2.4.5-p1 crash report

jimp

That doesn't have enough information to suggest what the problem might be. Both of you need to post the whole crash dump, or at least the ddb.txt and msgbuf.txt from inside the crash dump archive.

tomahhunt

I did wonder. OK mine is attached.
textdump.tar.0

jimp

Fatal double fault
rip 0xffffffff80de1ba4 rsp 0 rbp 0xfffffe01ee369870
rax 0xee369820 rdx 0x6 rbx 0xfffff801543cdc00
rcx 0 rsi 0xfffff80006419b7c rdi 0xfffff80154619012
r8 0xfffff801543cdc00 r9 0xd r10 0
r11 0xfffffe01ee358000 r12 0xfffff800064edd00 r13 0x6488
r14 0xfffff8015461900c r15 0xfffff80006661800 rflags 0x10246
cs 0x20 ss 0x28 ds 0x3b es 0x3b fs 0x13 gs 0x1b
fsbase 0x800762f30 gsbase 0xffffffff83522e80 kgsbase 0
cpuid = 0; apic id = 00
panic: double fault
cpuid = 0
KDB: enter: panic

db:0:kdb.enter.default>  show pcpu
cpuid        = 0
dynamic pcpu = 0xc02580
curthread    = 0xfffff800065de620: pid 12 "irq259: virtio_pci2"
curpcb       = 0xfffffe01ee369b80
fpcurthread  = none
idlethread   = 0xfffff80006241000: tid 100003 "idle: cpu0"
curpmap      = 0xffffffff834f1c40
tssp         = 0xffffffff835a32d0
commontssp   = 0xffffffff835a32d0
rsp0         = 0xfffffe01ee369b80
gs32p        = 0xffffffff835a9f28
ldt          = 0xffffffff835a9f68
tss          = 0xffffffff835a9f58
tlb gen      = 2674103
db:0:kdb.enter.default>  bt
Tracing pid 12 tid 100072 td 0xfffff800065de620
kdb_enter() at kdb_enter+0x3b/frame 0xffffffff83484040
vpanic() at vpanic+0x19b/frame 0xffffffff834840a0
panic() at panic+0x43/frame 0xffffffff83484100
dblfault_handler() at dblfault_handler+0x1de/frame 0xffffffff834841d0
Xdblfault() at Xdblfault+0xbd/frame 0xffffffff834841d0
--- trap 0x17, rip = 0xffffffff80de1ba4, rsp = 0, rbp = 0xfffffe01ee369870 ---
ether_nh_input() at ether_nh_input+0x314/frame 0xfffffe01ee369870
netisr_dispatch_src() at netisr_dispatch_src+0xa2/frame 0xfffffe01ee3698c0
ether_input() at ether_input+0x26/frame 0xfffffe01ee3698e0
vtnet_rxq_eof() at vtnet_rxq_eof+0x7ae/frame 0xfffffe01ee3699b0
vtnet_rx_vq_intr() at vtnet_rx_vq_intr+0x71/frame 0xfffffe01ee3699e0
intr_event_execute_handlers() at intr_event_execute_handlers+0xe9/frame 0xfffffe01ee369a20
ithread_loop() at ithread_loop+0xe7/frame 0xfffffe01ee369a70
fork_exit() at fork_exit+0x83/frame 0xfffffe01ee369ab0
fork_trampoline() at fork_trampoline+0xe/frame 0xfffffe01ee369ab0

Unfortunately no solid leads there that I recognize and nothing turned up in a search that exactly matched it. The closest I could find is that it could be a concurrency issue in the driver, though that particular result was 8 years old and unlikely to still be the case.

Have you changed any settings like net.isr.dispatch? What is the current value reported by sysctl net.isr.dispatch?

Since that is vtnet, make sure you have all offloading disabled. Go under System > Advanced, Networking tab, and under Network Interfaces, make sure all three offloading boxes are checked.

tomahhunt

All the offloading is disabled. Very slow without that!
net.isr.dispatch is "direct" as reported on the command line.

The only other manual setting I changed was net.inet.ip.fastforwarding to 1 when i was debugging the multi cpu issues on 2.4.5 before people worked out the underlying cause. Should I undo that?

jimp

That knob doesn't exist in 2.4.x so it wouldn't affect anything

tomahhunt

Aside from the upgrade to 2.4.5-p1 and adding more cpus back to my VM the only other recent change was a new internet connection.
So I switched to PPPoE for my WAN as I got fibre.

jimp

If it was due to the PPPoE I'd expect to see things like mpd and netgraph in the backtrace and it isn't there, just vtnet. The debug output mentions virtio_pci2 which is this:

virtio_pci2: <VirtIO PCI Network adapter> port 0xe0c0-0xe0df mem 0xfea92000-0xfea92fff,0xfe408000-0xfe40bfff irq 10 at device 18.0 on pci0
vtnet0: <VirtIO Networking Adapter> on virtio_pci2
vtnet0: Ethernet address: 96:92:4d:86:43:0e
vtnet0: netmap queues/slots: TX 1/256, RX 1/128
000.002009 [ 503] vtnet_netmap_attach       vtnet attached txq=1, txd=256 rxq=1, rxd=128

I see you are using netmap, so suricata? It could be related to that.

jimp

Ah, nevermind on the netmap that's just what the driver prints at boot regardless. I checked one of my proxmox VMs and it's there, too

tomahhunt

I don't have many packages.
bandwidthd
iperf
openvpn-client-export
pfBlockerNG-devel

There is a new version of pfBlockerNG-devel so i will update that just in case.

tomahhunt

Interesting. It just crashed again.
Never had this before and been running 2.4.5 for a long while.
Tempted to go back to 1 cpu for a bit and see if that helps.

tomahhunt

No crash in 24 hours after back to 1 cpu.
Will keep monitoring.

tomahhunt

Crashed again.
Any idea what else I might do to aid debug?