Can I use one of my 6 physical network ports to be a vpn port?
-
@mbc0 said in Can I use one of my 6 physical network ports to be a vpn port?:
I have tried setting the ip of the source network to 192.168.2.1
Why are you trying to set an IP... You would NOT set an ip on a vpn client connect to some vpn service..
Their guides are written by idiots for their idiot users.. Sorry but that is my personal opinion of these nonsense service..
Point to me in their guide where it says to set an IP on your interface???
Lets say you where required to set a static on the interface - you still can not have the same network locally as your tunnel network.. You can not use 192.168.2/24 on one of your networks, and 192.168.2/24 as your tunnel to the vpn service..
Where is your gateway??? You manually created that gateway pointing to your own local interface on 192.168.2.1??
So you didn't follow there guide at all!! Is what your saying - your just saying you did... Because no where in there does it say to do that...
What I would suggest is just remove ALL the settings for any vpn anything... Switch to normal automatic and then get this new network working... Then setup your vpn!
-
Hi,
Firstly, I understand your frustration and I totally get it! I am an engineer of 30 years and find it very frustrating explaining things to people that just cannot understand what I am explaining. Please remember I am a complete novice trying my best to understand and follow what I thought was an official guide from PIA which has in it's defence worked for all my interfaces but I need it to work for just one interface, the guide does not cover that.
> Why are you trying to set an IP... You would NOT set an ip on a vpn client connect to some vpn service..]
I was doing this as unless I specified an IP it just stays at dynamic and does not show an IP
> Their guides are written by idiots for their idiot users.. Sorry but that is my personal opinion of these nonsense service..]
I understand your opinion :-)
> Point to me in their guide where it says to set an IP on your interface???
It does not say this anywhere in the guide as their guide is only to put all interfaces behind the vpn which as I previously stated works, I cannot find any guide or understand any way to do this for just one interface.
> Lets say you where required to set a static on the interface - you still can not have the same network locally as your tunnel network.. You can not use 192.168.2/24 on one of your networks, and 192.168.2/24 as your tunnel to the vpn service..
I am so sorry I am not fully understanding this, I have 4 interfaces in use
wan
lan - I set an IP of 192.168.0.10
Unifi - I set an IP of 192.168.1.5
PIAVPN - I set an IP of 192.168.2.1> Where is your gateway??? You manually created that gateway pointing to your own local interface on 192.168.2.1??
So you didn't follow there guide at all!! Is what your saying - your just saying you did... Because no where in there does it say to do that...
Yes I did follow the guide completely and it worked perfectly but for all interfaces, I need this to be on just one interface.
What I would suggest is just remove ALL the settings for any vpn anything... Switch to normal automatic and then get this new network working... Then setup your vpn!
I have had this interface working fine the whole time and have been using it for some months before trying to get OpenVPN working.
In a nutshell
All interfaces have been working fine for some time now.
I followed the PIA Guide and all worked great for all interfaces then the problem is trying to get it to work just on one interface.Again, I really am genuinly sorry as I know how frustrating this must be.
Thanks
-
Dude... You can do this with 1 interface, 100 interfaces... Doesn't matter its a simple policy route... You have gateway that is the vpn connection... creat a rule that sends who you want when they want go X out the gateway... its that freaking simple..
All that is required for you to do this, is follow their stupid guide and don't pull the routes. Then nobody will be using the vpn
Other than their nonsense about deleting your wan outbound nats as their kill switch.. OMG!!!
Now create a rule that points either the whole network or a specific IP out the gateway...
That is ALL there is too it... Have you read the policy routing documentation?
https://docs.netgate.com/pfsense/en/latest/routing/directing-traffic-with-policy-routing.html
edit: Here... I just created a firewall rule to point my client out the vpn.. Its as simple as changing the gateway from default to the vpn.. That is all there is too it... When you pull the routes, they change your DEFAULT to use the vpn... For anything to no use the vpn you would have to force it out your wan gateway..
Reason the other site for IP is different, is I didn't want to flush my states, so I went somewhere different (not google) to create a new state on the firewall and use the vpn connection, vs the previous states that were using my wan.
-
Thank you, I can see now I was on the wrong path and overthinking.
I believe I am understanding this (mostly) now and have been through what you said and the Policy Routing Configuration many times, I have mostly started again but cannot get my vpn gateway to register an IP.
I cannot get anything other than dynamic to show for my Gateway
Do I need a rule for this interface?
I have been over and over and feel I have things setup right now, I just cannot see why the gateway is stuck on dynamic? -
AHA!
A Break Through!!!
I now have an IP!
In the firewall rules I had the vpn interface selected instead of the physical interface!
All I have to do now is work out how to get any devices on the interface to the correct gateway as there is no internet on the physical port (IPCONFIG shows the gateway as 192.168.2.1 which is the address of the physical port) but this is so close now :-)
Thank you SOOO much for your help and I hope I never caused you to lose too much hair :-D
-
@mbc0 said in Can I use one of my 6 physical network ports to be a vpn port?:
(IPCONFIG shows the gateway as 192.168.2.1 which is the address of the physical port) but this is so close now :-)
Huh?? When you create a new network on pfsense there would be NO GATEWAY set.. When you do that it becomes a WAN..
So in pfsense you would have an interface
192.168.2.1/24 for example.. NO GATEWAY!!! NONE!!!
Here is one of my network..
Clients on this network, say your box you want to use your vpn would use pfsense IP as "their" gateway 192.168.2.1 for example if that is what you set pfsense to be, or example mine is 192.168.4.253..
What I suggest you get this network working going out your normal wan - than Policy route it out your vpn!!!
-
-
Now with your nat set to auto any clients on this network should work.. You created a any any rule on this interface right?
-
hmmm with nat set to auto, Windows changes from no internet shown on the connection to showing internet is now available but there is no response to the outside world, the other LAN & UNIFI interfaces are working fine
-
I have a Windows 10 Laptop solely connected to the vpn interface FYI
And yes I do have an any rule
-
I removed the gateway from the interface but still the same, no internet
-
well how is internet going to work with just TCP... dns is UDP... to lookup www.internet.com you need to be able to talk UDP.
-
A schoolboy error.. no idea how that happened!
I have just put everything back and its working!! I am so relieved! and yes it is so bloody easy now I know how it all comes together, you must have been pulling your hair out! I am going to do this again on another server just to prove to myself how easy it is :-)
All I have now is a dns leak but have seen plenty of info on how to resolve that!
Thanks so so much!
-
One think I have noticed though, although everything is working (apart from the DNS Leak)
The VPN Gateway is showing as offline?
-
What version are you running? That is not current version..
Oh your in the status section.. Thats why it looks different.. Restart the vpn instance.
Really dude your hiding a 10 address?
-
haha, yes, I did hide the 10 address but not intentionally! :-D
-
That is not current.. current is
2.4.4-RELEASE-p3 (amd64)
built on Thu May 16 06:01:19 EDT 2019
FreeBSD 11.2-RELEASE-p10Well now 2.4.5 is, it just dropped..
Version 2.4.5 is available.
Version information updated at Thu Mar 26 11:19:06 CDT -
hmmm ok...
I run pfsense (for nearly 2 years now) as a vm on a HP Microserver running unraid, I wonder why it doesn't update automatically? I will look to see how to update now, are there any pitfalls I should be aware of jumping from 2.4.3 to 2.45?
Thank you
-
Well 2.4.5 just dropped like maybe an hour a ago.. at best... So prob wouldn't update just yet... Oh but your on a VM... Oh then just take a snapshot and click the button... Use to do that all the time when running on vm.. Even daily snapshots I would run - because could just rollback to the snapshot took before I clicked upgrade..
-
