Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    IPV6 setup with Hyperoptic (UK ISP)

    Scheduled Pinned Locked Moved IPv6
    27 Posts 7 Posters 8.9k Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Y
      yellowbrick
      last edited by

      On 1. above, Hyperoptic support have responded the IPv6 gateway will be assigned using SLAAC only, so they cannot tell me a non-link-local address to use.

      On 2.: still cannot ping using IPv6 from the pfSense router...clients on the LAN are working fine (i.e. can ping6 from a client on LAN to anywhere).

      Point to note, IPv4 out from pfSense works fine...

      Any ideas?

      TIA

      1 Reply Last reply Reply Quote 0
      • M
        msf2000
        last edited by msf2000

        @yellowbrick said in IPV6 setup with Hyperoptic (UK ISP):

        /56 PD

        Did the ISP assign you an IPv6 subnet of size /56? That seems confusing since the comment you made later that the ISP is using SLAAC. If true, that would explain why DHCPv6 on the WAN is not working.

        Also, have you tried setting the WAN interface "IPv6 configuration type" to "SLAAC"?

        1 Reply Last reply Reply Quote 0
        • Y
          yellowbrick
          last edited by yellowbrick

          Yes, pfSense is definitely getting a /56 PD, from the logs (manually blanked out):

          Sep 30 07:22:22 dhcp6c 98391 IA_PD prefix: 2a01:xxxx:xxxx:xxxx::/56 pltime=72000 vltime=86400
          Sep 30 07:22:22 dhcp6c 98391 get DHCP option IA_PD prefix, len 25
          Sep 30 07:22:22 dhcp6c 98391 IA_PD: ID=0, T1=43200, T2=64800
          Sep 30 07:22:22 dhcp6c 98391 get DHCP option IA_PD, len 41
          Sep 30 07:22:22 dhcp6c 98391 set IA_PD
          Sep 30 07:22:22 dhcp6c 98391 set IA_PD prefix
          
          

          Also, both LAN and OPT1 interfaces are set to track WAN with prefix ID 0 and 1 respectively. They both are working with clients getting correct IPv6 addresses in the correct /64 subnet.

          I agree the 'SLAAC' comment is confusing, but my ISP actually says the upstream gateway for the WAN interface (which gets a valid WAN IPv6 address not in in /56 PD) is only assigned via SLAAC. However, I suspect they mean link-local discovery (?) as the IPv6 gateway is an fe80:: address.

          Also, as I mentioned, clients can exit using IPv6 without any problems...just the pfSense box itself cannot!

          I have not tried setting WAN to SLAAC...will try it now.

          Thanks.

          1 Reply Last reply Reply Quote 0
          • Y
            yellowbrick
            last edited by

            Setting the WAN interface to SLAAC results IPv6 not working at all...no WAN IPv6, no LAN/OPT IPv6 addresses, cannot route out, etc.

            Changing WAN back to DHCPv6 means WAN gets a /128, /56 PD is received, and LAN/OPT clients start working.

            strange...

            JKnottJ 1 Reply Last reply Reply Quote 0
            • M
              msf2000
              last edited by

              Ah, I missed the part about LAN being set to track the WAN interface.... Yeah, let's leave that as is.

              Sounds like the ISP's DHCPv6 server is giving out ranges (ra) but not assignments (managed), or possibly routing is not correct...
              What version of pfSense are you running? People (here) have been posting DHCPv6 problems with the latest version 2.4.4.

              1 Reply Last reply Reply Quote 0
              • Y
                yellowbrick
                last edited by yellowbrick

                I am running 2.4.4.

                Just to point out again, all the clients on LAN and OPT do get addresses in the correct /64 and are able to ping6 out to the net.

                It's just the pfSense box (SG-3100) itself that cannot exit out to WAN using IPv6 (ssh'd into SG-3100).

                1 Reply Last reply Reply Quote 0
                • M
                  msf2000
                  last edited by

                  OK, now I suspect the firewall.
                  If you change the FW rule on the LAN from 'LAN Net' to 'any', does that make it work? If not, enable logging on all WAN/LAN rules (and the default rules), and see if the FW logs turn up any clues.

                  1 Reply Last reply Reply Quote 0
                  • JKnottJ
                    JKnott @yellowbrick
                    last edited by

                    @yellowbrick said in IPV6 setup with Hyperoptic (UK ISP):

                    Setting the WAN interface to SLAAC results IPv6 not working at all...no WAN IPv6, no LAN/OPT IPv6 addresses, cannot route out, etc.
                    Changing WAN back to DHCPv6 means WAN gets a /128, /56 PD is received, and LAN/OPT clients start working.
                    strange...

                    That's the way mine works. DHCPv6-PD assigns an address to the WAN interface and supplies the prefix for the LANs.

                    PfSense running on Qotom mini PC
                    i5 CPU, 4 GB memory, 32 GB SSD & 4 Intel Gb Ethernet ports.
                    UniFi AC-Lite access point

                    I haven't lost my mind. It's around here...somewhere...

                    1 Reply Last reply Reply Quote 0
                    • Y
                      yellowbrick
                      last edited by

                      I don't see anything in the logs indicating blocked packets on WAN or LAN.

                      Not sure if this has anything to do with it, but I do have my WAN using a MAC clone from the ISP's router. Without this, I am not able to get a DHCPv6 address on WAN at all.

                      1 Reply Last reply Reply Quote 0
                      • A
                        adhodgson
                        last edited by

                        Hi,

                        Did you ever get this sorted? I am getting the same issue (though I didn't clone any MAC or anything else). Clients on the LAN are getting IPV6 ok, but the pfSense box itself cannot go out via it's WAN address to the Internet over IPV6. I suspect some type of routing on the Hyperoptic side is broken.

                        Andrew.

                        Y 1 Reply Last reply Reply Quote 0
                        • DerelictD
                          Derelict LAYER 8 Netgate
                          last edited by

                          So you're on this same ISP?

                          Chattanooga, Tennessee, USA
                          A comprehensive network diagram is worth 10,000 words and 15 conference calls.
                          DO NOT set a source address/port in a port forward or firewall rule unless you KNOW you need it!
                          Do Not Chat For Help! NO_WAN_EGRESS(TM)

                          1 Reply Last reply Reply Quote 0
                          • JKnottJ
                            JKnott @yellowbrick
                            last edited by

                            @yellowbrick said in IPV6 setup with Hyperoptic (UK ISP):

                            On the WAN interface, I do not get a ‘real’ IPV6 Gateway. The WAN gets a Link Local IPv6 Gateway only (fe80:: …) . (This was true even with the Hyperoptic ZTE router). Is this ‘normal’?

                            I just noticed this. If pfSense doesn't have a WAN address, other than link local, it can't communicate with anything. On my system, I have a /128 WAN address. Devices on the LAN will still work fine though, as that /128 address is not used for routing.

                            PfSense running on Qotom mini PC
                            i5 CPU, 4 GB memory, 32 GB SSD & 4 Intel Gb Ethernet ports.
                            UniFi AC-Lite access point

                            I haven't lost my mind. It's around here...somewhere...

                            1 Reply Last reply Reply Quote 0
                            • DerelictD
                              Derelict LAYER 8 Netgate
                              last edited by

                              Poster is not saying there is no IPv6 GUA address on WAN, just that the gateway is link-local, which is normal.

                              Chattanooga, Tennessee, USA
                              A comprehensive network diagram is worth 10,000 words and 15 conference calls.
                              DO NOT set a source address/port in a port forward or firewall rule unless you KNOW you need it!
                              Do Not Chat For Help! NO_WAN_EGRESS(TM)

                              JKnottJ 1 Reply Last reply Reply Quote 0
                              • Y
                                yellowbrick @adhodgson
                                last edited by

                                @adhodgson
                                I am getting pretty much the same as you:
                                -WAN gets a /128 GUA
                                -WAN gateway is a LLA
                                -LAN clients can ping6 OK
                                -Firewall itself cannot ping6 (other than to WAN gateway)

                                I gave up on trying to figure it out...pfSense updates were slow, as IPv6 is preferred so it has to fail before going to IPv4. I fixed this by preferring IPv4 in System->Advanced->Networking

                                Will try to find time to dig in deeper...

                                1 Reply Last reply Reply Quote 0
                                • A
                                  adhodgson
                                  last edited by

                                  Hi,

                                  Yes I am using the same ISP as the original poster. Just for reference my WAN output is:

                                  WAN Interface (wan, igb0)
                                  Status: up
                                  DHCP: up
                                  MAC Address: 00:1a:8c:4b:36:6c
                                  IPv4 Address: 88.98.222.211
                                  Subnet mask IPv4: 255.255.255.248
                                  Gateway IPv4: 88.98.222.209
                                  IPv6 Link Local: fe80::21a:8cff:fe4b:366c%igb0
                                  IPv6 Address: 2a01:4b00:367b:5801:641a:32ef:9a9f:817a
                                  Subnet mask IPv6: 128
                                  Gateway IPv6: fe80::2ab4:48ff:fe87:c9fb
                                  DNS servers: 127.0.0.1, 188.172.144.120, 141.0.144.64
                                  MTU: 1500
                                  Media: 1000baseT <full-duplex>

                                  I believe this is normal, the problem is that for some reason the IP address 2a01:4b00:367b:5801:641a:32ef:9a9f:817a is not being routed correctly. I can see traffic going to the default gateway on a packet capture, but no return traffic, and if I try and ping that host from an external interface the traffic doesn't even seem to be visible at the pfSense box. My fix is to do what the original poster has done, prefer IPV4 to IPV6 connectivity.

                                  I am still probably going to raise a case with the ISP in the first instance but am not hugely hopeful of a fix until I do more work at my end. The main question I want to get an answer to is whether they expect traffic on this WAN address to be routable or not, because in the situation where you have the customer provided router, you probably wouldn't even see this scenario in day-to-day operation, we are only seeing it because we are trying to access sites on the firewall box itself.

                                  Thanks.
                                  Andrew.

                                  JKnottJ NogBadTheBadN 2 Replies Last reply Reply Quote 0
                                  • JKnottJ
                                    JKnott @Derelict
                                    last edited by

                                    @Derelict said in IPV6 setup with Hyperoptic (UK ISP):

                                    Poster is not saying there is no IPv6 GUA address on WAN, just that the gateway is link-local, which is normal.

                                    He also said "On the WAN interface, I do not get a ‘real’ IPV6 Gateway." and he can't ping from pfSense, but can from the LAN. He won't be able to ping very far using only a link local address.

                                    PfSense running on Qotom mini PC
                                    i5 CPU, 4 GB memory, 32 GB SSD & 4 Intel Gb Ethernet ports.
                                    UniFi AC-Lite access point

                                    I haven't lost my mind. It's around here...somewhere...

                                    1 Reply Last reply Reply Quote 0
                                    • JKnottJ
                                      JKnott @adhodgson
                                      last edited by

                                      @adhodgson said in IPV6 setup with Hyperoptic (UK ISP):

                                      I believe this is normal, the problem is that for some reason the IP address 2a01:4b00:367b:5801:641a:32ef:9a9f:817a is not being routed correctly. I can see traffic going to the default gateway on a packet capture, but no return traffic, and if I try and ping that host from an external interface the traffic doesn't even seem to be visible at the pfSense box. My fix is to do what the original poster has done, prefer IPV4 to IPV6 connectivity.

                                      What does traceroute show? If you can, also try a traceroute to your WAN address from elsewhere. I tethered to my cell phone for that.

                                      PfSense running on Qotom mini PC
                                      i5 CPU, 4 GB memory, 32 GB SSD & 4 Intel Gb Ethernet ports.
                                      UniFi AC-Lite access point

                                      I haven't lost my mind. It's around here...somewhere...

                                      1 Reply Last reply Reply Quote 0
                                      • A
                                        adhodgson
                                        last edited by

                                        I can ping and trace route to the address from inside the LAN but that should be expected behaviour as pfSense knows about that address. Trace route from outside stops well before the Hyperoptic routers:

                                        andrew@samwise:~$ traceroute 2a01:4b00:367b:5801:641a:32ef:9a9f:817a
                                        traceroute to 2a01:4b00:367b:5801:641a:32ef:9a9f:817a (2a01:4b00:367b:5801:641a:32ef:9a9f:817a), 30 hops max, 80 byte packets
                                        1 2001-41c8-0051-0500-0000-0000-0000-0003.no-reverse-dns-set.uk0.bigv.io (2001:41c8:51:500::3) 1.892 ms 1.917 ms 1.834 ms
                                        2 4008.be1.cr4.man.bytemark.co.uk (2001:41c8:2000:4::1) 1.528 ms 1.524 ms 1.589 ms
                                        3 2001:1b40:f900:8a61::1:1 (2001:1b40:f900:8a61::1:1) 1.100 ms 1.293 ms 1.259 ms
                                        4 be16.asr01.ld5.as20860.net (2001:1b40:f000:10a:202::1) 12.704 ms 12.436 ms 12.555 ms
                                        5 * * *
                                        [...]
                                        30 * * *

                                        Andrew.

                                        JKnottJ 1 Reply Last reply Reply Quote 0
                                        • JKnottJ
                                          JKnott @adhodgson
                                          last edited by

                                          @adhodgson said in IPV6 setup with Hyperoptic (UK ISP):

                                          I can ping and trace route to the address from inside the LAN but that should be expected behaviour as pfSense knows about that address. Trace route from outside stops well before the Hyperoptic routers:

                                          Then it's a problem with the ISP. They're supposed to advertise the prefix via a routing protocol such as OSPF. If they don't do that, then the rest of the world can't reach it. You can use ping6 -S <source address> to force the ping from the LAN interface, which does work.

                                          This indicates one of the differences between IPv4 & IPv6. With IPv4, you need a routeable address on the WAN interface. With IPv6, link local is often used. To reach pfSense from elsewhere, you can use any routeable address on the box. In my case, I have a /128 address on the WAN interface. In your case, you have to use the LAN address.

                                          PfSense running on Qotom mini PC
                                          i5 CPU, 4 GB memory, 32 GB SSD & 4 Intel Gb Ethernet ports.
                                          UniFi AC-Lite access point

                                          I haven't lost my mind. It's around here...somewhere...

                                          A 1 Reply Last reply Reply Quote 0
                                          • NogBadTheBadN
                                            NogBadTheBad @adhodgson
                                            last edited by NogBadTheBad

                                            This post is deleted!
                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.