Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    Brand New sg-3100, first run, and don't work at all.

    Official Netgate® Hardware
    4
    4
    800
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • J
      Jorge.riquelme.p
      last edited by

      Hi, i bought a SG-3100 and just did not start. I connected from serial port and its look like an eternal booting loop. please help! (complete noobie user)

      Marvell>> boot
reading ubldr.bin
228664 bytes read in 10 ms (21.8 MiB/s)
## Starting application at 0x00200000 ...
Consoles: U-Boot console
Compatible U-Boot API signature found @0x7f4dc280

FreeBSD/armv6 U-Boot loader, Revision 1.2
(Wed Nov 21 09:38:18 EST 2018 root@buildbot2.nyi.netgate.com)

DRAM: 2048MB
Number of U-Boot devices: 4
U-Boot env: loaderdev not set, will probe all devices.
Found U-Boot device: disk
  Probing all disk devices...
  Checking unit=0 slice=<auto> partition=<auto>...disk0: read failed, error=1

  Checking unit=1 slice=<auto> partition=<auto>...disk1: read failed, error=1

  Checking unit=2 slice=<auto> partition=<auto>... good.
Booting from disk2s2a:
Loading /boot/defaults/loader.conf
console comconsole is invalid!
no valid consoles!
Available consoles:
    uboot
/boot/kernel/kernel data=0x11793d8+0x76c28 syms=[0x4+0x97d50+0x4+0xd84fb]
/
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
/boot/dtb/armada-385-80300-0148-G00-X100.dtb size=0x5307
Loaded DTB from file 'armada-385-80300-0148-G00-X100.dtb'.
Kernel entry at 0x400100...
Kernel args: (null)
Copyright (c) 1992-2018 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.2-RELEASE-p10 #12 10fea60fdde(factory-RELENG_2_4_4): Thu May 16 06:02:25 EDT 2019
    root@buildbot1-nyi.netgate.com:/build/factory-crossbuild-244/obj/armv6/tDULKC6G/arm.armv6/build/factory-crossbuild-244/pfSense/tmp/FreeBSD-src/sys/pfSense-SG-3100 arm
FreeBSD clang version 6.0.0 (tags/RELEASE_600/final 326565) (based on LLVM 6.0.0)
CPU: ARM Cortex-A9 r4p1 (ECO: 0x00000000)
CPU Features:
  Multiprocessing, Thumb2, Security, VMSAv7, Coherent Walk
Optional instructions:
  UMULL, SMULL, SIMD(ext)
LoUU:2 LoC:2 LoUIS:2
Cache level 1:
 32KB/32B 4-way data cache WB Read-Alloc Write-Alloc
 32KB/32B 4-way instruction cache Read-Alloc
real memory  = 2147479552 (2047 MB)
avail memory = 2082213888 (1985 MB)
SOC: Marvell 88F6820, TClock 250MHz, Frequency 1600MHz
  Instruction cache prefetch enabled, data cache prefetch disabled
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
random: entropy device external interface
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xc01337e4, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xc0133894, 0) error 1
wlan: mac acl policy registered
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xc0133944, 0) error 1
iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_bss_fw, 0xc013d120, 0) error 1
iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_ibss_fw, 0xc013d1d0, 0) error 1
iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_monitor_fw, 0xc013d280, 0) error 1
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
simplebus1: <Flattened device tree simple bus> on simplebus0
l2cache0: <PL310 L2 cache controller> mem 0x8000-0x8fff on simplebus1
l2cache0: cannot allocate IRQ, not using interrupt
l2cache0: Part number: 0x3, release: 0x9
l2cache0: L2 Cache enabled: 1024KB/32B 16 ways
gic0: <ARM Generic Interrupt Controller> mem 0xd000-0xdfff,0xc100-0xc1ff on simplebus1
gic0: pn 0x390, arch 0x1, rev 0x2, implementer 0x43b irqs 192
mpic0: <Marvell Integrated Interrupt Controller> mem 0x20a00-0x20ccf,0x21870-0x21b6f irq 19 on simplebus1
mp_tmr0: <ARM MPCore Timers> mem 0xc200-0xc21f irq 3 on simplebus1
Timecounter "MPCore" frequency 800000000 Hz quality 800
mp_tmr1: <ARM MPCore Timers> mem 0xc600-0xc61f irq 4 on simplebus1
Event timer "MPCore" frequency 800000000 Hz quality 1000
cesa0: <Marvell Cryptographic Engine and Security Accelerator> mem 0x90000-0x90fff,0x9d000-0x9dfff irq 1 on simplebus1
cesa1: <Marvell Cryptographic Engine and Security Accelerator> mem 0x92000-0x92fff,0x9f000-0x9ffff irq 2 on simplebus1
spi0: <Marvell SPI controller> mem 0x10600-0x1064f irq 5 on simplebus1
twsi0: <Marvell Integrated I2C Bus Controller> mem 0x11000-0x1101f irq 7 on simplebus1
iicbus0: <OFW I2C bus> on twsi0
iic0: <I2C generic I/O> on iicbus0
gpio0: <NXP PCA9552 LED driver> at addr 0xc0 on iicbus0
device_attach: gpio0 attach returned 6
gpio0: <ISSI IS31FL3199 9 channel light effect LED driver> at addr 0xce on iicbus0
gpiobus0: <OFW GPIO bus> on gpio0
gpioc0: <GPIO controller> on gpio0
gpio1: <NXP PCA9552 LED driver> at addr 0xc0 on iicbus0
device_attach: gpio1 attach returned 6
uart0: console (-1,n,8,1)le> mem 0x12000-0x120ff irq 9 on simplebus1
uart1: <16550 or compatible> mem 0x12100-0x121ff irq 10 on simplebus1
wdt0: <Marvell Watchdog Timer> mem 0x20300-0x20333,0x20704-0x20707,0x18260-0x18263 on simplebus1
pmsu0: <Power Management Service Unit> mem 0x22000-0x22fff on simplebus1
mvneta0: <NETA controller> mem 0x30000-0x33fff irq 26 on simplebus1
mvneta0: version is 10
mvneta0: Ethernet address: 00:08:a2:0f:98:c9
miibus0: <MII bus> on mvneta0
ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
ukphy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
mvneta1: <NETA controller> mem 0x34000-0x37fff irq 27 on simplebus1
mvneta1: version is 10
mvneta1: Ethernet address: 00:08:a2:0f:98:ca
mdio0: <MDIO> on mvneta1
e6000sw0: <Marvell 88E6141> on mdio0
e6000sw0: single-chip addressing mode
miibus1: <MII bus> on e6000sw0
e1000phy0: <Marvell 88E1000 Gigabit PHY> PHY 17 on miibus1
e1000phy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus2: <MII bus> on e6000sw0
e1000phy1: <Marvell 88E1000 Gigabit PHY> PHY 18 on miibus2
e1000phy1:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus3: <MII bus> on e6000sw0
e1000phy2: <Marvell 88E1000 Gigabit PHY> PHY 19 on miibus3
e1000phy2:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus4: <MII bus> on e6000sw0
e1000phy3: <Marvell 88E1000 Gigabit PHY> PHY 20 on miibus4
e1000phy3:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: switch is ready.
etherswitch0: <Switch controller> on e6000sw0
ehci0: <Marvell Integrated USB 2.0 controller> mem 0x58000-0x584ff irq 28 on simplebus1
usbus0: EHCI version 1.0
usbus0 on ehci0
mvneta2: <NETA controller> mem 0x70000-0x73fff irq 29 on simplebus1
mvneta2: version is 10
mvneta2: Ethernet address: 00:08:a2:0f:98:cb
miibus5: <MII bus> on mvneta2
ukphy1: <Generic IEEE 802.3u media interface> PHY 0 on miibus5
ukphy1:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
rtc0: <Marvell Integrated RTC> mem 0xa3800-0xa381f,0x184a0-0x184ab irq 30 on simplebus1
rtc0: registered as a time-of-day clock, resolution 1.000000s
ahci0: <Marvell AHCI Controller> mem 0xa8000-0xa9fff irq 31 on simplebus1
ahci0: AHCI v1.00 with 2 6Gbps ports, Port Multiplier supported with FBS
ahci0: quirks=0x200010<2CH,MRVL_SR_DEL>
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
armada_thermal0: <Armada380 Thermal Control> mem 0xe4078-0xe407b,0xe4074-0xe4077 on simplebus1
sdhci_fdt0: <ARMADA38X SDHCI controller> mem 0xd8000-0xd8fff,0xdc000-0xdc0ff,0x18454-0x18457 irq 34 on simplebus1
sdhci_fdt0: 1 slot(s) allocated
xhci0: <Marvell Integrated USB 3.0 controller> mem 0xf8000-0xfbfff,0xfc000-0xfffff irq 36 on simplebus1
xhci0: 32 bytes context size, 32-bit DMA
usbus1 on xhci0
pcib_ctrl0: <Marvell Integrated PCIe Bus Controller> on simplebus0
pcib0: <Marvell Integrated PCI/PCI-E Controller> on pcib_ctrl0
pci0: <PCI bus> on pcib0
pcib1: <Marvell Integrated PCI/PCI-E Controller> on pcib_ctrl0
pci1: <PCI bus> on pcib1
pcib2: <Marvell Integrated PCI/PCI-E Controller> on pcib_ctrl0
pci2: <PCI bus> on pcib2
pcib3: <Marvell Integrated PCI/PCI-E Controller> on pcib_ctrl0
pci3: <PCI bus> on pcib3
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
cpu1: <Open Firmware CPU> on cpulist0
cryptosoft0: <software crypto>
Timecounters tick every 1.000 msec
mvneta1: link state changed to UP
spibus0: <OFW SPI bus> on spi0
mx25l0: <M25Pxx Flash Family> at cs 0 mode 0 on spibus0
mx25l0: device type w25q32jv, size 4096K in 64 sectors of 64K, erase size 4K
e6000sw0port1: link state changed to DOWN
e6000sw0port2: link state changed to DOWN
e6000sw0port3: link state changed to DOWN
e6000sw0port4: link state changed to DOWN
usbus0: 480Mbps High Speed USB v2.0
usbus1: 5.0Gbps Super Speed USB v3.0
ugen0.1: <Marvell EHCI root HUB> at usbus0
uhub0: <Marvell EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen1.1: <Marvell XHCI root HUB> at usbus1
uhub1: <Marvell XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus1
uhub1: 2 ports with 2 removable, self powered
mmc0: <MMC/SD bus> on sdhci_fdt0
mmcsd0: 8GB <MMCHC M32508 0.1 SN 00888DD7 MFG 10/2018 by 112 0x0000> at mmc0 50.0MHz/8bit/65535-block
mmcsd0boot0: 4MB partion 1 at mmcsd0
mmcsd0boot1: 4MB partion 2 at mmcsd0
mmcsd0rpmb: 4MB partion 3 at mmcsd0
uhub0: 1 port with 1 removable, self powered
Release APs
Trying to mount root from ufs:/dev/ufsid/5cdd38aef2899872 [rw,noatime]...
WARNING: /build/factory-crossbuild-244/work/armv6/pfSense-rogue-1 was not properly dismounted
Configuring crash dumps...
dumpon: /dev/label/swap*: No such file or directory
Unable to specify /dev/label/swap* as a dump device.
No suitable dump device was found.
** SU+J Recovering /dev/ufsid/5cdd38aef2899872
** Reading 7503872 byte journal from inode 4.
** Building recovery table.
** Resolving unreferenced inode list.
** Processing journal entries.
** 24 journal records in 2560 bytes for 30.00% utilization
** Freed 0 inodes (0 dirs) 0 blocks, and 2 frags.

***** FILE SYSTEM MARKED CLEAN *****
Filesystems are clean, continuing...
Mounting filesystems...
random: unblocking device.

        __
 _ __  / _|___  ___ _ __  ___  ___
| '_ \| |_/ __|/ _ \ '_ \/ __|/ _ \
| |_) |  _\__ \  __/ | | \__ \  __/
| .__/|_| |___/\___|_| |_|___/\___|
|_|


Welcome to pfSense 2.4.4-RELEASE (Patch 3)...

...ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib /usr/local/lib/ipsec /usr/local/lib/perl5/5.26/mach/CORE
Soft Float compatibility ldconfig path:
done.
External config loader 1.0 is now starting... mmcsd0s1 mmcsd0s2 mmcsd0s2a
Launching the init system...mode = 0100666, inum = 30742, fs = /build/factory-crossbuild-244/work/armv6/pfSense-rogue-1
panic: ffs_valloc: dup alloc
cpuid = 1
Uptime: 15s
Automatic reboot in 15 seconds - press a key on the console to abort
--> Press a key on the console to reboot,
--> or switch off the system now.
      1 Reply Last reply Reply Quote 0
      • kiokomanK
        kiokoman LAYER 8
        last edited by kiokoman

        @Jorge-riquelme-p said in Brand New sg-3100, first run, and don't work at all.:

        panic: ffs_valloc: dup alloc

        it marks the disk clean when in fact it is not clean. To resolve this problem, you must bring the machine up single user and run a full fsck on it using fsck . This will find the hidden problem and correct it.

        That can happen in rare cases if, say, the power is removed without a proper shutdown.

        /sbin/fsck -y /

        a few times (4 or 5)

        follow this direction
        https://forum.netgate.com/post/745773

        ̿' ̿'\̵͇̿̿\з=(◕_◕)=ε/̵͇̿̿/'̿'̿ ̿
        Please do not use chat/PM to ask for help
        we must focus on silencing this @guest character. we must make up lies and alter the copyrights !
        Don't forget to Upvote with the 👍 button for any post you find to be helpful.

        1 Reply Last reply Reply Quote 0
        • A
          amarcino
          last edited by

          I went through this last week. It is not too hard. You have to have your console session ready before you power on the device, because you have to stop the Marvell boot loader when prompted and I think you only have a few seconds to do it. It comes up quick and if you are not paying close attention you will miss it you then have to shut it down and try again.

          1 Reply Last reply Reply Quote 0
          • stephenw10S
            stephenw10 Netgate Administrator
            last edited by

            Yes, the directions in that linked post should correct that for you but it you have any problems running that please open a ticket with us: https://go.netgate.com/

            Steve

            1 Reply Last reply Reply Quote 0
            • First post
              Last post
            Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.