Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    Does someone have Netgate SG-2100 internal slot?

    Scheduled Pinned Locked Moved Hardware
    33 Posts 2 Posters 2.4k Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • D
      doronl15
      last edited by

      I want to add wireless cards and there are two slots, one like m.2 and another one thinner.
      Can I add a RT3090 wifi card to it?

      Doron

      1 Reply Last reply Reply Quote 0
      • stephenw10S
        stephenw10 Netgate Administrator
        last edited by

        It has an m.2 slot wired for SATA or USB2 with the SIM card slot connected to it. And it has an mPCIe slot wired for PCIe only.
        The PCIe slot has limited compatibility but may work with that card. If you have the card try it.
        It does work with a Compex WLE200NX so if you're buying something specifically for this get that.

        Steve

        D 1 Reply Last reply Reply Quote 0
        • D
          doronl15 @stephenw10
          last edited by

          @stephenw10
          Thanks, I ordered an atheros card with AR9280 and this is what the WLE200NX has.
          Strange, this card work ok with x86 system with pfsense 3.4.5 so I guessed it would also work here. But maybe be because its arm based system not all drivers are available.

          Doron

          D 1 Reply Last reply Reply Quote 0
          • D
            doronl15 @doronl15
            last edited by

            @doronl15
            Hi Steve,
            According to netgate documentation the intel card should work.
            However need to update the Intel acknowledgment.
            How do I edit the /boot/configuration file?
            I'm new in psfense never had to change anything in the environment.

            Doron.

            1 Reply Last reply Reply Quote 0
            • stephenw10S
              stephenw10 Netgate Administrator
              last edited by stephenw10

              To add custom loader variables create the file /boot/loader.conf.local and add them there.
              However you do not need to ack those to use them.

              The PCI driver for the SG-2100 (and SG-1100) is still in active development so some devices may not be recognised regardless of the drivers for those devices. Check the output of pciconf -lv to see if the card is seen on the bus at all.

              I have specifically tested the WLE200NX and know it works, others may not.

              Also bare in mind there are some wifi cards that are mPCIe format but are actually connected using USB. Those will never work as the slot is not wired for USB.

              Steve

              D 1 Reply Last reply Reply Quote 0
              • D
                doronl15 @stephenw10
                last edited by

                Hi Steve,
                Run the commands its recognized on the pcie as RT3090 wifi card, category network.
                However can not add it in the interface assign wireless.

                Doron.

                1 Reply Last reply Reply Quote 0
                • stephenw10S
                  stephenw10 Netgate Administrator
                  last edited by

                  Oh, nice! So it shows as a 'none' device? What are the PCI IDs shown?

                  Hmm, I thought that would be supported but it looks like it might be ral(4) only. And that is not in the 2.4.5 arm64 kernel it appears...

                  Steve

                  1 Reply Last reply Reply Quote 0
                  • D
                    doronl15
                    last edited by

                    Hi Steve,
                    here is the complete snapshot of the command prompt
                    8f2350db-983e-41e3-8afc-9c5eccf560ec-image.png
                    hope it will help, it works well with x86 HP T610 pc with pfSense 3.4.5

                    1 Reply Last reply Reply Quote 0
                    • stephenw10S
                      stephenw10 Netgate Administrator
                      last edited by

                      Yeah, that device requires the ral driver:
                      https://github.com/pfsense/FreeBSD-src/blob/RELENG_2_4_5/sys/dev/ral/if_ral_pci.c#L90

                      It's not in the pfSense 2.4.5 arm64 kernel currently. I created a feature request for it:
                      https://redmine.pfsense.org/issues/10934

                      Steve

                      1 Reply Last reply Reply Quote 0
                      • stephenw10S
                        stephenw10 Netgate Administrator
                        last edited by

                        Could you add that pciconf output as text here so I can add it? Or you can add it there yourself.

                        The other useful output there is to reboot the SG-2100 and interrrupt uboot to reach the Marvell> prompt. Then at that prompt run: pci long

                        That will give a bunch of PCI infor about the card that could be useful for debugging the PCI driver.
                        For example the WLE200NX looks like:

                        Marvell>> pci long
Scanning PCI devices on bus 0

Found PCI device 00.00.00:
  vendor ID =                   0x168c
  device ID =                   0x002a
  command register ID =         0x0006
  status register =             0x0010
  revision ID =                 0x01
  class code =                  0x02 (Network controller)
  sub class code =              0x80
  programming interface =       0x00
  cache line =                  0x08
  latency time =                0x00
  header type =                 0x00
  BIST =                        0x00
  base address 0 =              0xe8000004
  base address 1 =              0x00000000
  base address 2 =              0x00000000
  base address 3 =              0x00000000
  base address 4 =              0x00000000
  base address 5 =              0x00000000
  cardBus CIS pointer =         0x00000000
  sub system vendor ID =        0x168c
  sub system ID =               0x3099
  expansion ROM base address =  0x00000000
  interrupt line =              0xff
  interrupt pin =               0x01
  min Grant =                   0x00
  max Latency =                 0x00

                        Steve

                        1 Reply Last reply Reply Quote 0
                        • stephenw10S
                          stephenw10 Netgate Administrator
                          last edited by

                          What actual card is that you have? I'll grab one to test with if I can.

                          1 Reply Last reply Reply Quote 0
                          • D
                            doronl15
                            last edited by stephenw10

                            Hi Steve,
                            some bad news, i wanted to restore a backup from the T610 to the SG-2100 and now the SG-2100 is completely stuck.
                            its going all the way until it say "bootup complete" then the terminal is stuck.
                            how do i flash new fw? or do factory defaults without terminal?

                            TIM-1.0
WTMI-devel-1.0.0-1115f12
WTMI: system early-init
SVC REV: 5, CPU VDD voltage: 1.225V
NOTICE:  Booting Trusted Firmware
NOTICE:  BL1: v1.5(release):ROGUE2-01.00.00.01-cpu1_2G-0-g06b570a8d (Marvell-release-1.3.0)
NOTICE:  BL1: Built : 14:34:11, Feb  7 2020
NOTICE:  BL1: Booting BL2
NOTICE:  BL2: v1.5(release):ROGUE2-01.00.00.01-cpu1_2G-0-g06b570a8d (Marvell-release-1.3.0)
NOTICE:  BL2: Built : 14:34:13, Feb  7 2020
NOTICE:  BL1: Booting BL31
NOTICE:  BL31: v1.5(release):ROGUE2-01.00.00.01-cpu1_2G-0-g06b570a8d (Marvell-release-1.3.0)
NOTICE:  BL31: Built : 14

U-Boot 2018.03-devel-1.2.0ROGUE2-01.00.00.02+ (Feb 07 2020 - 14:33:22 -0500)

Model: Silicom Rogue-2
       CPU     1200 [MHz]
       L2      800 [MHz]
       TClock  200 [MHz]
       DDR     750 [MHz]
DRAM:  3.4 GiB
Comphy chip #0:
Comphy-0: SGMII1        3.125 Gbps
Comphy-1: PEX0          2.5 Gbps  
Comphy-2: SATA0         6 Gbps    
PCIE-0: Link down
MMC:   sdhci@d8000: 0
Loading Environment from SPI Flash... mvebu_spi_ofdata_to_platdata: ofdata clock 200000000, frequency 20000000
SF: Detected w25q32bv with page size 256 Bytes, erase size 4 KiB, total 4 MiB
OK
Model: Silicom Rogue-2
Net:   eth0: neta@30000 [PRIME], eth1: neta@40000
Hit any key to stop autoboot:  0 
Setting bus to 1
    13323   armada-3720-sg1100.dtb
    13535   armada-3720-sg2100.dtb

2 file(s), 0 dir(s)

13535 bytes read in 9 ms (1.4 MiB/s)
393216 bytes read in 21 ms (17.9 MiB/s)
## Starting EFI application at 01000000 ...
anning disk sdhci@d8000.blk...
Found 4 disks

>> FreeBSD EFI boot block
   Loader path: /boot/loader.efi

   Initializing modules: ZFS UFS
   Load Path: /\efi\boot\bootaa64.efi
   Load Device: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/eMMC(0)/eMMC(0)/HD(1,0x01,0,0x1,0x640)
   Probing 4 block devices......* done
    ZFS found no pools
    UFS found 1 partition
    command args: -S115200

Consoles: EFI console  

FreeBSD/arm64 EFI loader, Revision 1.1

(Thu Feb 13 14:48:37 EST 2020 root@buildbot3-nyi.netgate.com)



   Command line arguments: loader.efi -S115200

   EFI version: 2.70

   EFI Firmware: Das U-Boot (rev 0.00)

   Load Device: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/eMMC(0)/eMMC(0)/HD(3,0x01,0,0x117bd,0xe7f6c3)

   BootCurrent: 0000

   BootOrder: 532d 3131 3235 3030 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*]

Trying ESP: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/eMMC(0)/eMMC(0)/HD(3,0x01,0,0x117bd,0xe7f6c3)

Setting currdev to disk0p3:

Loading /boot/defaults/loader.conf

/boot/kernel/kernel text=0x9825b0 data=0x10ce970+0x3c7fa4 syms=[0x8+0x11f328+0x8+0xf63f3]



Hit [Enter] to boot immediately, or any other key for command prompt.


Booting [/boot/kernel/kernel] in 2 seconds... 
Booting [/boot/kernel/kernel] in 1 second... 
Booting [/boot/kernel/kernel]...               

Using DTB provided by EFI at 0x8000000.

Copyright (c) 1992-2020 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.3-STABLE #239 885b1ed26b6(factory-RELENG_2_4_5): Tue Jun  2 17:47:00 EDT 2020
    root@buildbot3-nyi.netgate.com:/build/factory-crossbuild-245-aarch64/obj/aarch64/Og10eFss/build/factory-crossbuild-245-aarch64/sources/FreeBSD-src/sys/pfSense arm64
FreeBSD clang version 8.0.1 (tags/RELEASE_801/final 366581) (based on LLVM 8.0.1)
VT: init without driver.
Starting CPU 1 (1)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffff0000001738b0, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffff00000017395c, 0) error 1
iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_bss_fw, 0xffff000000173a08, 0) error 1
iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffff000000173ab4, 0) error 1
iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffff000000173b60, 0) error 1
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xffff000000173804, 0) error 1
wlan: mac acl policy registered
random: entropy device external interface
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
simplebus1: <Flattened device tree simple bus> on simplebus0
pinctl0: <Armada 37x0 North Bridge pinctl Controller> mem 0x13800-0x138ff,0x13c00-0x13c1f on simplebus1
gpio0: <Armada 37x0 GPIO Controller> on pinctl0
gpiobus0: <OFW GPIO bus> on gpio0
pinctl1: <Armada 37x0 South Bridge pinctl Controller> mem 0x18800-0x188ff,0x18c00-0x18c1f on simplebus1
gpio1: <Armada 37x0 GPIO Controller> on pinctl1
gpiobus1: <OFW GPIO bus> on gpio1
gpiomdio0: <GPIO MDIO Bus bit-banging driver> at pins 21,23 on gpiobus1
gpiomdio0: MDC pin: 21, MDIO pin: 23
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
gic0: <ARM Generic Interrupt Controller v3.0> mem 0x1d00000-0x1d0ffff,0x1d40000-0x1d7ffff,0x1d80000-0x1d81fff,0x1d90000-0x1d91fff,0x1da0000-0x1dbffff irq 27 on simplebus1
generic_timer0: <ARMv8 Generic Timer> irq 0,1,2,3 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 12500000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 12500000 Hz quality 1000
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
cpu1: <Open Firmware CPU> on cpulist0
pmu0: <Performance Monitoring Unit> irq 4 on ofwbus0
spi0: <Armada 37x0 SPI controller> mem 0x10600-0x10fff irq 6 on simplebus1
iichb0: <Marvell Armada 37x0 IIC controller> mem 0x11000-0x11023 irq 7 on simplebus1
iicbus0: <OFW I2C bus> on iichb0
iic0: <I2C generic I/O> on iicbus0
iichb1: <Marvell Armada 37x0 IIC controller> mem 0x11080-0x110a3 irq 8 on simplebus1
iicbus1: <OFW I2C bus> on iichb1
iic1: <I2C generic I/O> on iicbus1
nxprtc0: <NXP PCF8563 RTC> at addr 0xa2 on iicbus1
gpio2: <ISSI IS31FL3199 9 channel light effect LED driver> at addr 0xce on iicbus1
gpiobus2: <OFW GPIO bus> on gpio2
gpioc2: <GPIO controller> on gpio2
uart0: <Marvell Armada 3700 UART> mem 0x12000-0x121ff irq 9,10,11 on simplebus1
uart0: console (115200,n,8,1)
gpioc0: <GPIO controller> on gpio0
gpioc1: <GPIO controller> on gpio1
mvneta0: <NETA controller> mem 0x30000-0x33fff irq 14 on simplebus1
mvneta0: version is 10
mvneta0: Ethernet address: 00:e0:ed:be:ca:24
miibus0: <MII bus> on gpiomdio0
mv88e151x0: <Marvell 88E1512 Gigabit PHY> PHY 1 on miibus0
mv88e151x0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseSX, 1000baseSX-FDX, auto
mvneta1: <NETA controller> mem 0x40000-0x43fff irq 15 on simplebus1
mvneta1: version is 10
mvneta1: Ethernet address: 00:e0:ed:be:ca:25
mdio0: <MDIO> on mvneta1
e6000sw0: <Marvell 88E6141> on mdio0
e6000sw0: single-chip addressing mode
e6000sw0: PHY at port 1
miibus1: <MII bus> on e6000sw0
e1000phy0: <Marvell 88E1000 Gigabit PHY> PHY 17 on miibus1
e1000phy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: PHY at port 2
miibus2: <MII bus> on e6000sw0
e1000phy1: <Marvell 88E1000 Gigabit PHY> PHY 18 on miibus2
e1000phy1:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: PHY at port 3
miibus3: <MII bus> on e6000sw0
e1000phy2: <Marvell 88E1000 Gigabit PHY> PHY 19 on miibus3
e1000phy2:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: PHY at port 4
miibus4: <MII bus> on e6000sw0
e1000phy3: <Marvell 88E1000 Gigabit PHY> PHY 20 on miibus4
e1000phy3:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: CPU port at 5
e6000sw0: fixed port at 5
e6000sw0: switch is ready.
etherswitch0: <Switch controller> on e6000sw0
xhci0: <Marvell Integrated USB 3.0 controller> mem 0x58000-0x5bfff irq 16 on simplebus1
xhci0: 32 bytes context size, 32-bit DMA
usbus0 on xhci0
ehci0: <Marvell Integrated USB 2.0 controller> mem 0x5e000-0x5ffff irq 17 on simplebus1
usbus1: EHCI version 1.0
usbus1 on ehci0
sdhci_xenon0: <Armada Xenon SDHCI controller> mem 0xd8000-0xd82ff,0x17808-0x1780b irq 25 on simplebus1
mmc0: <MMC/SD bus> on sdhci_xenon0
ahci0: <AHCI SATA controller> mem 0xe0000-0xe1fff irq 26 on simplebus1
ahci0: AHCI v1.30 with 1 6Gbps ports, Port Multiplier supported with FBS
ahcich0: <AHCI channel> at channel 0 on ahci0
pcib0: <Marvell Armada 3700 PCIe Bus Controller> mem 0xd0070000-0xd008ffff irq 5 on simplebus0
pcib0: link never came up
pci0: <PCI bus> on pcib0
cryptosoft0: <software crypto>
Timecounters tick every 1.000 msec
mvneta1: link state changed to UP
spibus0: <OFW SPI bus> on spi0
mx25l0: <M25Pxx Flash Family> at cs 0 mode 0 on spibus0
mx25l0: device type w25q32, size 4096K in 64 sectors of 64K, erase size 4K
nxprtc0: registered as a time-of-day clock, resolution 0.015625s
e6000sw0port1: link state changed to DOWN
e6000sw0port2: link state changed to DOWN
e6000sw0port3: link state changed to DOWN
e6000sw0port4: link state changed to DOWN
usbus0: 5.0Gbps Super Speed USB v3.0
usbus1: 480Mbps High Speed USB v2.0
ugen0.1: <Marvell XHCI root HUB> at usbus0
uhub0: <Marvell XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
ugen1.1: <Marvell EHCI root HUB> at usbus1
uhub1: <Marvell EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
mmcsd0: 8GB <MMCHC DG4008 0.1 SN 64F2B610 MFG 12/2019 by 69 0x0000> at mmc0 50.0MHz/8bit/65535-block
mmcsd0boot0: 4MB partion 1 at mmcsd0
mmcsd0boot1: 4MB partion 2 at mmcsd0
mmcsd0rpmb: 4MB partion 3 at mmcsd0
uhub0: 2 ports with 2 removable, self powered
uhub1: 1 port with 1 removable, self powered
Release APs
CPU  0: ARM Cortex-A53 r0p4 affinity:  0
 Instruction Set Attributes 0 = <AES+PMULL,SHA1,SHA2,CRC32>
 Instruction Set Attributes 1 = <>
         Processor Features 0 = <GIC,AdvSIMD,Float,EL3 32,EL2 32,EL1 32,EL0 32>
         Processor Features 1 = <0>
      Memory Model Features 0 = <4k Granule,64k Granule,MixedEndian,S/NS Mem,16bit ASID,1TB PA>
      Memory Model Features 1 = <>
      Memory Model Features 2 = <32b CCIDX,48b VA>
             Debug Features 0 = <2 CTX Breakpoints,4 Watchpoints,6 Breakpoints,PMUv3,Debug v8>
             Debug Features 1 = <0>
         Auxiliary Features 0 = <0>
         Auxiliary Features 1 = <0>
CPU  1: ARM Cortex-A53 r0p4 affinity:  1
Trying to mount root from ufs:/dev/ufsid/5ed6cabbfa4b9f89 [rw,noatime]...
WARNING: / was not properly dismounted
Configuring crash dumps...
No suitable dump device was found.
** SU+J Recovering /dev/ufsid/5ed6cabbfa4b9f89
** Reading 11730944 byte journal from inode 4.
** Building recovery table.
** Resolving unreferenced inode list.
** Processing journal entries.
** 255 journal records in 37376 bytes for 21.83% utilization
** Freed 6 inodes (0 dirs) 4 blocks, and 4 frags.

***** FILE SYSTEM MARKED CLEAN *****
Filesystems are clean, continuing...
Mounting filesystems...
random: unblocking device.

        __
 _ __  / _|___  ___ _ __  ___  ___
| '_ \| |_/ __|/ _ \ '_ \/ __|/ _ \
| |_) |  _\__ \  __/ | | \__ \  __/
| .__/|_| |___/\___|_| |_|___/\___|
|_|


Welcome to pfSense 2.4.5-RELEASE (Patch 1)...

...ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib /usr/lib/engines /usr/local/lib /usr/local/lib/ipsec /usr/local/lib/perl5/5.30/mach/CORE
done.
>>> Removing vital flag from php72... done.
External config loader 1.0 is now starting... mmcsd0s1 mmcsd0s2 mmcsd0s3
Launching the init system......... done.
Initializing.................. done.
Starting device manager (devd)...done.
Loading configuration......done.
Updating configuration...done.
Checking config backups consistency.......................done.
Setting up extended sysctls...done.
Setting timezone...done.
Configuring loopback interface...lo0: link state changed to UP
done.
Starting syslog...done.
Starting Secure Shell Services...done.
Configuring switch...done.
Setting up interfaces microcode...done.
Configuring loopback interface...done.
Creating wireless clone interfaces...done.
Configuring LAGG interfaces...done.
Configuring VLAN interfaces...done.
Configuring QinQ interfaces...done.
Configuring IPsec VTI interfaces...done.
Configuring WAN interface...done.
Configuring LAN interface...done.
Configuring WLAN interface...ifconfig: interface ral0_wlan0 does not exist
done.
Configuring MYSWITCH interface...done.
Configuring CARP settings...done.
Syncing OpenVPN settings...done.
Configuring firewall......done.
Starting PFLOG...done.
Setting up gateway monitors...done.
Setting up static routes...route: writing to routing socket: Network is unreachable
route: route has not been found
done.
Setting up DNSs...
Starting DNS Resolver...done.
Synchronizing user settings...done.
Starting webConfigurator...done.
Configuring CRON...done.
Starting NTP time client...done.
Starting DHCP service...done.
Configuring firewall......done.
Generating RRD graphs...done.
Starting syslog...done.
Starting CRON... done.
pfSense 2.4.5-RELEASE (Patch 1) arm64 Tue Jun 02 17:44:41 EDT 2020
Bootup complete
                            1 Reply Last reply Reply Quote 0
                            • D
                              doronl15
                              last edited by

                              Hi Steve,
                              the reset button does not work, however in LAN1 i've succeeded to get the GUI and restored the configuration.
                              So we are back in square 1
                              here is photo of the Ralink3090
                              2823295c-305b-475a-8571-5224108fd2ff-image.png

                              1 Reply Last reply Reply Quote 0
                              • stephenw10S
                                stephenw10 Netgate Administrator
                                last edited by

                                I'll see if I can grab get one.

                                The config you restored probably had the wrong console type setup would be my first guess. You could probably have just enabled the serial console in the gui in Sys > Adv > Admin Access.

                                Steve

                                1 Reply Last reply Reply Quote 0
                                • stephenw10S
                                  stephenw10 Netgate Administrator
                                  last edited by

                                  The ral(4) driver is now in 2.5 snapshots for the SG-2100:

                                  [2.5.0-DEVELOPMENT][admin@2100-2.stevew.lan]/root: kldstat -v | grep /ral
		163 pci/ral

                                  Steve

                                  1 Reply Last reply Reply Quote 0
                                  • stephenw10S
                                    stephenw10 Netgate Administrator
                                    last edited by

                                    I acquired a card that uses this driver, it appears to be detected and driver loads:

                                    [2.5.0-DEVELOPMENT][root@2100-2.stevew.lan]/root: pciconf -lv
ral0@pci0:0:0:0:        class=0x028000 card=0x27901814 chip=0x07811814 rev=0x00 hdr=0x00
    vendor     = 'Ralink corp.'
    device     = 'RT2790 Wireless 802.11n 1T/2R PCIe'
    class      = network
                                    1 Reply Last reply Reply Quote 0
                                    • D
                                      doronl15
                                      last edited by

                                      Is this in 2.5.0 beta?
                                      Since its not released yet.

                                      1 Reply Last reply Reply Quote 0
                                      • stephenw10S
                                        stephenw10 Netgate Administrator
                                        last edited by

                                        It is in current 2.5 snaps yes.

                                        That particular card just causes a panic when I try to configure it so if you can test something else that would be great.

                                        Steve

                                        1 Reply Last reply Reply Quote 0
                                        • D
                                          doronl15
                                          last edited by

                                          Bad news.
                                          I've tried to update to latest 2.5.0 developments snapshot and now the system won't boot and stuck in the Marvell UBOOT with bad CRC.
                                          What can I do to recover?

                                          Doron.

                                          1 Reply Last reply Reply Quote 0
                                          • stephenw10S
                                            stephenw10 Netgate Administrator
                                            last edited by

                                            Bad crc might just be because it tried to boot from something that doesn't exist.

                                            Open a ticket with us and get the restore image if it's unbootable: https://go.netgate.com/

                                            Steve

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.