Running pfSense 2.4.4 over a KVM VM in PROXMOX 6.1.5.

ramses.sevilla

@viragomann, very thanks by your answer.

I have configured the VM as tells in the link that you send me.

Only have one difference:

In the link puts the disk as VirtIO and I have the disk as SCSI VirtIO.

Do you think that this can be the problem?

Regards,

Ramsés

viragomann

No, that want matter here.
But did you disable "Hardware Checksum Offloading" as recommended?

ramses.sevilla

@viragomann, yes, I had disabled "Hardware Checksum Offloading" too.

I followed the manual of the link when I installed pfSense over PROXMOX.

Regards,

Ramsés

ramses.sevilla

@viragomann, the installation is done fast but when It restarts it stucks here.

Here.

And here.

I have installed the latest version of PROXMOX and It is updated.

This is the KVM VM configuration:

root@proxmox:~# qm config 750                         balloon: 0
bootdisk: scsi0
cores: 2                                              cpu: kvm64
ide2: local:iso/pfSense-CE-2.4.4-RELEASE-p3-amd64.iso,media=cdrom,size=680214K
memory: 4096
net0: virtio=E6:9F:61:80:C9:6A,bridge=vmbr0
numa: 0                                               onboot: 1
ostype: l26
scsi0: local-lvm:vm-750-disk-0,size=15G               scsihw: virtio-scsi-pci
smbios1: uuid=204a6db6-26d7-4dc7-8839-4478c192179e
sockets: 1
vmgenid: 832d7332-4977-47ae-9b02-0cf5826ba5f3
root@proxmox:~#

I unknow what happen...

Regards,

Ramsés

viragomann

You've selected a wrong OS Type, "other" should be used for pfSense.

Don't know if it matters, but I recommend to use the host cpu type.

Also you might be able to change the disk type to virtIO by editing the config file in nano.

stephenw10

I have several pfSense VMs running in Proxmox with various OS types set (now that I check!). All are running VirtIO SCSI without issue.
My PVE version is a little out of date though, 6.0-5.

Steve

ramses.sevilla

@viragomann, I had changed OS Type in the VM to the others Linux SO Type and the VM took the same time to booting.

@viragomann / @stephenw10, I had installed on a VM:

pfSense-CE-2.4.4-RELEASE-p3-amd64

And It took a lot of time to booting.

I have installed on another VM:

pfSense-CE-2.4.5-RELEASE-amd64

And It takes much less time to booting.

I have upgrade pfSense 2.4.4-p3 to 2.4.5 on first VM and It takes much less time to booting.

The VM config:

root@proxmox:/# qm config 750
balloon: 0
bootdisk: scsi0
cores: 2
cpu: kvm64
ide2: local:iso/pfSense-CE-2.4.5-RELEASE-amd64.iso,media=cdrom,size=720684K
memory: 4096
net0: virtio=E6:9F:61:80:C9:6A,bridge=vmbr0
numa: 0
onboot: 1
ostype: l26
scsi0: local-lvm:vm-750-disk-1,iothread=1,size=15G
scsihw: virtio-scsi-pci
smbios1: uuid=204a6db6-26d7-4dc7-8839-4478c192179e
sockets: 1
tablet: 0
vmgenid: 832d7332-4977-47ae-9b02-0cf5826ba5f3
root@proxmox:/#

I think that the problem is of the pfSense 2.4.4-p3 version, isen't It?

Another question:

UFS or ZFS to do the install pfSense over the VM?.

I have tried / tested both but what do you think?

Regards,

Ramsés

stephenw10

On a VM the usual benefits of ZFS are often not there. Snaphots and the fact the host will probably stay up removes them.

Mine are all running UFS unless I'm testing ZFS specifically.

Steve

ramses.sevilla

Hi again,

First time, thanks so much both by your answers.

Now, I have some questions:

@stephenw10 , would It have any problem of performance if I configure ZFS instead of UFS the Disk in the VM?

About how long should it takes to booting a KVM with pfSense in PROXMOX?

And I have found an incongruity in the documentation:

In this link (Virtualizing pfSense with Proxmox):

https://docs.netgate.com/pfsense/en/latest/virtualization/virtualizing-pfsense-with-proxmox.html

Tells that configure the Network Interface Model VirtIO.

But in this other link (Configuring High Availability):

https://docs.netgate.com/pfsense/en/latest/highavailability/configuring-high-availability.html?highlight=high%20availability

Tells that configure the Network Interface Model E1000.

What should be the Network Interface Model configured really?

Regards,

Ramsés

stephenw10

I'm using VirtIO NICs (vtnet) for everything and have never seen an issue.
The ed(4) driver is for ancient hardware. I don't think Proxmox supports that any longer. I imagine when that guide was written those may have been the only choices.

Steve

ramses.sevilla

@viragomann sorry, I had no see the CPU recommendation:

Host CPU Type gives better performance that KVM64 CPU Type in the VM?

Regards,

Ramsés

viragomann

You will get the best benefits of the processor features, when using host type. This passes all the features of the processor through to the VM, while KVM64 provides only a small amount of common features. For instance, KVM64 doesn't make use of AES-NI, even if your host CPU supports it.

rayures

@viragomann said in Running pfSense 2.4.4 over a KVM VM in PROXMOX 6.1.5.:

You will get the best benefits of the processor features, when using host type. This passes all the features of the processor through to the VM, while KVM64 provides only a small amount of common features. For instance, KVM64 doesn't make use of AES-NI, even if your host CPU supports it.

with kvm64 you can set extra cpu flags though, including AES. All via proxmox gui.