Multicast

louis2

If multicast is in and stays(!) in a dedicated vlan, it is not necessary to send it through a router. And I agree completely, you should not do that because of the added latency.

However, if the multicast source is in a different vlan as the multicast receiver/destination, than you need to route that. And that will probably be at the users premises and not in the telecom network.

Note that my provider is sending the TV-streams in a different vlan than the internet, and that the set-top-box is supposed to be connected to that tv-vlan.

Louis

DaddyGo

@louis2 said in Multicast:

TV-streams

in this case you have to route the traffic

johnpoz

@louis2 said in Multicast:

Note that my provider is sending the TV-streams in a different vlan than the internet, and that the set-top-box is supposed to be connected to that tv-vlan.

The way I take that... Is you should split that traffic at layer 2 when it comes in. So your STB would not be behind the layer 3 device..

Now keep in mind only half way through my first cup of coffee but would you do something like this..

Where you split the L2 networks before pfsense.

louis2

John,

I think the same with one small difference, being that the Ls2-switch is inside the ISP-device.

Not 100% sure, because I have internet and telephone from the ISP and television from the Cable.

Louis

louis2

To be even more precise, I have the lan-connection(s) from the ISP-device connected to my 1G-coreswitch. At the entrance port of that switch the lan is transformated to a vlan (PID=internet-vlan-no).

The Internet VLAN is entering pfSense, the TV-vlan (if present), is passing pfSense / stays level2.

Louis

johnpoz

@louis2 said in Multicast:

is passing pfSense / stays level2.

Doesn't work that way, pfsense is a layer 3 device. Pfsense is not going to pass on vlan tags.. Nor layer 2 traffic..

Sniffing on pfsense is seeing the vlan traffic.. Then put switch in front of pfsense to send the STB vlan to the devices that are suppose to be on that vlan..

hsv

My problem is that it is mail traffic that's coming in and goes to a loadbalancer (MS) this loadbalancer use multicast.
So the router need to communicate to this multicast unit.

I have tried to look into HAProxy, whit absolut not succes. The documentation I have found do not help me at all.

So if som body can point med to a HAproxy description, where you have one front ip number with multiple Ports to 2 or more servers in the backend that could help, as I cannot see pfsense handle this multicast problem.

Regards
Henning

louis2

@johnpoz

John, I know. The description of my network was over simplified. pfSense is not really in the middle of the 1G and 10G core switches.

I have a 1G-network towards most rooms and towards the ISP-device. That network is handled by the 1G-core. And I have a 10G network which connects my server, my nas and my main-PC.

Both (physical) networks are connected to pfSense for routing between the VLANs independent from the fact if they are located in the 1G or in the 10G domain.

pfSense is connected to the 1G-switch via a 1G-lagg and connected to the 10G-switch via a 10G-up and a 10G-down link. However there is also a direct (physical) connection between those two switches.

To take the TV-VLAN as example, is a vlan starting at the ISP-device, passing the 1G-core ending on one of the small Netgear switches in the living room.

Louis

louis2

@hsv

I am not an expert related to loadballancers etc, so wait for the reaction form @johnpoz etc, but to me it sounds strange that the devices like that are based on multicast.

I would expect to see some routing protocol there.

Louis

johnpoz

Ok that makes sense.

To be honest I have no idea what @hsv is talking about.. Load balancer that uses multicast??

For example

host with multicast 192.168.0.10 it do not reply.

That is NOT a multicast address.. So I have a funny suspicion there is some misuse of terms going on.

DaddyGo

@johnpoz said in Multicast:

To be honest I have no idea what @hsv is talking about.. Load balancer that uses multicast??

from the beginning I have the same feeling John

192.168.0.10 RFC1918

this has nothing to do with multicast

+++edit:

for @hsv :
https://en.wikipedia.org/wiki/Multicast_address

johnpoz

Maybe if he sends some traffic to this device at 192.168.0.10, it multicasts the traffic that is sends on?

@hsv really going to need a bit more info.. What is this device, or what software are you running on 192.168.0.10.. What sort of traffic is it?

If you can not arp from pfsense, for this 192.168.0.10 address - then no your never going to be able to send it traffic.. To do anything with..

From the out side I have 4 NAT rules to direct the trafic to 192.168.0.10

Can you post those, so we can maybe glean some insight into what your trying to do exactly.

DaddyGo

@hsv said in Multicast:

loadbalancer (MS)

it could be something like that if we go after it better:

https://docs.microsoft.com/en-us/windows-server/networking/technologies/network-load-balancing

hsv

Hi
Yes the diagram is correct, but I only have 4 WAN, but I guess the problem will be the same.

And yes pfsense can not resolve it to a MAC adresse.
Why I do not know.

I have no problem on a windows client make arp -a and see the mac address to be:
03-bf-c0-a8-0b-e1

Regards
Henning

johnpoz

If pfsense can not arp then you have a connectivity issue..

How do you have this actually connected to pfsense.

If what your trying to do is the above, that has ZERO to do with multicast and pfsense.. What you loadbalancer does with unicast your traffic coming from the internet has nothing to do with pfsense talking to the LB..

You need to figure out what the problem is with basic connectivity from pfsense 192.168.0.1 and this IP at 192.168.0.10 which is your LB.. If pfsense can not even arp for that IP then they are not actually connected via the same L2 network, ie switch cable plugged into pfsense port?

How is 192.168.0.10 connected to this 192.168.0 network?

Now if this 192.168.0.10 is some sort of VIP? If pfsense can not arp for that IP, then it is impossible for it to send it traffic If your saying its just not arping - then setup a static arp entry for it on pfsense.. this 03-bf-c0-a8-0b-e1 mac

But there should be unicast mac for your cluster.. Why can you not use that?

Some details of how you have everything connected will help us help you.

hsv

Hi

How do I add a static arp to the arp list?

The setup is 3 virtual host where pfsense and a test windows server is placed on ESXi0 on ESXi1 and 2 the mail setup are running.
From the test server I can ping and resolve the LB but on Pfsense I cannot.

So the network is working. I have for testing setup the Windows Test server with VLAN also so looked from VMware the 2 server are setup the same way.

Regards
Henning

DaddyGo

@hsv said in Multicast:

es the diagram is correct,

I used to deal with MS load balancer (especially multicast), long time ago...
(we always use a hardware base load balancer, HA proxy )

but I am interested in this topic...

no this will not work under pfSense.... (100%)
bring the theme under linux...

https://github.com/google/seesaw

hsv

Hi
I have also come to the same conclusion that multicast and Pfsense is not the way to go, and start to setup HAProxy.

But thanks for you suggestions.

Regards
Henning

DaddyGo

@hsv said in Multicast:

Pfsense is not the way to go, and start to setup HAProxy.

it took me a long time to understand what do you mean by original post, I apologize
just the way, it works...HA proxy

+++edit:
@hsv "but I only have 4 WAN, but I guess the problem will be the same."

this does not matter

n3xus_x3

@daddygo do you have any tutorial on how I can configure Multicast? I have CISCO SG300 with 2 Vlan
thanks