IPhone Tethering to pfSense

stephenw10

Yeah you should see it in usbconfig and dmesg after connecting it. You won't see it as an interface in ifconfig until a driver attaches to it.

Steve

eiger3970

Ok, finally have the hypervisor working and passing the USB to the pfSense VM.
Not sure on the config for the pfSense VM to use a USB modem, so will try this link.

[2.4.4-RELEASE][admin@pfSense.localdomain]/boot: usbconfig
ugen1.1: <Intel UHCI root HUB> at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE (0mA)
ugen0.1: <Intel UHCI root HUB> at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE (0mA)
ugen3.1: <Intel UHCI root HUB> at usbus3, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE (0mA)
ugen2.1: <Intel UHCI root HUB> at usbus2, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE (0mA)
ugen4.1: <Intel EHCI root HUB> at usbus4, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA)
ugen0.2: <QEMU QEMU USB Tablet> at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON (100mA)
ugen4.2: <Apple Inc. iPhone> at usbus4, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON (500mA)
[2.4.4-RELEASE][admin@pfSense.localdomain]/boot: ifconfig
vtnet0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	options=c00b8<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,VLAN_HWTSO,LINKSTATE>
	ether 42:63:7c:e4:6c:e3
	hwaddr 42:63:7c:e4:6c:e3
	inet6 fe80::4063:7cff:fee4:6ce3%vtnet0 prefixlen 64 scopeid 0x1 
	inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255 
	nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>
	media: Ethernet 10Gbase-T <full-duplex>
	status: active
vtnet1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	options=c00b8<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,VLAN_HWTSO,LINKSTATE>
	ether a6:2d:d5:4f:6c:f3
	hwaddr a6:2d:d5:4f:6c:f3
	inet6 fe80::a42d:d5ff:fe4f:6cf3%vtnet1 prefixlen 64 scopeid 0x2 
	inet 192.168.1.170 netmask 0xffffff00 broadcast 192.168.1.255 
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	media: Ethernet 10Gbase-T <full-duplex>
	status: active
enc0: flags=0<> metric 0 mtu 1536
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	groups: enc 
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
	options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
	inet6 ::1 prefixlen 128 
	inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 
	inet 127.0.0.1 netmask 0xff000000 
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	groups: lo 
pflog0: flags=100<PROMISC> metric 0 mtu 33160
	groups: pflog 
pfsync0: flags=0<> metric 0 mtu 1500
	groups: pfsync 
	syncpeer: 224.0.0.240 maxupd: 128 defer: on
	syncok: 1

Post 6, point 5, pfSense shows:
pfSense > Interfaces > Assign.
My pfSense 2.4.4 > Interfaces > Assignments > has no option to add OPT2. What do I need to do to add the USB?

stephenw10

If the phone is detected and you see a ue0 interface you should just be able to assign it and set it as dhcp.

Also: https://github.com/pfsense/pfsense/commit/41e09c2264bcc8067c349213eab5c0dadfb5681f

eiger3970

pfSense 2.4.4 has the kernel module if_ipheth.ko:

[2.4.4-RELEASE][admin@pfSense.localdomain]/boot/modules: ls
bwi_v3_ucode.ko if_ipheth.ko    linker.hints

pfSense 2.4.4 /boot has the loader.conf file:

[2.4.4-RELEASE][admin@pfSense.localdomain]/boot: ls
beastie.4th        brand.4th          frames.4th         loader.efi         menu-commands.4th  userboot.so
boot               cdboot             gptboot            loader.help        menu.4th           version.4th
boot0              check-password.4th gptzfsboot         loader.rc          menu.rc            zfs
boot0sio           color.4th          isoboot            logo-beastie.4th   menusets.4th       zfsboot
boot1              defaults           kernel             logo-beastiebw.4th modules            zfsloader
boot1.efi          delay.4th          kernel.old         logo-fbsdbw.4th    pmbr
boot1.efifat       device.hints       loader             logo-orb.4th       pxeboot
boot2              dtb                loader.4th         logo-orbbw.4th     screen.4th
brand-fbsd.4th     entropy            loader.conf        logo-pfSensebw.4th shortcuts.4th
brand-pfSense.4th  firmware           loader.conf.origin mbr                support.4th

pfSense 2.4.4 has the loader.conf file edited:

kern.cam.boot_delay=10000
kern.ipc.nmbclusters="1000000"
kern.ipc.nmbjumbop="524288"
kern.ipc.nmbjumbo9="524288"
if_ipheth_load="YES"
autoboot_delay="3"
hw.usb.no_pf="1"

Not sure why I can't edit the pfSense GUI to add the USB modem now?
usbconfig shows ugen4.2, rather than ue0, but not sure why and if it's an issue?

eiger3970

Not sure what to do with the GitHub code?
Think I'll file a bug report.

eiger3970

I thought this Cellular Wireless guide might help.

However, unable to type in the pfSense 2.4.4-RELEASE-p2 > Interfaces > PPPs > PPP Configuration > Link Interface(s): /dev/ugen4.2

stephenw10

I'm pretty sure ipheth does not provide any interfaces you could use with PPP. It will appear as a USB Ethernet device when it's working.

You should put that loader line in loader.conf.local to avoid it being overwritten. Create that file since you don't have it yet.

Try running kldstat to see that the module is loaded.

Connect the phone then check the system log or dmesg to see what pfSense did.

What phone are you connecting? ipgeth appears to have specific support for iphones 1-5:
https://github.com/pfsense/FreeBSD-src/blob/RELENG_2_5/sys/dev/usb/net/if_ipheth.c#L136

Though it also tries to match any Apple device with the correct interface class.

Steve

akuma1x

I know we're trying to get an iPhone tethered to pfsense and get it working, but why don't you try this?

GL.iNet GL-AR750 Travel AC Router
https://www.amazon.com/GL-iNet-GL-AR750-300Mbps-pre-Installed-Included/dp/B07712LKJM

There are a few lower-spec'd models, since you don't need the wifi on this travel router box.

That would provide an ethernet interface, and still use the iPhone to grab the internet connection from your cellular provider. It works pretty well, if you've got a good signal.

Jeff

eiger3970

Thanks @stephenw10,
The kernel module is running:

[2.4.4-RELEASE][admin@pfSense.localdomain]/.ssh: kldstat
Id Refs Address            Size     Name
 1    8 0xffffffff80200000 2d9a7d0  kernel
 2    1 0xffffffff82f9c000 4318     if_ipheth.ko
 3    1 0xffffffff83019000 10a0     cpuctl.ko

dmesg shows pfSense has found the iPhone (18th line from the bottom):

[2.4.4-RELEASE][admin@pfSense.localdomain]/.ssh: dmesg:
Copyright (c) 1992-2018 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.2-RELEASE-p6 #3 518496b29ae(RELENG_2_4_4): Wed Dec 12 07:41:44 EST 2018
    root@buildbot2.nyi.netgate.com:/build/ce-crossbuild-244/obj/amd64/ZfGpH5cd/build/ce-crossbuild-244/pfSense/tmp/FreeBSD-src/sys/pfSense amd64
FreeBSD clang version 6.0.0 (tags/RELEASE_600/final 326565) (based on LLVM 6.0.0)
VT(vga): text 80x25
CPU: Common KVM processor (3092.92-MHz K8-class CPU)
  Origin="GenuineIntel"  Id=0xf61  Family=0xf  Model=0x6  Stepping=1
  Features=0x783fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE,SSE2>
  Features2=0x80202001<SSE3,CX16,x2APIC,HV>
  AMD Features=0x20100800<SYSCALL,NX,LM>
  AMD Features2=0x1<LAHF>
Hypervisor: Origin = "KVMKVMKVM"
real memory  = 1073741824 (1024 MB)
avail memory = 981479424 (936 MB)
Event timer "LAPIC" quality 100
ACPI APIC Table: <BOCHS  BXPCAPIC>
ioapic0 <Version 1.1> irqs 0-23 on motherboard
Timecounter "TSC-low" frequency 1546458305 Hz quality 800
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff80680430, 0) error 1
random: entropy device external interface
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff806804e0, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff80680590, 0) error 1
iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_bss_fw, 0xffffffff806a7460, 0) error 1
iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffffffff806a7510, 0) error 1
iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffffffff806a75c0, 0) error 1
wlan: mac acl policy registered
kbd1 at kbdmux0
netmap: loaded module
module_register_init: MOD_LOAD (vesa, 0xffffffff81209800, 0) error 19
nexus0
vtvga0: <VT VGA driver> on motherboard
cryptosoft0: <software crypto> on motherboard
padlock0: No ACE support.
acpi0: <BOCHS BXPCRSDT> on motherboard
acpi0: Power Button (fixed)
cpu0: <ACPI CPU> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x71,0x72-0x77 irq 8 on acpi0
atrtc0: registered as a time-of-day clock, resolution 1.000000s
Event timer "RTC" frequency 32768 Hz quality 0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 100000000 Hz quality 950
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x608-0x60b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
isab0: <PCI-ISA bridge> at device 1.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX3 WDMA2 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xe120-0xe12f at device 1.1 on pci0
ata0: <ATA channel> at channel 0 on atapci0
ata1: <ATA channel> at channel 1 on atapci0
uhci0: <Intel 82371SB (PIIX3) USB controller> port 0xe040-0xe05f irq 11 at device 1.2 on pci0
usbus0 on uhci0
pci0: <bridge> at device 1.3 (no driver attached)
vgapci0: <VGA-compatible display> mem 0xfa000000-0xfbffffff,0xfea90000-0xfea90fff at device 2.0 on pci0
vgapci0: Boot video device
virtio_pci0: <VirtIO PCI Balloon adapter> port 0xe060-0xe07f mem 0xfc000000-0xfc7fffff irq 11 at device 3.0 on pci0
vtballoon0: <VirtIO Balloon Adapter> on virtio_pci0
virtio_pci1: <VirtIO PCI Block adapter> port 0xe000-0xe03f mem 0xfea91000-0xfea91fff,0xfc800000-0xfcffffff irq 10 at device 10.0 on pci0
vtblk0: <VirtIO Block Adapter> on virtio_pci1
vtblk0: 8192MB (16777216 512 byte sectors)
virtio_pci2: <VirtIO PCI Network adapter> port 0xe080-0xe09f mem 0xfea92000-0xfea92fff,0xfd000000-0xfd7fffff irq 10 at device 18.0 on pci0
vtnet0: <VirtIO Networking Adapter> on virtio_pci2
vtnet0: Ethernet address: 42:63:7c:e4:6c:e3
000.000971 [ 421] vtnet_netmap_attach       max rings 1
vtnet0: netmap queues/slots: TX 1/1024, RX 1/1024
000.000972 [ 426] vtnet_netmap_attach       virtio attached txq=1, txd=1024 rxq=1, rxd=1024
virtio_pci3: <VirtIO PCI Network adapter> port 0xe0a0-0xe0bf mem 0xfea93000-0xfea93fff,0xfd800000-0xfdffffff irq 11 at device 19.0 on pci0
vtnet1: <VirtIO Networking Adapter> on virtio_pci3
vtnet1: Ethernet address: a6:2d:d5:4f:6c:f3
000.000973 [ 421] vtnet_netmap_attach       max rings 1
vtnet1: netmap queues/slots: TX 1/1024, RX 1/1024
000.000974 [ 426] vtnet_netmap_attach       virtio attached txq=1, txd=1024 rxq=1, rxd=1024
uhci1: <Intel 82801I (ICH9) USB controller> port 0xe0c0-0xe0df irq 10 at device 29.0 on pci0
usbus1 on uhci1
uhci2: <Intel 82801I (ICH9) USB controller> port 0xe0e0-0xe0ff irq 10 at device 29.1 on pci0
usbus2 on uhci2
uhci3: <Intel 82801I (ICH9) USB controller> port 0xe100-0xe11f irq 11 at device 29.2 on pci0
usbus3 on uhci3
ehci0: <Intel 82801I (ICH9) USB 2.0 controller> mem 0xfea94000-0xfea94fff irq 11 at device 29.7 on pci0
usbus4: EHCI version 1.0
usbus4 on ehci0
pcib1: <ACPI PCI-PCI bridge> mem 0xfea95000-0xfea950ff irq 10 at device 30.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> mem 0xfea96000-0xfea960ff irq 11 at device 31.0 on pci0
pci2: <ACPI PCI bus> on pcib2
acpi_syscontainer0: <System Container> on acpi0
acpi_syscontainer1: <System Container> port 0xaf00-0xaf0b on acpi0
acpi_syscontainer2: <System Container> port 0xafe0-0xafe3 on acpi0
acpi_syscontainer3: <System Container> port 0xae00-0xae13 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse Explorer, device ID 4
fdc0: <floppy drive controller (FDE)> port 0x3f2-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: does not respond
device_attach: fdc0 attach returned 6
orm0: <ISA Option ROM> at iomem 0xed000-0xeffff on isa0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
attimer0: <AT timer> at port 0x40 on isa0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
fdc0: No FDOUT register!
ppc0: cannot reserve I/O port range
Timecounters tick every 10.000 msec
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 480Mbps High Speed USB v2.0
ugen1.1: <Intel UHCI root HUB> at usbus1
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen0.1: <Intel UHCI root HUB> at usbus0
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen3.1: <Intel UHCI root HUB> at usbus3
uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen2.1: <Intel UHCI root HUB> at usbus2
uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen4.1: <Intel EHCI root HUB> at usbus4
uhub4: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
ugen0.2: <QEMU QEMU USB Tablet> at usbus0
uhid0 on uhub1
uhid0: <QEMU QEMU USB Tablet, class 0/0, rev 2.00/0.00, addr 2> on usbus0
uhub4: 6 ports with 6 removable, self powered
ugen4.2: <Apple Inc. iPhone> at usbus4
cd0 at ata1 bus 0 scbus1 target 0 lun 0
cd0: <QEMU QEMU DVD-ROM 2.5+> Removable CD-ROM SCSI device
cd0: Serial Number QM00003
cd0: 16.700MB/s transfers (WDMA2, ATAPI 12bytes, PIO 65534bytes)
cd0: 655MB (335744 2048 byte sectors)
Trying to mount root from ufs:/dev/ufsid/5c46b3cebae05a43 [rw]...
random: unblocking device.
CPU: Common KVM processor (3092.92-MHz K8-class CPU)
  Origin="GenuineIntel"  Id=0xf61  Family=0xf  Model=0x6  Stepping=1
  Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
  Features2=0x80202001<SSE3,CX16,x2APIC,HV>
  AMD Features=0x20100800<SYSCALL,NX,LM>
  AMD Features2=0x1<LAHF>
Hypervisor: Origin = "KVMKVMKVM"
vtnet0: link state changed to UP
vtnet1: link state changed to UP
pflog0: promiscuous mode enabled

I'm using an old iPhone 5C, works fine on other OSes with USB hotspot.
I suspect it's the VM or FreeBSD factor.
I think I solved the VM factor by passing the USB through the hypervisor correctly.

@akuma1x Thanks, however:

that would be a failure.
bit like 'just reboot the computer'. I prefer to find and solve the issue at hand, for future reference.
I'm trying to make the network as efficient as possible.
The fewer hardware devices:
4.1 the less points of failure
4.2 the less power costs
4.3 possibly less network bottlenecks
4.3.1 possibly less speed delays
reduces fiscal expense
cleaner network topology map
less unnecessary products

stephenw10

Ok check: usbconfig -d ugen4.2 dump_all_desc

eiger3970

Wow, a lot of output. It's beyond my understanding.

[2.4.4-RELEASE][admin@pfSense.localdomain]/.ssh: usbconfig -d ugen4.2 dump_all_desc
ugen4.2: <Apple Inc. iPhone> at usbus4, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON (500mA)

  bLength = 0x0012 
  bDescriptorType = 0x0001 
  bcdUSB = 0x0200 
  bDeviceClass = 0x0000  <Probed by interface class>
  bDeviceSubClass = 0x0000 
  bDeviceProtocol = 0x0000 
  bMaxPacketSize0 = 0x0040 
  idVendor = 0x05ac 
  idProduct = 0x12a8 
  bcdDevice = 0x0530 
  iManufacturer = 0x0001  <Apple Inc.>
  iProduct = 0x0002  <iPhone>
  iSerialNumber = 0x0003  <redactedFromPublicViewByForumPostingAuthor>
  bNumConfigurations = 0x0004 

 Configuration index 0

    bLength = 0x0009 
    bDescriptorType = 0x0002 
    wTotalLength = 0x0027 
    bNumInterfaces = 0x0001 
    bConfigurationValue = 0x0001 
    iConfiguration = 0x0005  <PTP>
    bmAttributes = 0x00c0 
    bMaxPower = 0x00fa 

    Interface 0
      bLength = 0x0009 
      bDescriptorType = 0x0004 
      bInterfaceNumber = 0x0000 
      bAlternateSetting = 0x0000 
      bNumEndpoints = 0x0003 
      bInterfaceClass = 0x0006  <Still imaging>
      bInterfaceSubClass = 0x0001 
      bInterfaceProtocol = 0x0001 
      iInterface = 0x0000  <no string>

     Endpoint 0
        bLength = 0x0007 
        bDescriptorType = 0x0005 
        bEndpointAddress = 0x0002  <OUT>
        bmAttributes = 0x0002  <BULK>
        wMaxPacketSize = 0x0200 
        bInterval = 0x000a 
        bRefresh = 0x0000 
        bSynchAddress = 0x0000 

     Endpoint 1
        bLength = 0x0007 
        bDescriptorType = 0x0005 
        bEndpointAddress = 0x0081  <IN>
        bmAttributes = 0x0002  <BULK>
        wMaxPacketSize = 0x0200 
        bInterval = 0x000a 
        bRefresh = 0x0000 
        bSynchAddress = 0x0000 

     Endpoint 2
        bLength = 0x0007 
        bDescriptorType = 0x0005 
        bEndpointAddress = 0x0083  <IN>
        bmAttributes = 0x0003  <INTERRUPT>
        wMaxPacketSize = 0x0040 
        bInterval = 0x000a 
        bRefresh = 0x0000 
        bSynchAddress = 0x0000 



 Configuration index 1

    bLength = 0x0009 
    bDescriptorType = 0x0002 
    wTotalLength = 0x0095 
    bNumInterfaces = 0x0003 
    bConfigurationValue = 0x0002 
    iConfiguration = 0x0006  <iPod USB Interface>
    bmAttributes = 0x00c0 
    bMaxPower = 0x00fa 

    Interface 0
      bLength = 0x0009 
      bDescriptorType = 0x0004 
      bInterfaceNumber = 0x0000 
      bAlternateSetting = 0x0000 
      bNumEndpoints = 0x0000 
      bInterfaceClass = 0x0001  <Audio device>
      bInterfaceSubClass = 0x0001 
      bInterfaceProtocol = 0x0000 
      iInterface = 0x0000  <no string>

      Additional Descriptor

      bLength = 0x09
      bDescriptorType = 0x24
      bDescriptorSubType = 0x01
       RAW dump: 
       0x00 | 0x09, 0x24, 0x01, 0x00, 0x01, 0x1e, 0x00, 0x01, 
       0x08 | 0x01

      Additional Descriptor

      bLength = 0x0c
      bDescriptorType = 0x24
      bDescriptorSubType = 0x02
       RAW dump: 
       0x00 | 0x0c, 0x24, 0x02, 0x01, 0x01, 0x02, 0x02, 0x02, 
       0x08 | 0x03, 0x00, 0x00, 0x00


      Additional Descriptor

      bLength = 0x09
      bDescriptorType = 0x24
      bDescriptorSubType = 0x03
       RAW dump: 
       0x00 | 0x09, 0x24, 0x03, 0x02, 0x01, 0x01, 0x01, 0x01, 
       0x08 | 0x00


    Interface 1
      bLength = 0x0009 
      bDescriptorType = 0x0004 
      bInterfaceNumber = 0x0001 
      bAlternateSetting = 0x0000 
      bNumEndpoints = 0x0000 
      bInterfaceClass = 0x0001  <Audio device>
      bInterfaceSubClass = 0x0002 
      bInterfaceProtocol = 0x0000 
      iInterface = 0x0000  <no string>


    Interface 1 Alt 1
      bLength = 0x0009 
      bDescriptorType = 0x0004 
      bInterfaceNumber = 0x0001 
      bAlternateSetting = 0x0001 
      bNumEndpoints = 0x0001 
      bInterfaceClass = 0x0001  <Audio device>
      bInterfaceSubClass = 0x0002 
      bInterfaceProtocol = 0x0000 
      iInterface = 0x0000  <no string>

      Additional Descriptor

      bLength = 0x07
      bDescriptorType = 0x24
      bDescriptorSubType = 0x01
       RAW dump: 
       0x00 | 0x07, 0x24, 0x01, 0x02, 0x01, 0x01, 0x00


      Additional Descriptor

      bLength = 0x23
      bDescriptorType = 0x24
      bDescriptorSubType = 0x02
       RAW dump: 
       0x00 | 0x23, 0x24, 0x02, 0x01, 0x02, 0x02, 0x10, 0x09, 
       0x08 | 0x40, 0x1f, 0x00, 0x11, 0x2b, 0x00, 0xe0, 0x2e, 
       0x10 | 0x00, 0x80, 0x3e, 0x00, 0x22, 0x56, 0x00, 0xc0, 
       0x18 | 0x5d, 0x00, 0x00, 0x7d, 0x00, 0x44, 0xac, 0x00, 
       0x20 | 0x80, 0xbb, 0x00


     Endpoint 0
        bLength = 0x0009 
        bDescriptorType = 0x0005 
        bEndpointAddress = 0x0081  <IN>
        bmAttributes = 0x0001  <ISOCHRONOUS>
        wMaxPacketSize = 0x00c0 
        bInterval = 0x0004 
        bRefresh = 0x0000 
        bSynchAddress = 0x0000 

      Additional Descriptor

      bLength = 0x07
      bDescriptorType = 0x25
      bDescriptorSubType = 0x01
       RAW dump: 
       0x00 | 0x07, 0x25, 0x01, 0x01, 0x00, 0x00, 0x00



    Interface 2
      bLength = 0x0009 
      bDescriptorType = 0x0004 
      bInterfaceNumber = 0x0002 
      bAlternateSetting = 0x0000 
      bNumEndpoints = 0x0001 
      bInterfaceClass = 0x0003  <HID device>
      bInterfaceSubClass = 0x0000 
      bInterfaceProtocol = 0x0000 
      iInterface = 0x0000  <no string>

      Additional Descriptor

      bLength = 0x09
      bDescriptorType = 0x21
      bDescriptorSubType = 0x11
       RAW dump: 
       0x00 | 0x09, 0x21, 0x11, 0x01, 0x00, 0x01, 0x22, 0xd0, 
       0x08 | 0x00

     Endpoint 0
        bLength = 0x0007 
        bDescriptorType = 0x0005 
        bEndpointAddress = 0x0083  <IN>
        bmAttributes = 0x0003  <INTERRUPT>
        wMaxPacketSize = 0x0040 
        bInterval = 0x0001 
        bRefresh = 0x0000 
        bSynchAddress = 0x0000 



 Configuration index 2

    bLength = 0x0009 
    bDescriptorType = 0x0002 
    wTotalLength = 0x003e 
    bNumInterfaces = 0x0002 
    bConfigurationValue = 0x0003 
    iConfiguration = 0x0007  <PTP + Apple Mobile Device>
    bmAttributes = 0x00c0 
    bMaxPower = 0x00fa 

    Interface 0
      bLength = 0x0009 
      bDescriptorType = 0x0004 
      bInterfaceNumber = 0x0000 
      bAlternateSetting = 0x0000 
      bNumEndpoints = 0x0003 
      bInterfaceClass = 0x0006  <Still imaging>
      bInterfaceSubClass = 0x0001 
      bInterfaceProtocol = 0x0001 
      iInterface = 0x0000  <no string>

     Endpoint 0
        bLength = 0x0007 
        bDescriptorType = 0x0005 
        bEndpointAddress = 0x0002  <OUT>
        bmAttributes = 0x0002  <BULK>
        wMaxPacketSize = 0x0200 
        bInterval = 0x000a 
        bRefresh = 0x0000 
        bSynchAddress = 0x0000 

     Endpoint 1
        bLength = 0x0007 
        bDescriptorType = 0x0005 
        bEndpointAddress = 0x0081  <IN>
        bmAttributes = 0x0002  <BULK>
        wMaxPacketSize = 0x0200 
        bInterval = 0x000a 
        bRefresh = 0x0000 
        bSynchAddress = 0x0000 

     Endpoint 2
        bLength = 0x0007 
        bDescriptorType = 0x0005 
        bEndpointAddress = 0x0083  <IN>
        bmAttributes = 0x0003  <INTERRUPT>
        wMaxPacketSize = 0x0040 
        bInterval = 0x000a 
        bRefresh = 0x0000 
        bSynchAddress = 0x0000 


    Interface 1
      bLength = 0x0009 
      bDescriptorType = 0x0004 
      bInterfaceNumber = 0x0001 
      bAlternateSetting = 0x0000 
      bNumEndpoints = 0x0002 
      bInterfaceClass = 0x00ff  <Vendor specific>
      bInterfaceSubClass = 0x00fe 
      bInterfaceProtocol = 0x0002 
      iInterface = 0x000d  <Apple USB Multiplexor>

     Endpoint 0
        bLength = 0x0007 
        bDescriptorType = 0x0005 
        bEndpointAddress = 0x0004  <OUT>
        bmAttributes = 0x0002  <BULK>
        wMaxPacketSize = 0x0200 
        bInterval = 0x0000 
        bRefresh = 0x0000 
        bSynchAddress = 0x0000 

     Endpoint 1
        bLength = 0x0007 
        bDescriptorType = 0x0005 
        bEndpointAddress = 0x0085  <IN>
        bmAttributes = 0x0002  <BULK>
        wMaxPacketSize = 0x0200 
        bInterval = 0x0000 
        bRefresh = 0x0000 
        bSynchAddress = 0x0000 



 Configuration index 3

    bLength = 0x0009 
    bDescriptorType = 0x0002 
    wTotalLength = 0x0075 
    bNumInterfaces = 0x0003 
    bConfigurationValue = 0x0004 
    iConfiguration = 0x0008  <PTP + Apple Mobile Device + Apple USB Ethernet>
    bmAttributes = 0x00c0 
    bMaxPower = 0x00fa 

    Interface 0
      bLength = 0x0009 
      bDescriptorType = 0x0004 
      bInterfaceNumber = 0x0000 
      bAlternateSetting = 0x0000 
      bNumEndpoints = 0x0003 
      bInterfaceClass = 0x0006  <Still imaging>
      bInterfaceSubClass = 0x0001 
      bInterfaceProtocol = 0x0001 
      iInterface = 0x0000  <no string>

     Endpoint 0
        bLength = 0x0007 
        bDescriptorType = 0x0005 
        bEndpointAddress = 0x0002  <OUT>
        bmAttributes = 0x0002  <BULK>
        wMaxPacketSize = 0x0200 
        bInterval = 0x000a 
        bRefresh = 0x0000 
        bSynchAddress = 0x0000 

     Endpoint 1
        bLength = 0x0007 
        bDescriptorType = 0x0005 
        bEndpointAddress = 0x0081  <IN>
        bmAttributes = 0x0002  <BULK>
        wMaxPacketSize = 0x0200 
        bInterval = 0x000a 
        bRefresh = 0x0000 
        bSynchAddress = 0x0000 

     Endpoint 2
        bLength = 0x0007 
        bDescriptorType = 0x0005 
        bEndpointAddress = 0x0083  <IN>
        bmAttributes = 0x0003  <INTERRUPT>
        wMaxPacketSize = 0x0040 
        bInterval = 0x000a 
        bRefresh = 0x0000 
        bSynchAddress = 0x0000 


    Interface 1
      bLength = 0x0009 
      bDescriptorType = 0x0004 
      bInterfaceNumber = 0x0001 
      bAlternateSetting = 0x0000 
      bNumEndpoints = 0x0002 
      bInterfaceClass = 0x00ff  <Vendor specific>
      bInterfaceSubClass = 0x00fe 
      bInterfaceProtocol = 0x0002 
      iInterface = 0x000d  <Apple USB Multiplexor>

     Endpoint 0
        bLength = 0x0007 
        bDescriptorType = 0x0005 
        bEndpointAddress = 0x0004  <OUT>
        bmAttributes = 0x0002  <BULK>
        wMaxPacketSize = 0x0200 
        bInterval = 0x0000 
        bRefresh = 0x0000 
        bSynchAddress = 0x0000 

     Endpoint 1
        bLength = 0x0007 
        bDescriptorType = 0x0005 
        bEndpointAddress = 0x0085  <IN>
        bmAttributes = 0x0002  <BULK>
        wMaxPacketSize = 0x0200 
        bInterval = 0x0000 
        bRefresh = 0x0000 
        bSynchAddress = 0x0000 


    Interface 2
      bLength = 0x0009 
      bDescriptorType = 0x0004 
      bInterfaceNumber = 0x0002 
      bAlternateSetting = 0x0000 
      bNumEndpoints = 0x0000 
      bInterfaceClass = 0x00ff  <Vendor specific>
      bInterfaceSubClass = 0x00fd 
      bInterfaceProtocol = 0x0001 
      iInterface = 0x0000  <no string>


    Interface 2 Alt 1
      bLength = 0x0009 
      bDescriptorType = 0x0004 
      bInterfaceNumber = 0x0002 
      bAlternateSetting = 0x0001 
      bNumEndpoints = 0x0002 
      bInterfaceClass = 0x00ff  <Vendor specific>
      bInterfaceSubClass = 0x00fd 
      bInterfaceProtocol = 0x0001 
      iInterface = 0x0000  <no string>

     Endpoint 0
        bLength = 0x0007 
        bDescriptorType = 0x0005 
        bEndpointAddress = 0x0086  <IN>
        bmAttributes = 0x0002  <BULK>
        wMaxPacketSize = 0x0200 
        bInterval = 0x0000 
        bRefresh = 0x0000 
        bSynchAddress = 0x0000 

     Endpoint 1
        bLength = 0x0007 
        bDescriptorType = 0x0005 
        bEndpointAddress = 0x0005  <OUT>
        bmAttributes = 0x0002  <BULK>
        wMaxPacketSize = 0x0200 
        bInterval = 0x0000 
        bRefresh = 0x0000 
        bSynchAddress = 0x0000 


    Interface 2 Alt 2
      bLength = 0x0009 
      bDescriptorType = 0x0004 
      bInterfaceNumber = 0x0002 
      bAlternateSetting = 0x0002 
      bNumEndpoints = 0x0002 
      bInterfaceClass = 0x00ff  <Vendor specific>
      bInterfaceSubClass = 0x00fd 
      bInterfaceProtocol = 0x0001 
      iInterface = 0x0000  <no string>

     Endpoint 0
        bLength = 0x0007 
        bDescriptorType = 0x0005 
        bEndpointAddress = 0x0086  <IN>
        bmAttributes = 0x0002  <BULK>
        wMaxPacketSize = 0x0200 
        bInterval = 0x0000 
        bRefresh = 0x0000 
        bSynchAddress = 0x0000 

     Endpoint 1
        bLength = 0x0007 
        bDescriptorType = 0x0005 
        bEndpointAddress = 0x0005  <OUT>
        bmAttributes = 0x0002  <BULK>
        wMaxPacketSize = 0x0200 
        bInterval = 0x0000 
        bRefresh = 0x0000 
        bSynchAddress = 0x0000

stephenw10

The important part appears to be this though:

Configuration index 3

    bLength = 0x0009 
    bDescriptorType = 0x0002 
    wTotalLength = 0x0075 
    bNumInterfaces = 0x0003 
    bConfigurationValue = 0x0004 
    iConfiguration = 0x0008  <PTP + Apple Mobile Device + Apple USB Ethernet>
    bmAttributes = 0x00c0 
    bMaxPower = 0x00fa

It needs to be using index 3. Try:
usbconfig -d ugen4.2 set_config 3

Steve

stephenw10

@eiger3970 said in IPhone Tethering to pfSense:

idVendor = 0x05ac
idProduct = 0x12a8

That looks like it should be recognised as an iphone5 actually:
https://github.com/pfsense/FreeBSD-src/blob/RELENG_2_4_4/sys/dev/usb/usbdevs#L1168

eiger3970

Oh wow!
pfSense GUI > Interfaces > Interface Assignments > shows Available network ports: ue0

I will try to follow a GUI guide now for the final setup.

Yes, the USB device is an iPhone 5C.

'It' needs to be using index 3...is it referring to the iPhone or pfSense?

eiger3970

Ok, pfSense reboot needs the setup run each time. I won't be rebooting the router much, so that's ok, until perhaps the kernel module if_ipheth.ko udates the code?
I.e.:
usbconfig -d ugen4.2 set_config 3.

So, running the GUI:
pfSense 2.4.4-RELEASE-p2 > Interfaces > Assignments > Add ue0 (Ma:cA:dd:re:ss:00) > OPT1 ue0 appears > Save > Interfaces > OPT1 > General Configuration > Enable: tick Enable interface > IPv4 Configuration Type: DHCP > Save > Apply Changes > System > Routing > Gateways > OPT1_DHCP should be Default > pfSense shell: netstat -r > Enter > problem as ue0 is in Internet 6 and not in Internet?

eiger3970

If it helps, here are my network topologies from Ethernet modem to USB modem.
Ethernet modem:
alt text

USB modem:
alt text

Perhaps the USB modem topology needs the net0 = vmbr1 to be updated to OPT1 = vmbr1?

stephenw10

Ok great if config index 3 works you can have that set every time at boot using a usb quirk
https://www.freebsd.org/cgi/man.cgi?query=usb_quirk

Add to /boot/loader.conf.local:
hw.usb.quirk.0="0x05ac 0x12a8 0 0xffff UQ_CFG_INDEX_3"

There real issue with this type of setup is that if the phone switches off or is unplugged or in some other way is no longer present and you reboot pfSense it will fail to boot. It will stop at the interfaces assign screen because it has ue0 in it's config and it isn't there.

Steve

eiger3970

Thank you, that works after a reboot.
I updated file /boot/loader.conf, there was not file /boot/loader.conf.local.

So, the final thing is configuring pfSense GUI to pass data.
Interfaces > Assignments > OPT1 ue0 (53:f9:38:33:18:4f).
Interfaces > OPT > Enabled interface. IPv4 Configuration Type: DHCP.
System > Routing > Gateways > OPT1_DHCP is Default (IPv4).
Dashboard > Interfaces > OPT1 > green up arrow with IP 0.0.0.0.

stephenw10

Yeah, you will have to create the .local file but you should put both lines in there. The standard loader.conf file can be overwritten by changes in pfSense.

If it's not pulling an IP address that would seem to be some setting in the iphone. Is tethering actually enabled there?
Does it work as a wireless hotspot?

Steve

eiger3970

Oh, thank you.
Done.

Tethering is enabled. No wifi on the hypervisor.
I'll check the hardware tomorrow.

[2.4.4-RELEASE][admin@pfSense.localdomain]/boot: netstat -r
Routing tables

Internet:
Destination        Gateway            Flags     Netif Expire
0.0.0.0/8          link#1             U        vtnet0
localhost          link#4             UH          lo0
192.168.1.0/24     link#2             U        vtnet1
pfSense            link#2             UHS         lo0

Internet6:
Destination        Gateway            Flags     Netif Expire
localhost          link#4             UH          lo0
fe80::%vtnet0/64   link#1             U        vtnet0
fe80::4063:7cff:fe link#1             UHS         lo0
fe80::%vtnet1/64   link#2             U        vtnet1
fe80::a42d:d5ff:fe link#2             UHS         lo0
fe80::%lo0/64      link#4             U           lo0
fe80::1%lo0        link#4             UHS         lo0
fe80::%ue0/64      link#7             U           ue0
fe80::5cf9:38ff:fe link#7             UHS         lo0