How does IPv6 negotiation over IPv4's PPPoE work?

senseivita

I'm seriously not kidding, I thought it was silly too, here's from Wikipedia:

"For example, PPPoEoE, when the transport is Ethernet itself, as in the case of Metro Ethernet networks. (In this notation, the original use of PPPoE would be labeled PPPoEoA, although it should not be confused with PPPoA, which is a different encapsulation protocol.)"

It's in the first section. I saw it first on one of these Cisco Academy sites, for the CCNA and all the other CC-something tests they do.

That *oA thing was a staple in the xDSL modems, ATM. It's supposed to be super old but still held up until recently even competing with fiber. There was something that made it good for huge deployments, like an ISP's DSL infra but I forgot what it was.

@Hikari you're right, when my connection happens to drop, which is when I restart the firewall every leap year, sometimes I'd get it back. The IPv4 one, the IPv6 block is so large I can't memorize further than the first two digits, "28", considering they hand a /64 I'm still 14 digits short.

To check I'd have to go to one of these IPv6 test sites bc the firewall reports only a link-local address. Thanks but I'll pass, I'm fine too with the /48 from Hurricane Electric, even if it's got slightly higher ping time. 2ms is nothing anyway.

senseivita

"PPPoEoE is a variant of PPPoE where the Layer 2 transport protocol is now Ethernet or 802.1q VLAN
instead of ATM. This encapsulation method is generally found in Metro Ethernet or Ethernet digital
subscriber line access multiplexer (DSLAM) environments. The common deployment model is that this
encapsulation method is typically found in multi-tenant buildings or hotels. By delivering Ethernet to
the subscriber, the available bandwidth is much more abundant and the ease of further service delivery
is increased."

Understanding Broadband Access Aggregation (year 2005, ouch)
https://www.cisco.com/en/US/docs/ios/bbdsl/configuration/guide/bba_understanding.pdf

Catalyst 4500 Series Switch Software Configuration Guide, 12.2(54)SG
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/12-2/54sg/configuration/guide/config/PPPoE.html

I'm such a huge nerd that this gets me excited. I blame pfSense though, before I switched to it a few years ago three tops (the ugly red UI was already gone), I couldn't care less about networking...maybe VPNs for region blocks but that's it.

JKnott

@skilledinept said in How does IPv6 negotiation over IPv4's PPPoE work?:

"For example, PPPoEoE, when the transport is Ethernet itself, as in the case of Metro Ethernet networks. (In this notation, the original use of PPPoE would be labeled PPPoEoA, although it should not be confused with PPPoA, which is a different encapsulation protocol.)"

As one who has worked with providing fibre connections to businesses and data centres, I can tell you that would be either VLANs or MPLS. I have worked with VLAN on VLAN (QinQ) many times, though not MPLS.

The difference between PPPoE & PPPoA is the underlying tech. Many years ago, the phone companies had the big idea that ATM would take over the world, but IP beat them to it. ATM was part of the synchronous telecom network, but even that network is disappearing. BTW, I spent many years working for a major telecom company and in the last 5 years there, my job was planning the installation of telecom equipment in the central office and customer sites, so I have an excellent understanding of the various technologies.

While Wikipedia is an excellent reference, it's not infallible. There have been a few times when I have provided corrections to it.

JKnott

@skilledinept

I'm the opposite. Almost my entire career has been about telecom, computers and networks. I spent 23 years at a telecom company, 17.5 as a tech and 5.5 in planning. I was also doing software support at IBM for almost 4 years. Over the years, I have worked with a wide variety of technology, some long obsolete, and always trying to learn more.

Hikari

@skilledinept said in How does IPv6 negotiation over IPv4's PPPoE work?:

@Hikari you're right, when my connection happens to drop, which is when I restart the firewall every leap year, sometimes I'd get it back. The IPv4 one, the IPv6 block is so large I can't memorize further than the first two digits, "28", considering they hand a /64 I'm still 14 digits short.

Me too. When I got my OpenWRT I was developing a few monitoring tools to help me know when any ISP goes offline and when IP is changed. I wanted to make a report to show how often IP changes.

But my battle with ISPs for proper IPv6 support and lack of knowledge on Bash made me tired and I stopped.

JKnott

@Hikari

Several years ago, when I had an intermittent problem, I wrote a bash script to ping the ISP's gateway and record the failures. There wasn't much to it.

#! /bin/sh
while [ 1 ]
do
ping <target> -4 -c 1 || date >> ~/log;sleep 50
done

This should work with IPv6 as well as IPv4.

Hikari

tnx!

In last few years I'm using a public service that receives an HTTP request and reports if it was received.

What I've been considering is developing a PHP app to receive data on GET request and record on Postgres. Then it's just a matter of querying it and building charts.

I also developed a Bash code that queries SpeedTest and receives some nice data back, I might do the same with it.

I also wish to run it on my server instead of on router and use some failover filter to somehow force each request to pass on specific WAN, so that I can properly test if LAN has connectivity. But it takes a lot of time doing tests of plugging and unplugging WAN cables to assure, and of course learn how to do these filters.

JKnott

@Hikari said in How does IPv6 negotiation over IPv4's PPPoE work?:

I also wish to run it on my server instead of on router

That would rule out using the IPv6 gateway, if it uses a link local address.

Hikari

That's another challenge, do load balancing on IPv6 where router manages it and chooses what route connections will use.

If that works and I'm able in example to rule a given destination to always use a given WAN, it must work.

senseivita

What if you use a remote receiver?

From experience I've learned that DDNS in pfSense, or any other appliance only works when you're "gentle" to it, meaning one hostname. As soon as you add additional hostnames, domains it'll fail to update them so I got a VPS and installed pfSense on it for the static IP they give you, starting at USD5/mo, sometimes less, it's the cheapest static address you can rent.

I actually use it for the GIF to HurricaneElectric and tunnel both IPv4 and IPv6 to the local pfSense, I have about the same latency in local IPv4 as in tunneled IPv4 and (double-) tunneled IPv6.

But where I'm going with this is:

I also use my remote instance's public address as the monitor IP for the local WAN gateway. And since I can contact the remote instance locally through the tunnel, I get statistics on it with any tool, like from which IP a tunnel is has been brought up--which I know would only be mine. "Loopback" Stats. This data can be sent to a syslog server or queried through SNMP. You can query all sorts of data, I check consumption because the VPS has a data cap, I'm used to not having it because of my ISP so this is really handy, you can set it to notify you through a bot on Telegram, Matrix, classic email or a buttload of other integrations it has:

The first one is LibreNMS, completely free, does SNMP and syslog, you don't need scripts or databases because it's meant to keep historic data, it's all there as long as you feed it. The second one is VMware's vRealize Log Insight, also free (*with purchase) it only does syslog but it's very comprehensive, king of syslogs, it can proxy the syslog to yet more servers and has this thing called agents, custom-made-on-site apps preconfigured to send data to it and reconfigurable remotely. It's very cool.

LibreNMS is like a 2core/2G/20G VM if I'm not mistaken, Log Insight is much hungrier but you can tweak it before first starting it, I discovered. Both need fast disks.