Watchguard XTM 5 Series

stephenw10

Significantly more difficult on the XTM5 because they are not directly addressable GPIOs like they were on the X-E. You need to run a sequence against the SuperIO chip to access it's registers.

Steve

MajesticUnicorns

@fmertz yup, nothing happened :/

chpalmer

I looked through this thread quite quickly and could not find this so reposting just in case.

To put WGXepc64 on an XTM5 box.. and make the arm light go green..

From the console.. each of these commands.

/root
fetch https://github.com/stephenw10/WGXepc/raw/master/WGXepc64
chmod +x WGXepc64

From the GUI..

Use the shellcmd package to execute the command at startup.

System > Packages
Available Packages Tab
Locate Shellcmd
Select the + icon to the right
Confirm install is complete
Services > Shellcmd
Click the + icon to add a new command
Enter in the following
Command: /root/WGXepc64 -l green
Shellcmd Type: Shellcmd
Description: Green Arm Light
Reboot
Confirm

shawl01

Hi Guys,

Asking for a little pointer here. I have been using PFS 2.1.2 on Watchguard X550e for a few years now but wanted to update and noted comments that these units wouldn't run the latest version because of not supporting x64. So I acquired myself a Watchguard xtm 5 (not sure which model it is) in keeping with the red.

I have downloaded the current memstick-serial but have not made any attempts to flash the bios as a number of the posts said this was not necessary.

I am posting my log below but it is sticking at ata2: <ATA channel> at channel 0 on atapci1 on first boot from CF I cannot find any reference to that error and am thinking I must have made some silly mistake so any pointers appreciated.

Thanks in advance
Luke


AMIBIOS(C)2006 American Megatrends, Inc.
MB-7580 Ver.WD0 04/26/2010
CPU : Pentium(R) Dual-Core  CPU      E5300  @ 2.60GHz
 Speed : 2.60 GHz

Press DEL to run Setup (F4 on Remote Keyboard)
Press n if you want to boot from the network
Press F11 for BBS POPUP  (F3 on Remote Keyboard)
The MCH is operating with DDR2 800
DRAM Timing: Tcl:6/Tras:18/Trp:6/Trcd:6/Twr:6/Trfc:52/Twtr:3/Trrd:3/Trtp:3
Initializing USB Controllers .. Done.
2014MB OK

Auto-Detecting Pri Master..IDE Hard Disk
Auto-Detecting 3rd Slave...IDE Hard Disk
             Ultra DMA Mode-5, S.M.A.R.T. Capable and Status OK
                                                                                /boot/config: -S115200 -h
Consoles: serial port
BIOS drive C: is disk0
BIOS drive D: is disk1
BIOS 639kB/2060928kB available memory

FreeBSD/x86 bootstrap loader, Revision 1.1
(Wed Nov 21 08:03:01 EST 2018 root@buildbot2.nyi.netgate.com)
Loading /boot/defaults/loader.conf
-
-
          __
   _ __  / _|___  ___ _ __  ___  ___
  | '_ \| |_/ __|/ _ \ '_ \/ __|/ _ \
  | |_) |  _\__ \  __/ | | \__ \  __/
  | .__/|_| |___/\___|_| |_|___/\___|
  |_|


 +============Welcome to pfSense===========+   __________________________
 |                                         |  /                       ___\
 |  1. Boot Multi User [Enter]             | |                      /`
 |  2. Boot [S]ingle User                  | |                     /    :-|
 |  3. [Esc]ape to loader prompt           | |      _________  ___/    /_ |
 |  4. Reboot                              | |    /` ____   / /__    ___/ |
 |                                         | |   /  /   /  /    /   /     |
 |  Options:                               | |  /  /___/  /    /   /      |
 |  5. [K]ernel: kernel (1 of 2)           | | /   ______/    /   /       |
 |  6. Configure Boot [O]ptions...         | |/   /          /   /        |
 |                                         |     /          /___/         |
 |                                         |    /                         |
 |                                         |   /_________________________/
 +=========================================+

/boot/kernel/kernel text=0x17c1930 data=0xb93d38+0x557b28 syms=[0x8+0x197400+0x8+0x197f72]
Booting...
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2018 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.2-RELEASE-p10 #9 4a2bfdce133(RELENG_2_4_4): Wed May 15 18:54:42 EDT 2019
    root@buildbot1-nyi.netgate.com:/build/ce-crossbuild-244/obj/amd64/ZfGpH5cd/build/ce-crossbuild-244/pfSense/tmp/FreeBSD-src/sys/pfSense amd64
FreeBSD clang version 6.0.0 (tags/RELEASE_600/final 326565) (based on LLVM 6.0.0)
VT(vga): resolution 640x480
CPU: Pentium(R) Dual-Core  CPU      E5300  @ 2.60GHz (2593.56-MHz K8-class CPU)
  Origin="GenuineIntel"  Id=0x1067a  Family=0x6  Model=0x17  Stepping=10
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0xc00e3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,XSAVE,OSXSAVE>
  AMD Features=0x20100800<SYSCALL,NX,LM>
  AMD Features2=0x1<LAHF>
  VT-x: HLT,PAUSE
  TSC: P-state invariant, performance statistics
real memory  = 2147483648 (2048 MB)
avail memory = 1985601536 (1893 MB)
Event timer "LAPIC" quality 100
ACPI APIC Table: <042610 APIC1157>
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
ioapic0 <Version 2.0> irqs 0-23 on motherboard
SMP: AP CPU #1 Launched!
Timecounter "TSC-low" frequency 1296778444 Hz quality 1000
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff80681430, 0) error 1
random: entropy device external interface
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff806814e0, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff80681590, 0) error 1
iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_bss_fw, 0xffffffff806a8460, 0) error 1
iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffffffff806a8510, 0) error 1
iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffffffff806a85c0, 0) error 1
wlan: mac acl policy registered
kbd1 at kbdmux0
netmap: loaded module
module_register_init: MOD_LOAD (vesa, 0xffffffff8120aaa0, 0) error 19
nexus0
vtvga0: <VT VGA driver> on motherboard
cryptosoft0: <software crypto> on motherboard
padlock0: No ACE support.
acpi0: <042610 RSDT1157> on motherboard
acpi0: Power Button (fixed)
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
atrtc0: registered as a time-of-day clock, resolution 1.000000s
Event timer "RTC" frequency 32768 Hz quality 0
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pcib0: _OSC returned error 0x10
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <encrypt/decrypt, network/computer crypto> at device 0.0 (no driver attached)
vgapci0: <VGA-compatible display> port 0x6800-0x6807 mem 0xfe000000-0xfe3fffff,0xd0000000-0xdfffffff irq 16 at device 2.0 on pci0
agp0: <Intel G41 SVGA controller> on vgapci0
agp0: aperture size is 256M, detected 32764k stolen memory
vgapci0: Boot video device
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pcib2: [GIANT-LOCKED]
pci2: <ACPI PCI bus> on pcib2
em0: <Intel(R) PRO/1000 Network Connection 7.6.1-k> port 0x9c00-0x9c1f mem 0xfe6e0000-0xfe6fffff,0xfe6dc000-0xfe6dffff irq 16 at device 0.0 on pci2
em0: Using MSIX interrupts with 3 vectors
em0: Ethernet address: 00:90:7f:9a:09:23
em0: netmap queues/slots: TX 1/1024, RX 1/1024
pcib3: <ACPI PCI-PCI bridge> irq 17 at device 28.1 on pci0
pcib3: [GIANT-LOCKED]
pci3: <ACPI PCI bus> on pcib3
em1: <Intel(R) PRO/1000 Network Connection 7.6.1-k> port 0xac00-0xac1f mem 0xfe7e0000-0xfe7fffff,0xfe7dc000-0xfe7dffff irq 17 at device 0.0 on pci3
em1: Using MSIX interrupts with 3 vectors
em1: Ethernet address: 00:90:7f:9a:09:24
em1: netmap queues/slots: TX 1/1024, RX 1/1024
pcib4: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0
pcib4: [GIANT-LOCKED]
pci4: <ACPI PCI bus> on pcib4
em2: <Intel(R) PRO/1000 Network Connection 7.6.1-k> port 0xbc00-0xbc1f mem 0xfe8e0000-0xfe8fffff,0xfe8dc000-0xfe8dffff irq 18 at device 0.0 on pci4
em2: Using MSIX interrupts with 3 vectors
em2: Ethernet address: 00:90:7f:9a:09:25
em2: netmap queues/slots: TX 1/1024, RX 1/1024
pcib5: <ACPI PCI-PCI bridge> irq 19 at device 28.3 on pci0
pcib5: [GIANT-LOCKED]
pci5: <ACPI PCI bus> on pcib5
em3: <Intel(R) PRO/1000 Network Connection 7.6.1-k> port 0xcc00-0xcc1f mem 0xfe9e0000-0xfe9fffff,0xfe9dc000-0xfe9dffff irq 19 at device 0.0 on pci5
em3: Using MSIX interrupts with 3 vectors
em3: Ethernet address: 00:90:7f:9a:09:26
em3: netmap queues/slots: TX 1/1024, RX 1/1024
pcib6: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pcib6: [GIANT-LOCKED]
pci6: <ACPI PCI bus> on pcib6
em4: <Intel(R) PRO/1000 Network Connection 7.6.1-k> port 0xdc00-0xdc1f mem 0xfeae0000-0xfeafffff,0xfeadc000-0xfeadffff irq 16 at device 0.0 on pci6
em4: Using MSIX interrupts with 3 vectors
em4: Ethernet address: 00:90:7f:9a:09:27
em4: netmap queues/slots: TX 1/1024, RX 1/1024
pcib7: <ACPI PCI-PCI bridge> irq 17 at device 28.5 on pci0
pcib7: [GIANT-LOCKED]
pci7: <ACPI PCI bus> on pcib7
em5: <Intel(R) PRO/1000 Network Connection 7.6.1-k> port 0xec00-0xec1f mem 0xfebe0000-0xfebfffff,0xfebdc000-0xfebdffff irq 17 at device 0.0 on pci7
em5: Using MSIX interrupts with 3 vectors
em5: Ethernet address: 00:90:7f:9a:09:28
em5: netmap queues/slots: TX 1/1024, RX 1/1024
uhci0: <Intel 82801G (ICH7) USB controller USB-A> port 0x7080-0x709f irq 23 at device 29.0 on pci0
usbus0 on uhci0
usbus0: 12Mbps Full Speed USB v1.0
uhci1: <Intel 82801G (ICH7) USB controller USB-B> port 0x7000-0x701f irq 19 at device 29.1 on pci0
usbus1 on uhci1
usbus1: 12Mbps Full Speed USB v1.0
uhci2: <Intel 82801G (ICH7) USB controller USB-C> port 0x6c00-0x6c1f irq 18 at device 29.2 on pci0
usbus2 on uhci2
usbus2: 12Mbps Full Speed USB v1.0
uhci3: <Intel 82801G (ICH7) USB controller USB-D> port 0x6880-0x689f irq 16 at device 29.3 on pci0
usbus3 on uhci3
usbus3: 12Mbps Full Speed USB v1.0
ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0xfe4ff800-0xfe4ffbff irq 23 at device 29.7 on pci0
usbus4: EHCI version 1.0
usbus4 on ehci0
usbus4: 480Mbps High Speed USB v2.0
pcib8: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci8: <ACPI PCI bus> on pcib8
fxp0: <Intel 82801GB (ICH7) 10/100 Ethernet> port 0x8c00-0x8c3f mem 0xfe5ff000-0xfe5fffff irq 20 at device 8.0 on pci8
miibus0: <MII bus> on fxp0
inphy0: <i82562ET 10/100 media interface> PHY 1 on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto, auto-flow
fxp0: Ethernet address: 00:90:7f:9a:09:22
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH7 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 31.1 on pci0
ata0: <ATA channel> at channel 0 on atapci0
atapci1: <Intel ICH7 SATA300 controller> port 0x7c00-0x7c07,0x7880-0x7883,0x7800-0x7807,0x7480-0x7483,0x7400-0x740f mem 0xfe4ffc00-0xfe4fffff irq 19 at device 31.2 on pci0
ata2: <ATA channel> at channel 0 on atapci1

stephenw10

Is that booting from the memstick-serial image written to CF? Or it booted from USB and installed to CF and then booted from that?
IIRC it will only boot from USB if nothing else bootable is present, which is a problem.

Do you want to run from CF or install a SATA drive?

Steve

shawl01

@stephenw10 The first one booted from memstick-serial written to CF I want to install to HD but it isn't getting that far.

Thanks

stephenw10

What exact image did you use? You should be using, for example, this:
https://nyifiles.pfsense.org/mirror/downloads/pfSense-CE-memstick-serial-2.4.4-RELEASE-p3-amd64.img.gz

Does it boot further if you disconnect the SATA drive?

Steve

shawl01

@stephenw10 My exact filename is pfSense-CE-memstick-serial-2.4.4-RELEASE-p3-amd64.img it was downloaded from https://www.pfsense.org/download/ and selecting the boxes AMD64, USB Memstick Installer, Serial, New York.

I download on a mac so it may automatically unzip the file for me. Should I try the image location you suggest?

If I disconnect the HHD it is exactly the same, in fact I thought that was the issue at first as I booted without HDD attached.

Thanks

samtap

In my experience, you have to flash the modified bios since the official bios is locked and many options can't be changed i.e. the boot device preferences, by default it only boots from CF even if nothing else is attached. I was able to run the pfSense installer from CF and install to SATA disks, but it still refused to boot. You'll need the bios firmware, flash tool and some OS, boot that from CF just to flash the bios (you could likely even use the factory firmware and serial console for it, if you can find a compatible flash tool binary). After flashing lots of options that used to be read-only can now be changed and you can boot from SATA, USB etc. In addition with the modified bios pfSense can use front LCD to display some useful stats.

shawl01

@samtap Ok, I thought that may be thew case, but many people on here have said to flash the bios from within pfsense, but mine will not even get that far.

@stephenw10 As you were asking about the image i tried making it on a Win7 PC incase it was the mac no writing it correctly to the CF but I get exactly the same response and it freezes in the same spot. Could my putty settings be wrong and it freezes once it goes into the setup program??

Thanks

samtap

I think there must be subtle differences between different xtm series and maybe even hardware revisions. For example people claim it boots USB/SATA once you disconnect CF reader, I believe them but for my xtm5 it didn't work like that.

By the way, are you sure it freezes during boot? It might be just the serial console settings that change after it gets through POST and starts booting the OS...

shawl01

Ok.

So I went a step further and used my CF card and HDD connected to a VM and installed pfsense onto the hdd.

Tried hdd in xtm and hdd booted fine unto the exact same point.

So put the hdd back into the vm and booted the hdd and completed the setup with the network card configuration. and then restarted pfsense a couple of times to make sure it was booting all the way through with no questions hoping up. Then put hdd back into xtm and it boots up still to the exact same point, but I have my laptop plugged into port one to see if it gets an IP with the thought that maybe the console is freezing but it isn't getting an IP. And before you think it, yes I did remove the CF card.

Have removed the encryption card in case that was causing an issue but with no joy

So am now not sure what to do next?

Do I have a broken box or do I just need to find a way to flash the bios? I did note at the bios screen I have a date of 04/26/2010 which seems different from the date previously mentioned with bios flashes.

Thanks again
Luke

stephenw10

It's an odd place in the boot to stop. It's well after the loader variables are set, which is where it would break if you had the wrong baud rate configured. It's before it mounts the root filesystem, which is where it stops writing to all consoles so is thas last thing you see if you have the VGA console set as primary.
Does it still boot the WG OS correctly? Or, say, the OpenWRT x86 image if you don't have the original OS?

Steve

shawl01

@stephenw10 Haha, I did power it up before I started and from what I could tell it booted normally. However in the messing about between writing images to CF cards I have overwritten the CF card that came in the unit so now can't check again :-(

Thanks
Luke

shawl01

@stephenw10 I down loaded openwrt-18.06.4-x86-generic-combined-ext4.img and the unit boots with it but the serial port settings must be different as it comes up with garbage while booting looking around it seems to be 115200/8/1/None which is what I have set.

Thanks
Luke

stephenw10

Hmm, I thought that was the default now in OpenWRT too. Try 9600 though.

Maybe you have a bad serial cable? Trying to use the extended serial lines and failing?

Steve

shawl01

@stephenw10 Tried 9600 - no joy different garbage but still garbage. I am starting to wonder about the serial cable too but I need to look and see if I have any others with the rj45 end on them.

Thanks
Luke

stephenw10

With any half recent serial terminal you only need three connections. More than that might just break stuff if it's not wired correctly. Certainly to connect to pfSense you only need 3 pins connected.
Some older stuff like the X-e bios and FreeDOS required more.

Steve

shawl01

@stephenw10 Have tried three different cables now and all with the same results, lost

Luke

stephenw10

If you can find one you might try an old NanoBSD serial image directly on the CF card. There are still some mirrors out there hosting them even though they shouldn't be.

Steve