Install on NETASQ U30 S ?

xobix · Feb 8, 2020, 6:00 PM

Hi,

I try to install pfsense on old Netasq U 30S.

I'm note able to boot on my USB key. I make it with Rufus.

When I select my drive to boot, router return error message :

NETASQ USB Disk Fail
Reboot and Select a proper Boot device

Somebody have an idea ?

stephenw10 · Feb 9, 2020, 12:55 PM

What hardware is in that device? Exactly what image are you using?

Try using Etcher to write the image instead.

Steve

xobix · Feb 9, 2020, 4:02 PM

>uname -p
i386

So I put "pfSense-CE-2.3.5-RELEASE-2g-i386-nanobsd-vga.img" on my USB stick with balena Etcher.

The result is Always the same

xobix · Feb 9, 2020, 6:46 PM

I try to boot on my USB stick on old optiplex computer and it works.

Is there a securry to avoid other OS installation?

stephenw10 · Feb 9, 2020, 9:08 PM

There maybe some sort of boot lock but I've not seen that before on a Netasq, though I've not seen many.

That image probably appears as a USB-HDD if you have a boot option for that.

However that version is obsolete, unsupported, and that hardware is too if it's 32bit only. Do you know exactly what it is? What CPU? How much RAM etc?

Steve

xobix · Feb 10, 2020, 7:49 AM

CPU : VIA Nano U3400@800Mhz RAM : 1G
CPU seems to be 64 bit. I will try again with the last img (pfSense-CE-memstick-2.4.4-RELEASE-p3-amd64.img)

xobix · Feb 10, 2020, 7:52 AM

And is the same issue :(

stephenw10 · Feb 10, 2020, 12:01 PM

Hmm, well it's not going to be fast but it is 64bit so should run 2.4.4.

A long while back when I installed a U250S I could not make it boot from USB either and instead I installed it in a different machine and then moved the HD back into it. Since I did have console access I was able to re-assign the interfaces from there. They were dual igb NICs on that.
Then came fun with the on-board switch, which that might also have.
I was able to access it via the second com port at 19600bps just for reference.

Edit: I see it's shown as having ports:

5 (1+2x2 ports switch)

So it may be configured as two interfaces by default. You may to need to do anything with the switch, though you might want to anyway.

Steve

xobix · Feb 10, 2020, 1:52 PM

login-to-view

as you said I installed it on other computer and moved back the HDD in the NETASQ

On display I see 2 interfaces instead of 3. Is it normal ? (I 'm a verry beginner on PF sense )

stephenw10 · Feb 10, 2020, 2:29 PM

Yes, WAN and LAN is the default if it finds usable interfaces.

Try using menu option 8 to drop to the command line and running ifconfig -vma to see all available interfaces and their capabilities.

If you connect the WAN port to something running dhcp does it pull a lease on the WAN interface?

Steve

xobix · Feb 10, 2020, 4:26 PM

>ifconfig -vma

em0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=2098<VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC>
        capabilities=15399b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,NETMAP>
        ether 00:0d:b4:0d:f9:02
        hwaddr 00:0d:b4:0d:f9:02
        inet6 fe80::20d:b4ff:fe0d:f902%em0 prefixlen 64 scopeid 0x1
        inet 192.168.1.1 netmask 0xffffff00 broadcast 192.168.1.255
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
        media: Ethernet autoselect (1000baseT <full-duplex>)
        status: active
        supported media:
                media autoselect
                media 1000baseT
                media 1000baseT mediaopt full-duplex
                media 100baseTX mediaopt full-duplex
                media 100baseTX
                media 10baseT/UTP mediaopt full-duplex
                media 10baseT/UTP
em1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=2098<VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC>
        capabilities=15399b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,NETMAP>
        ether 00:0d:b4:0d:f9:03
        hwaddr 00:0d:b4:0d:f9:03
        inet6 fe80::20d:b4ff:fe0d:f903%em1 prefixlen 64 scopeid 0x2
        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>
        media: Ethernet autoselect
        status: no carrier
        supported media:
                media autoselect
                media 1000baseT
                media 1000baseT mediaopt full-duplex
                media 100baseTX mediaopt full-duplex
                media 100baseTX
                media 10baseT/UTP mediaopt full-duplex
                media 10baseT/UTP
enc0: flags=0<> metric 0 mtu 1536
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
        groups: enc
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
        options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
        capabilities=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
        inet6 ::1 prefixlen 128
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4
        inet 127.0.0.1 netmask 0xff000000
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
        groups: lo
pflog0: flags=100<PROMISC> metric 0 mtu 33184
        groups: pflog
pfsync0: flags=0<> metric 0 mtu 1500
        groups: pfsync
        syncpeer: 0.0.0.0 maxupd: 128 defer: off

stephenw10 · Feb 10, 2020, 5:46 PM

Ok, so no other interfaces. Or none detected and with drivers attached at least.

One of the ports is up and that presumably how you're connecting. Which external port are you connected to?

Do you have links on the other ports? The switch ports presumably.

If you have a serial console connected now you could post the boot logs so we can see what else might be in there.

The output of pciconf -lv might also be interesting.

Steve

xobix · Feb 10, 2020, 6:45 PM

I m connected on port 1 of the switch via SSH. It's the LAN em0.

I think i have not link on other ports (no LED flashing when i plug a cable).

I havn't got serial adptator :(

the result of the command :

>piconf -lv
hostb0@pci0:0:0:0:      class=0x060000 card=0x04101106 chip=0x04101106 rev=0x80 hdr=0x00
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VX900 Host Bridge: Host Control'
    class      = bridge
    subclass   = HOST-PCI
hostb1@pci0:0:0:1:      class=0x060000 card=0x14101106 chip=0x14101106 rev=0x00 hdr=0x00
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VX900 Error Reporting'
    class      = bridge
    subclass   = HOST-PCI
hostb2@pci0:0:0:2:      class=0x060000 card=0x24101106 chip=0x24101106 rev=0x00 hdr=0x00
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VX900 CPU Bus Controller'
    class      = bridge
    subclass   = HOST-PCI
hostb3@pci0:0:0:3:      class=0x060000 card=0x34101106 chip=0x34101106 rev=0x00 hdr=0x00
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VX900 DRAM Bus Control'
    class      = bridge
    subclass   = HOST-PCI
hostb4@pci0:0:0:4:      class=0x060000 card=0x44101106 chip=0x44101106 rev=0x00 hdr=0x00
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VX900 Power Management and Chip Testing Control'
    class      = bridge
    subclass   = HOST-PCI
hostb5@pci0:0:0:5:      class=0x060000 card=0x54101106 chip=0x54101106 rev=0x00 hdr=0x00
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VX900 APIC and Central Traffic Control'
    class      = bridge
    subclass   = HOST-PCI
hostb6@pci0:0:0:6:      class=0x060000 card=0x64101106 chip=0x64101106 rev=0x00 hdr=0x00
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VX900 Scratch Registers'
    class      = bridge
    subclass   = HOST-PCI
hostb7@pci0:0:0:7:      class=0x060000 card=0x74101106 chip=0x74101106 rev=0x00 hdr=0x00
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VX900 North-South Module Interface Control'
    class      = bridge
    subclass   = HOST-PCI
vgapci0@pci0:0:1:0:     class=0x030000 card=0x71221106 chip=0x71221106 rev=0x00 hdr=0x00
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VX900 Graphics [Chrome9 HD]'
    class      = display
    subclass   = VGA
pcib1@pci0:0:3:0:       class=0x060400 card=0xa4101106 chip=0xa4101106 rev=0x00 hdr=0x01
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VX900 PCI Express Root Port 0'
    class      = bridge
    subclass   = PCI-PCI
pcib2@pci0:0:3:1:       class=0x060400 card=0xb4101106 chip=0xb4101106 rev=0x00 hdr=0x01
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VX900 PCI Express Root Port 1'
    class      = bridge
    subclass   = PCI-PCI
pcib3@pci0:0:3:2:       class=0x060400 card=0xc4101106 chip=0xc4101106 rev=0x00 hdr=0x01
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VX900 PCI Express Root Port 2'
    class      = bridge
    subclass   = PCI-PCI
pcib4@pci0:0:3:3:       class=0x060400 card=0xd4101106 chip=0xd4101106 rev=0x00 hdr=0x01
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VX900 PCI Express Root Port 3'
    class      = bridge
    subclass   = PCI-PCI
hostb8@pci0:0:3:4:      class=0x060000 card=0x00000000 chip=0xe4101106 rev=0x00 hdr=0x00
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VX900 PCI Express Physical Layer Electrical Sub-block'
    class      = bridge
    subclass   = HOST-PCI
none0@pci0:0:11:0:      class=0x028000 card=0xa4091106 chip=0xa4091106 rev=0x10 hdr=0x00
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VX855/VX875 USB Device Controller'
    class      = network
sdhci_pci0@pci0:0:12:0: class=0x080501 card=0x95d01106 chip=0x95d01106 rev=0x10 hdr=0x00
    vendor     = 'VIA Technologies, Inc.'
    device     = 'SDIO Host Controller'
    class      = base peripheral
    subclass   = SD host controller
atapci0@pci0:0:15:0:    class=0x01018f card=0x90011106 chip=0x90011106 rev=0x00 hdr=0x00
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VX900 Serial ATA Controller'
    class      = mass storage
    subclass   = ATA
uhci0@pci0:0:16:0:      class=0x0c0300 card=0x30381106 chip=0x30381106 rev=0xa0 hdr=0x00
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VT82xx/62xx UHCI USB 1.1 Controller'
    class      = serial bus
    subclass   = USB
uhci1@pci0:0:16:1:      class=0x0c0300 card=0x30381106 chip=0x30381106 rev=0xa0 hdr=0x00
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VT82xx/62xx UHCI USB 1.1 Controller'
    class      = serial bus
    subclass   = USB
uhci2@pci0:0:16:2:      class=0x0c0300 card=0x30381106 chip=0x30381106 rev=0xa0 hdr=0x00
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VT82xx/62xx UHCI USB 1.1 Controller'
    class      = serial bus
    subclass   = USB
uhci3@pci0:0:16:3:      class=0x0c0300 card=0x30381106 chip=0x30381106 rev=0xa0 hdr=0x00
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VT82xx/62xx UHCI USB 1.1 Controller'
    class      = serial bus
    subclass   = USB
ehci0@pci0:0:16:4:      class=0x0c0320 card=0x31041106 chip=0x31041106 rev=0x90 hdr=0x00
    vendor     = 'VIA Technologies, Inc.'
    device     = 'USB 2.0'
    class      = serial bus
    subclass   = USB
isab0@pci0:0:17:0:      class=0x060100 card=0x84101106 chip=0x84101106 rev=0x00 hdr=0x00
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VX900 Bus Control and Power Management'
    class      = bridge
    subclass   = PCI-ISA
hostb9@pci0:0:17:7:     class=0x060000 card=0xa3531106 chip=0xa3531106 rev=0x00 hdr=0x00
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VX8xx South-North Module Interface Control'
    class      = bridge
    subclass   = HOST-PCI
pcib5@pci0:0:19:0:      class=0x060401 card=0xb3531106 chip=0xb3531106 rev=0x00 hdr=0x01
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VX855/VX875/VX900 PCI to PCI Bridge'
    class      = bridge
    subclass   = PCI-PCI
em0@pci0:3:0:0: class=0x020000 card=0x00008086 chip=0x10d38086 rev=0x00 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82574L Gigabit Network Connection'
    class      = network
    subclass   = ethernet
em1@pci0:4:0:0: class=0x020000 card=0x00008086 chip=0x10d38086 rev=0x00 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82574L Gigabit Network Connection'
    class      = network
    subclass   = ethernet

stephenw10 · Feb 10, 2020, 7:51 PM

Ok only the USB controller not recognised:

none0@pci0:0:11:0:      class=0x028000 card=0xa4091106 chip=0xa4091106 rev=0x10 hdr=0x00
    vendor     = 'VIA Technologies, Inc.'
    device     = 'VX855/VX875 USB Device Controller'
    class      = network

Probably not important, I also see that.

So you are connected to port1 and the 4 stacked ports labelled 2 and 3 show no link, correct?

Try this. At the command line run:
cu -l /dev/cuau1 -s 19600
Hit return see if you can see the switch interface.
To escape the cu session hit return then type ~~.

Steve

xobix · Feb 10, 2020, 8:18 PM

@stephenw10 said in Install on NETASQ U30 S ?:

So you are connected to port1 and the 4 stacked ports labelled 2 and 3 show no link, correct?

true

>cu -l /dev/cuau1 -s 19600
Connected

I can't type anything after, I have no prompt

xobix · Feb 10, 2020, 9:03 PM

can it help you ?

> # dmesg
Copyright (c) 2013-2018 The HardenedBSD Project.
Copyright (c) 1992-2018 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.2-RELEASE-p16-HBSD  fc65add89c3(stable/20.1) i386
FreeBSD clang version 6.0.0 (tags/RELEASE_600/final 326565) (based on LLVM 6.0.0)
VT(vga): resolution 640x480
HardenedBSD: initialize and check features (__HardenedBSD_version 1100056 __FreeBSD_version 1102000).
CPU: VIA Nano U3400@800MHz (800.05-MHz 686-class CPU)
  Origin="CentaurHauls"  Id=0x6fa  Family=0x6  Model=0xf  Stepping=10
  Features=0xafc9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,PBE>
  Features2=0x8863a9<SSE3,MON,VMX,EST,TM2,SSSE3,CX16,xTPR,SSE4.1,POPCNT>
  AMD Features=0x20100800<SYSCALL,NX,LM>
  AMD Features2=0x1<LAHF>
  VIA Padlock Features=0x1ec33dcc<RNG,AES,AES-CTR,SHA1,SHA256,RSA>
  VT-x: HLT,PAUSE
  TSC: P-state invariant
real memory  = 1073741824 (1024 MB)
avail memory = 1012875264 (965 MB)
Event timer "LAPIC" quality 100
ACPI APIC Table: <031412 APIC1628>
ioapic0 <Version 0.3> irqs 0-23 on motherboard
ioapic1 <Version 0.3> irqs 24-47 on motherboard
Timecounter "TSC" frequency 800047908 Hz quality 1000
random: entropy device external interface
wlan: mac acl policy registered
kbd1 at kbdmux0
000.000024 [4213] netmap_init               netmap: loaded module
module_register_init: MOD_LOAD (vesa, 0xc116f230, 0) error 19
random: registering fast source VIA Nehemiah Padlock RNG
random: fast provider: "VIA Nehemiah Padlock RNG"
nexus0
vtvga0: <VT VGA driver> on motherboard
cryptosoft0: <software crypto> on motherboard
acpi0: <031412 XSDT1628> on motherboard
acpi0: Power Button (fixed)
cpu0: <ACPI CPU> on acpi0
attimer0: <AT timer> port 0x40-0x43 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <AT realtime clock> port 0x70-0x71 on acpi0
atrtc0: registered as a time-of-day clock, resolution 1.000000s
Event timer "RTC" frequency 32768 Hz quality 0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff irq 0,8 on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Event timer "HPET" frequency 14318180 Hz quality 450
Event timer "HPET1" frequency 14318180 Hz quality 450
Event timer "HPET2" frequency 14318180 Hz quality 450
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
vgapci0: <VGA-compatible display> mem 0xfd000000-0xfdffffff,0xfc000000-0xfcffffff,0xfb800000-0xfbffffff irq 40 at device 1.0 on pci0
vgapci0: Boot video device
pcib1: <ACPI PCI-PCI bridge> irq 27 at device 3.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> irq 31 at device 3.1 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> irq 35 at device 3.2 on pci0
pcib3: [GIANT-LOCKED]
pci3: <ACPI PCI bus> on pcib3
em0: <Intel(R) PRO/1000 Network Connection 7.6.1-k> port 0xdc00-0xdc1f mem 0xfeae0000-0xfeafffff,0xfeadc000-0xfeadffff irq 32 at device 0.0 on pci3
em0: Using MSIX interrupts with 3 vectors
em0: Ethernet address: 00:0d:b4:0d:f9:02
em0: netmap queues/slots: TX 1/1024, RX 1/1024
pcib4: <ACPI PCI-PCI bridge> irq 39 at device 3.3 on pci0
pci4: <ACPI PCI bus> on pcib4
em1: <Intel(R) PRO/1000 Network Connection 7.6.1-k> port 0xec00-0xec1f mem 0xfebe0000-0xfebfffff,0xfebdc000-0xfebdffff irq 36 at device 0.0 on pci4
em1: Using MSIX interrupts with 3 vectors
em1: Ethernet address: 00:0d:b4:0d:f9:03
em1: netmap queues/slots: TX 1/1024, RX 1/1024
pci0: <network> at device 11.0 (no driver attached)
sdhci_pci0: <Generic SD HCI> port 0xcc00-0xcc07 mem 0xfe9ef400-0xfe9ef4ff irq 22 at device 12.0 on pci0
sdhci_pci0: 1 slot(s) allocated
atapci0: <VIA VX900 SATA300 controller> port 0xc880-0xc887,0xc800-0xc803,0xc480-0xc487,0xc400-0xc403,0xc080-0xc08f irq 21 at device 15.0 on pci0
ata2: <ATA channel> at channel 0 on atapci0
ata3: <ATA channel> at channel 1 on atapci0
uhci0: <VIA 83C572 USB controller> port 0xc000-0xc01f irq 20 at device 16.0 on pci0
uhci0: LegSup = 0xa000
usbus0 on uhci0
uhci1: <VIA 83C572 USB controller> port 0xbc00-0xbc1f irq 22 at device 16.1 on pci0
uhci1: LegSup = 0xa000
usbus1 on uhci1
uhci2: <VIA 83C572 USB controller> port 0xb880-0xb89f irq 21 at device 16.2 on pci0
uhci2: LegSup = 0xa000
usbus2 on uhci2
uhci3: <VIA 83C572 USB controller> port 0xb800-0xb81f irq 23 at device 16.3 on pci0
uhci3: LegSup = 0xa000
usbus3 on uhci3
ehci0: <VIA VT6202 USB 2.0 controller> mem 0xfe9ef000-0xfe9ef0ff irq 23 at device 16.4 on pci0
usbus4: EHCI version 1.0
usbus4 on ehci0
isab0: <PCI-ISA bridge> at device 17.0 on pci0
isa0: <ISA bus> on isab0
pcib5: <ACPI PCI-PCI bridge> at device 19.0 on pci0
pci5: <ACPI PCI bus> on pcib5
acpi_button0: <Sleep Button> on acpi0
acpi_button1: <Power Button> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_tz1: <Thermal Zone> on acpi0
acpi_acad0: <AC Adapter> on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
pmtimer0 on isa0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ata0: <ATA channel> at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata1: <ATA channel> at port 0x170-0x177,0x376 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
ppc0: parallel port not found.
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor CentaurHauls, msr 84708470800084b
device_attach: est0 attach returned 6
Timecounters tick every 1.000 msec
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
ugen0.1: <VIA UHCI root HUB> at usbus0
uhub0: <VIA UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <VIA UHCI root HUB> at usbus1
uhub1: <VIA UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <VIA UHCI root HUB> at usbus2
uhub2: <VIA UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 480Mbps High Speed USB v2.0
ugen3.1: <VIA UHCI root HUB> at usbus3
uhub3: <VIA UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <VIA EHCI root HUB> at usbus4
uhub4: <VIA EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
ada0 at ata2 bus 0 scbus0 target 1 lun 0
ada0: <TOSHIBA MK1246GSX LB211A> ATA8-ACS SATA 1.x device
ada0: Serial Number 97LNF2E8S
ada0: 150.000MB/s transfers (SATA 1.x, UDMA5, PIO 8192bytes)
ada0: 114473MB (234441648 512 byte sectors)
uhub4: 8 ports with 8 removable, self powered
ugen1.2: <vendor 0x046d G15 Keyboard Hub> at usbus1
uhub5 on uhub1
uhub5: <vendor 0x046d G15 Keyboard Hub, class 9/0, rev 1.10/0.20, addr 2> on usbus1
uhub5: 4 ports with 2 removable, bus powered
random: unblocking device.
ugen1.3: <vendor 0x046d G15 Gaming Keyboard> at usbus1
ukbd0 on uhub5
ukbd0: <vendor 0x046d G15 Gaming Keyboard, class 0/0, rev 2.00/1.00, addr 3> on usbus1
kbd2 at ukbd0
ugen1.4: <vendor 0x046d G15 GamePanel LCD> at usbus1
hid_get_item: Number of items(991) truncated to 255
warning: total configured swap (1048576 pages) exceeds maximum recommended amount (496832 pages).
warning: increase kern.maxswzone or reduce amount of swap.
uhid0 on uhub5
uhid0: <vendor 0x046d G15 Gaming Keyboard, class 0/0, rev 2.00/1.00, addr 3> on usbus1
hid_get_item: Number of items(991) truncated to 255
uhid1 on uhub5
uhid1: <vendor 0x046d G15 GamePanel LCD, class 0/0, rev 2.00/0.20, addr 4> on usbus1
hid_get_item: Number of items(991) truncated to 255
hid_get_item: Number of items(991) truncated to 255
hid_get_item: Number of items(991) truncated to 255
aesni0: No AESNI support.
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
em0: link state changed to UP
em0: link state changed to DOWN
em0: link state changed to UP
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
em0: link state changed to DOWN
em0: link state changed to UP
ugen1.2: <vendor 0x046d G15 Keyboard Hub> at usbus1 (disconnected)
uhub5: at uhub1, port 1, addr 2 (disconnected)
ugen1.3: <vendor 0x046d G15 Gaming Keyboard> at usbus1 (disconnected)
ukbd0: at uhub5, port 1, addr 3 (disconnected)
ukbd0: detached
uhid0: at uhub5, port 1, addr 3 (disconnected)
uhid0: detached
ugen1.4: <vendor 0x046d G15 GamePanel LCD> at usbus1 (disconnected)
uhid1: at uhub5, port 4, addr 4 (disconnected)
uhid1: detached
uhub5: detached

xobix · Feb 10, 2020, 9:19 PM

It can be the cause?

pci0: <network> at device 11.0 (no driver attached)

stephenw10 · Feb 10, 2020, 10:29 PM

There is no driver that recognises it, that;s the device shown as none0 in the pciconf output.

Ok I typo'd the baud rate! Try: cu -l /dev/cuau1 -s 19200

If there's still nothing look in /dev to see if there are other serial ports.

Steve

xobix · Feb 10, 2020, 10:39 PM

@stephenw10 said in Install on NETASQ U30 S ?:

cu -l /dev/cuau1 -s 19200

same issue.
I tried cuau0 too

# ls /dev
acpi            ctty            hpet0           pass0           ttyu0.lock      ttyva
ada0            cuau0           io              pci             ttyu1           ttyvb
ada0s1          cuau0.init      kbd0            pf              ttyu1.init      ufs
ada0s1a         cuau0.lock      kbd1            pts             ttyu1.lock      ufssuspend
ada0s1b         cuau1           kbdmux0         random          ttyv0           ugen0.1
apm             cuau1.init      klog            reroot          ttyv1           ugen1.1
apmctl          cuau1.lock      kmem            sndstat         ttyv2           ugen2.1
atkbd0          devctl          led             speaker         ttyv3           ugen3.1
audit           devctl2         mdctl           stderr          ttyv4           ugen4.1
auditpipe       devstat         mem             stdin           ttyv5           urandom
bpf             fd              midistat        stdout          ttyv6           usb
bpf0            fido            netmap          sysmouse        ttyv7           usbctl
console         full            nfslock         ttyu0           ttyv8           xpt0
consolectl      geom.ctl        null            ttyu0.init      ttyv9           zero

stephenw10 · Feb 11, 2020, 8:52 AM

Hmm, it's at 9600 on the U70: https://forum.netgate.com/post/882959

Try: cu -l /dev/cuau1 -s 9600