the GUI.
I meant that while we wait for the 2.0.0_2 version, I have edited the avahi.inc file based on the GitHub changes you had submitted so avahi-deamon.conf will have the allow-point-to-point flag.
-
@sammybernard Sounds good.
-
I can confirm my OpenVPN interfaces, that wouldn't get MDNS before, get it now with v2.0.0_2
Thanks!
(I can control the Chromecast from work once again...) -
@muppet You’re welcome. Glad it’s working for you.
-
Would it be possible to to set a single listen network then select rebroadcast networks?
I have an edge case of having several VLANs, three of which have castable devices, but only one of those devices should be visible on multiple networks.
There is a common area Shield TV (should be visible to it's network, and three others), as well as my bedroom Chromecast (should only be visible on my network) and my roommate has a Chromecast (should only be visible on his network).
Or a a client exclusion by IP address or network?
-
@METDeath Avahi reflection, which is what is used to proxy mDNS, applies to all allowed interfaces. There is no way to limit the advertisements. Remember however that being able to see the device doesn't mean that you can route packets to it. Standard firewall rules still apply.
In other words, you can't hide it but you can easily prevent people from using it.
-
@dennypage Yup, just wanted to make it less of a headache, plus I had my roommate on his VLAN try casting to my Chromecast on my VLAN and it triggered some odd behavior on my phone about my Chromecast.
-
Hi.
Sorry if this is a stupid question.My setup is Lan interface on OPT1 192.168.10.x and wireless on OPT2 10.10.10.x
I have some rules in place to allow specific Lan devices to access the wireless network.
However anything using multicast, Chromecast, printer, scanner, DNLA etc fail.
Would this package help and how would I set it up ?Thanks
-
@TomT said in New Avahi package:
Would this package help and how would I set it up ?
Yep.
Install it - start it - done.
Default setup values do fine for me. Just select all your local LAN interfaces. -
Thanks. I'll give it a go
-
I'm about to set this up.. but had a quick follow up thought.
When this is enabled will it allow OPT -> OPT1 & OPT1 -> OPT ?
Thanks
-
@TomT Avahi reflection allows cross network discovery for all interfaces which it is configured on. That being said, remember Avahi itself offers discovery only. In other words, Avahi will allow you to see that a service is available in another network, but it doesn't mean you will be able to access the service. Access is controlled by firewall rules.
-
Hello,
Sorry if I don't post in the right place.
We have a site-to-site vpn tunnel (openvpn) between 2 pfSense instances. It is operational. We want to be able to use the Mac OS Messages app (formerly iChat) between our 2 LANs. We installed and configured Avahi 2.0.0_2 on each side. In the friends list, we can't see the remote stations. Likewise, Discovery app only lists local stations. The firewall is configured to allow to see (any ports) the remote stations on each side: LAN 192.168.10.0/24 and LAN 192.168.60.0/24.
We don't see why it doesn't work.
However, a post indicates that it is possible: https://forum.netgate.com/topic/18877/routing-apple-bonjour
Thanks in advance for any help. We aren't geeks !
Best regards from France.Here is the Avahi configuration used:
[Server]
allow-interfaces = RE0
allow-Point-to-Point = yes
use-ipv4 = yes
use-ipv6 = no
enable-dbus = no
Cache-entries-max = 0[Wide-area]
enable-wide-area = no[Publish]
disable-publishing = yes
publish-addresses = No
publish-hinfo = no
publish-workstation = no
publish-domain = No.
publish-yyyy-on-ipv4 = no
publish-on-a-ipv6 = no
disable-user-service-publishing = yes[Reflector]
enable-reflector = yes -
@Bernard-Senior said in New Avahi package:
Here is the Avahi configuration used:
[Server]
allow-interfaces = RE0You only have a single allowed interface. Multiple interfaces are required for Avahi reflection to have anything to do. In other words, you need to have your LAN and your tunnel in the allowed list on both sides.
When I have a minute, I'll add a check to the UI to prevent enabling reflection if only one allowed interface is defined.
-
Thank you very much for your answer.
I added and enabled a virtual interface for the vpn tunnel : ovpnc1.
The configuration is now :
[server]
allow-interfaces=re0,ovpnc1
Is it better ? I have to enter the same config at the other end of the tunnel.I tried this configuration but when I added opvnc1 on the second pfSense, I lost the connection of the tunnel !
Presently, the VPN connection go out through a WAN 4G interface to a VPN server hosted by a small VPS on the internet.
I think it's safer for us to talk to the person who installed the VPN tunnel !
Thank you for your help. -
Does anyone know a good windows mDNS browser i can use, there are suggestions above for mac and linux but i can't seem to find anything for windows.
I am struggling casting to my samsung smart tv and my firestick and can't print to my epson printer. Was hoping to use a discovery tool to see what is actually being found and try and work from there.
-
EDIT: Well, a lesson if anyone faces a similar issue. I am running Unifi APs and the Block LAN to WLAN Multicast and Broadcast Data option was the culprit. It's all working now. :)
I am having problems on a Mac detecting a NAS Time Machine share (Bonjour/AFP) protocol. I had this working prior with an EdgeRouter and mDNS but am not having much luck on pfSense. I have posted about it here: https://forum.netgate.com/topic/147061/avahi-synology-shares-afp
Appreciate if anyone can help out.
-
@edz said in New Avahi package:
Appreciate if anyone can help out.
Did you check :
@edz said in New Avahi package:
Unifi APs and the Block LAN to WLAN Multicast and Broadcast Data option
and what if this AP is filtering also the other way around ?
No WLAN to LAN "cast" traffic and Avahi will not see anything ?! -
Hoping someone can help me out with this, trying to use Avahi to AirPrint across two VLANs...
Interfaces
LAN (default VLAN1) - 10.10.1.0/24 (this is where my iPhone and all other devices are)
BLACKHOLE (VLAN40) - 10.10.40.0/24 (this is where the wireless printer lives, this VLAN has no access back to other VLANs)The request to print looks like this.
LAN ------print request------> BLACKHOLEFrom my LAN (10.10.1.0/24), I can ping the printer (10.10.40.12) and access the web interface, so I know the VLAN setup is working. Below is the firewall setup for my LAN.
However, from my iPhone (on the LAN network), when I try to print, it can't find the printer via AirPrint (even though I can ping the printer from my iPhone). Here is my Avahi setup, what am I missing?
My wireless is through UniFI, so I have made sure this setting is unchecked on all of my wireless networks.
I've also made sure this is checked on my LAN network's wifi.
-
@logan5247 Is mDNS enabled on the printer?
Before trying to diagnose issues across subnets, you want to confirm that it works within the same net. Join the blackhole network with your iPhone and confirm that AirPrint works.
