Zotac CI323 Installation - Controller Failures

stephenw10

@ac0hen said in Zotac CI323 Installation - Controller Failures:

bsdlabel -B -r -w ada0s1 auto" command, it stops at 77% (every time). Then a "ahcich1" Timeout on slot 21 port 0" and "(ada0:ahcich1:0:0:0): CAM status: Command timeout

With that same error?

drzow

I am having the same issue on initial boot on a Minis / Besstar Z83-F, which is another one of these tiny Intel Cherry Trail boxes. Trying to do an initial install, I am using a memstick, option 3 to launch the boot loader, then I type in:

set hw.sdhci.enable_msi=0
set hint.sdhci_pci.0.disabled=1
set hint.sdhci_pci.1.disabled=1
boot

and the kernel goes on its merry way, but I still end up hanging after the ppc0: cannot reserve I/O port range -- never actually get to the installer. Am I doing something wrong with setting the parameters?
Thanks!
Terry

stephenw10

The ppc0 (parallel port) error is common on many systems and should not prevent it booting.

What error are you seeing that makes you think you need to disable sdhci?

Steve

drzow

Thanks Steve! Agreed that the ppc0 error isn't the actual problem, but rather the hang after it, which you thought was sdhci related in this other thread. It seems to be endemic to these Cherry Trail boards. Some other forums also indicated that it's the eMMC, which if memory serves is the same thing as sdhci.
Thanks!
Terry

stephenw10

Hmm, I thought there was a thread for the UP board here. It's probably worth looking through that if you have not already.

Edit: This maybe? https://forum.netgate.com/post/743676

Steve

drzow

Ah-ha! Gave that a shot, but the Z83-F BIOS is just different enough from the UP boards that I couldn't get it to work. I was, however, able to uncover another lead that led me to this FreeBSD forum post, where it discusses the UARTs being the problem, so I:

set hint.uart.0.disabled="1"
set hint.uart.1.disabled="1"

and the kernel now boots and the installer is running!!!

I really appreciate your persistence on this Steve!

Terry

Orbixx

@dlm274 said in Zotac CI323 Installation - Controller Failures:

just to document, because i found this thread on google searching for the same problem:

create the file /boot/loader.conf.local with following content:
hw.sdhci.enable_msi=0
hint.sdhci_pci.0.disabled=1
hint.sdhci_pci.1.disabled=1
That's update safe (tested on my own machine from today) and the second hint.sdhci is needed for the ZBOX CI327.

Now everything works like a charm on the pfsense with this little beast. Tested with 500MBit uplink and OpenVPN (AES CPU-Hardwareaccellerator enabled) - no limitations.

73 dlm274

Reviving the topic again one year later!

I was installing on a new Fitlet 2 recently as my old home pfSense device started powering off when it hit around the 45 degree Celsius temperature mark. I encountered the same problem with the SD card causing command timeouts and the above boot params solved the problem.

Netgate, do the contents of /boot/loader.conf.local get processed in the pfSense config backup/restore function? Or would I have to reconfigure this again manually if say my disk died and I had to replace it?

I assume the root cause of this issue would have to be handled upstream in FreeBSD? Doesn't seem specific to pfSense. Did anybody submit a bug report?

stephenw10

The contents of loader.conf.local do not get added to the config file which is the only thing that is backed up by backup restore.
I thought there was a bug open for this already....

Steve

noconnor

Thanks for mentioning the Fitlet, @Orbixx. I was just setting one up today and I'm optimistic this will be the solution to my issue too.

Orbixx

@stephenw10 Upstream or within pfSense? I can't find a bug report specific to this in either place.

I wonder if this will be fixed in 2.5 with the upgrade to FreeBSD 12.

@noconnor Any luck?

stephenw10

I thought there was a single upstream eMMC controller bug in FreeBSD 11 that was triggering mist of these issues but I can't find it now. It may well be fixed in 12. Try a 2.5 snapshot and find out if you can.

Steve

noconnor

@Orbixx said in Zotac CI323 Installation - Controller Failures:

@noconnor Any luck?

I added those entries to /boot/loader.conf.local and that has definitely bypassed the boot issues. ~~I did try adding those elements to System > Advanced > System Tunables (for config backup) but couldn't get that to work. I'm pretty sure that was a just me entering them wrong.~~

I haven't tried moving over to a 2.5 version yet to see if that makes a difference.

edit:
Actually, reading the docs for System Tunables, it looks like I was mistaken and those values (Loader Tunables) are not applicable to System Tunables.