Does someone have Netgate SG-2100 internal slot?
-
Hi Steve,
some bad news, i wanted to restore a backup from the T610 to the SG-2100 and now the SG-2100 is completely stuck.
its going all the way until it say "bootup complete" then the terminal is stuck.
how do i flash new fw? or do factory defaults without terminal?TIM-1.0 WTMI-devel-1.0.0-1115f12 WTMI: system early-init SVC REV: 5, CPU VDD voltage: 1.225V NOTICE: Booting Trusted Firmware NOTICE: BL1: v1.5(release):ROGUE2-01.00.00.01-cpu1_2G-0-g06b570a8d (Marvell-release-1.3.0) NOTICE: BL1: Built : 14:34:11, Feb 7 2020 NOTICE: BL1: Booting BL2 NOTICE: BL2: v1.5(release):ROGUE2-01.00.00.01-cpu1_2G-0-g06b570a8d (Marvell-release-1.3.0) NOTICE: BL2: Built : 14:34:13, Feb 7 2020 NOTICE: BL1: Booting BL31 NOTICE: BL31: v1.5(release):ROGUE2-01.00.00.01-cpu1_2G-0-g06b570a8d (Marvell-release-1.3.0) NOTICE: BL31: Built : 14 U-Boot 2018.03-devel-1.2.0ROGUE2-01.00.00.02+ (Feb 07 2020 - 14:33:22 -0500) Model: Silicom Rogue-2 CPU 1200 [MHz] L2 800 [MHz] TClock 200 [MHz] DDR 750 [MHz] DRAM: 3.4 GiB Comphy chip #0: Comphy-0: SGMII1 3.125 Gbps Comphy-1: PEX0 2.5 Gbps Comphy-2: SATA0 6 Gbps PCIE-0: Link down MMC: sdhci@d8000: 0 Loading Environment from SPI Flash... mvebu_spi_ofdata_to_platdata: ofdata clock 200000000, frequency 20000000 SF: Detected w25q32bv with page size 256 Bytes, erase size 4 KiB, total 4 MiB OK Model: Silicom Rogue-2 Net: eth0: neta@30000 [PRIME], eth1: neta@40000 Hit any key to stop autoboot: 0 Setting bus to 1 13323 armada-3720-sg1100.dtb 13535 armada-3720-sg2100.dtb 2 file(s), 0 dir(s) 13535 bytes read in 9 ms (1.4 MiB/s) 393216 bytes read in 21 ms (17.9 MiB/s) ## Starting EFI application at 01000000 ... anning disk sdhci@d8000.blk... Found 4 disks >> FreeBSD EFI boot block Loader path: /boot/loader.efi Initializing modules: ZFS UFS Load Path: /\efi\boot\bootaa64.efi Load Device: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/eMMC(0)/eMMC(0)/HD(1,0x01,0,0x1,0x640) Probing 4 block devices......* done ZFS found no pools UFS found 1 partition command args: -S115200 Consoles: EFI console FreeBSD/arm64 EFI loader, Revision 1.1 (Thu Feb 13 14:48:37 EST 2020 root@buildbot3-nyi.netgate.com) Command line arguments: loader.efi -S115200 EFI version: 2.70 EFI Firmware: Das U-Boot (rev 0.00) Load Device: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/eMMC(0)/eMMC(0)/HD(3,0x01,0,0x117bd,0xe7f6c3) BootCurrent: 0000 BootOrder: 532d 3131 3235 3030 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] 0000[*] Trying ESP: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/eMMC(0)/eMMC(0)/HD(3,0x01,0,0x117bd,0xe7f6c3) Setting currdev to disk0p3: Loading /boot/defaults/loader.conf /boot/kernel/kernel text=0x9825b0 data=0x10ce970+0x3c7fa4 syms=[0x8+0x11f328+0x8+0xf63f3] Hit [Enter] to boot immediately, or any other key for command prompt. Booting [/boot/kernel/kernel] in 2 seconds... Booting [/boot/kernel/kernel] in 1 second... Booting [/boot/kernel/kernel]... Using DTB provided by EFI at 0x8000000. Copyright (c) 1992-2020 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 11.3-STABLE #239 885b1ed26b6(factory-RELENG_2_4_5): Tue Jun 2 17:47:00 EDT 2020 root@buildbot3-nyi.netgate.com:/build/factory-crossbuild-245-aarch64/obj/aarch64/Og10eFss/build/factory-crossbuild-245-aarch64/sources/FreeBSD-src/sys/pfSense arm64 FreeBSD clang version 8.0.1 (tags/RELEASE_801/final 366581) (based on LLVM 8.0.1) VT: init without driver. Starting CPU 1 (1) FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE. ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffff0000001738b0, 0) error 1 ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE. ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffff00000017395c, 0) error 1 iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE. iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (iwi_bss_fw, 0xffff000000173a08, 0) error 1 iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE. iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffff000000173ab4, 0) error 1 iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE. iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffff000000173b60, 0) error 1 ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE. ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (ipw_bss_fw, 0xffff000000173804, 0) error 1 wlan: mac acl policy registered random: entropy device external interface kbd0 at kbdmux0 ofwbus0: <Open Firmware Device Tree> simplebus0: <Flattened device tree simple bus> on ofwbus0 simplebus1: <Flattened device tree simple bus> on simplebus0 pinctl0: <Armada 37x0 North Bridge pinctl Controller> mem 0x13800-0x138ff,0x13c00-0x13c1f on simplebus1 gpio0: <Armada 37x0 GPIO Controller> on pinctl0 gpiobus0: <OFW GPIO bus> on gpio0 pinctl1: <Armada 37x0 South Bridge pinctl Controller> mem 0x18800-0x188ff,0x18c00-0x18c1f on simplebus1 gpio1: <Armada 37x0 GPIO Controller> on pinctl1 gpiobus1: <OFW GPIO bus> on gpio1 gpiomdio0: <GPIO MDIO Bus bit-banging driver> at pins 21,23 on gpiobus1 gpiomdio0: MDC pin: 21, MDIO pin: 23 psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0 gic0: <ARM Generic Interrupt Controller v3.0> mem 0x1d00000-0x1d0ffff,0x1d40000-0x1d7ffff,0x1d80000-0x1d81fff,0x1d90000-0x1d91fff,0x1da0000-0x1dbffff irq 27 on simplebus1 generic_timer0: <ARMv8 Generic Timer> irq 0,1,2,3 on ofwbus0 Timecounter "ARM MPCore Timecounter" frequency 12500000 Hz quality 1000 Event timer "ARM MPCore Eventtimer" frequency 12500000 Hz quality 1000 cpulist0: <Open Firmware CPU Group> on ofwbus0 cpu0: <Open Firmware CPU> on cpulist0 cpu1: <Open Firmware CPU> on cpulist0 pmu0: <Performance Monitoring Unit> irq 4 on ofwbus0 spi0: <Armada 37x0 SPI controller> mem 0x10600-0x10fff irq 6 on simplebus1 iichb0: <Marvell Armada 37x0 IIC controller> mem 0x11000-0x11023 irq 7 on simplebus1 iicbus0: <OFW I2C bus> on iichb0 iic0: <I2C generic I/O> on iicbus0 iichb1: <Marvell Armada 37x0 IIC controller> mem 0x11080-0x110a3 irq 8 on simplebus1 iicbus1: <OFW I2C bus> on iichb1 iic1: <I2C generic I/O> on iicbus1 nxprtc0: <NXP PCF8563 RTC> at addr 0xa2 on iicbus1 gpio2: <ISSI IS31FL3199 9 channel light effect LED driver> at addr 0xce on iicbus1 gpiobus2: <OFW GPIO bus> on gpio2 gpioc2: <GPIO controller> on gpio2 uart0: <Marvell Armada 3700 UART> mem 0x12000-0x121ff irq 9,10,11 on simplebus1 uart0: console (115200,n,8,1) gpioc0: <GPIO controller> on gpio0 gpioc1: <GPIO controller> on gpio1 mvneta0: <NETA controller> mem 0x30000-0x33fff irq 14 on simplebus1 mvneta0: version is 10 mvneta0: Ethernet address: 00:e0:ed:be:ca:24 miibus0: <MII bus> on gpiomdio0 mv88e151x0: <Marvell 88E1512 Gigabit PHY> PHY 1 on miibus0 mv88e151x0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseSX, 1000baseSX-FDX, auto mvneta1: <NETA controller> mem 0x40000-0x43fff irq 15 on simplebus1 mvneta1: version is 10 mvneta1: Ethernet address: 00:e0:ed:be:ca:25 mdio0: <MDIO> on mvneta1 e6000sw0: <Marvell 88E6141> on mdio0 e6000sw0: single-chip addressing mode e6000sw0: PHY at port 1 miibus1: <MII bus> on e6000sw0 e1000phy0: <Marvell 88E1000 Gigabit PHY> PHY 17 on miibus1 e1000phy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto e6000sw0: PHY at port 2 miibus2: <MII bus> on e6000sw0 e1000phy1: <Marvell 88E1000 Gigabit PHY> PHY 18 on miibus2 e1000phy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto e6000sw0: PHY at port 3 miibus3: <MII bus> on e6000sw0 e1000phy2: <Marvell 88E1000 Gigabit PHY> PHY 19 on miibus3 e1000phy2: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto e6000sw0: PHY at port 4 miibus4: <MII bus> on e6000sw0 e1000phy3: <Marvell 88E1000 Gigabit PHY> PHY 20 on miibus4 e1000phy3: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto e6000sw0: CPU port at 5 e6000sw0: fixed port at 5 e6000sw0: switch is ready. etherswitch0: <Switch controller> on e6000sw0 xhci0: <Marvell Integrated USB 3.0 controller> mem 0x58000-0x5bfff irq 16 on simplebus1 xhci0: 32 bytes context size, 32-bit DMA usbus0 on xhci0 ehci0: <Marvell Integrated USB 2.0 controller> mem 0x5e000-0x5ffff irq 17 on simplebus1 usbus1: EHCI version 1.0 usbus1 on ehci0 sdhci_xenon0: <Armada Xenon SDHCI controller> mem 0xd8000-0xd82ff,0x17808-0x1780b irq 25 on simplebus1 mmc0: <MMC/SD bus> on sdhci_xenon0 ahci0: <AHCI SATA controller> mem 0xe0000-0xe1fff irq 26 on simplebus1 ahci0: AHCI v1.30 with 1 6Gbps ports, Port Multiplier supported with FBS ahcich0: <AHCI channel> at channel 0 on ahci0 pcib0: <Marvell Armada 3700 PCIe Bus Controller> mem 0xd0070000-0xd008ffff irq 5 on simplebus0 pcib0: link never came up pci0: <PCI bus> on pcib0 cryptosoft0: <software crypto> Timecounters tick every 1.000 msec mvneta1: link state changed to UP spibus0: <OFW SPI bus> on spi0 mx25l0: <M25Pxx Flash Family> at cs 0 mode 0 on spibus0 mx25l0: device type w25q32, size 4096K in 64 sectors of 64K, erase size 4K nxprtc0: registered as a time-of-day clock, resolution 0.015625s e6000sw0port1: link state changed to DOWN e6000sw0port2: link state changed to DOWN e6000sw0port3: link state changed to DOWN e6000sw0port4: link state changed to DOWN usbus0: 5.0Gbps Super Speed USB v3.0 usbus1: 480Mbps High Speed USB v2.0 ugen0.1: <Marvell XHCI root HUB> at usbus0 uhub0: <Marvell XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0 ugen1.1: <Marvell EHCI root HUB> at usbus1 uhub1: <Marvell EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 mmcsd0: 8GB <MMCHC DG4008 0.1 SN 64F2B610 MFG 12/2019 by 69 0x0000> at mmc0 50.0MHz/8bit/65535-block mmcsd0boot0: 4MB partion 1 at mmcsd0 mmcsd0boot1: 4MB partion 2 at mmcsd0 mmcsd0rpmb: 4MB partion 3 at mmcsd0 uhub0: 2 ports with 2 removable, self powered uhub1: 1 port with 1 removable, self powered Release APs CPU 0: ARM Cortex-A53 r0p4 affinity: 0 Instruction Set Attributes 0 = <AES+PMULL,SHA1,SHA2,CRC32> Instruction Set Attributes 1 = <> Processor Features 0 = <GIC,AdvSIMD,Float,EL3 32,EL2 32,EL1 32,EL0 32> Processor Features 1 = <0> Memory Model Features 0 = <4k Granule,64k Granule,MixedEndian,S/NS Mem,16bit ASID,1TB PA> Memory Model Features 1 = <> Memory Model Features 2 = <32b CCIDX,48b VA> Debug Features 0 = <2 CTX Breakpoints,4 Watchpoints,6 Breakpoints,PMUv3,Debug v8> Debug Features 1 = <0> Auxiliary Features 0 = <0> Auxiliary Features 1 = <0> CPU 1: ARM Cortex-A53 r0p4 affinity: 1 Trying to mount root from ufs:/dev/ufsid/5ed6cabbfa4b9f89 [rw,noatime]... WARNING: / was not properly dismounted Configuring crash dumps... No suitable dump device was found. ** SU+J Recovering /dev/ufsid/5ed6cabbfa4b9f89 ** Reading 11730944 byte journal from inode 4. ** Building recovery table. ** Resolving unreferenced inode list. ** Processing journal entries. ** 255 journal records in 37376 bytes for 21.83% utilization ** Freed 6 inodes (0 dirs) 4 blocks, and 4 frags. ***** FILE SYSTEM MARKED CLEAN ***** Filesystems are clean, continuing... Mounting filesystems... random: unblocking device. __ _ __ / _|___ ___ _ __ ___ ___ | '_ \| |_/ __|/ _ \ '_ \/ __|/ _ \ | |_) | _\__ \ __/ | | \__ \ __/ | .__/|_| |___/\___|_| |_|___/\___| |_| Welcome to pfSense 2.4.5-RELEASE (Patch 1)... ...ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib /usr/lib/engines /usr/local/lib /usr/local/lib/ipsec /usr/local/lib/perl5/5.30/mach/CORE done. >>> Removing vital flag from php72... done. External config loader 1.0 is now starting... mmcsd0s1 mmcsd0s2 mmcsd0s3 Launching the init system......... done. Initializing.................. done. Starting device manager (devd)...done. Loading configuration......done. Updating configuration...done. Checking config backups consistency.......................done. Setting up extended sysctls...done. Setting timezone...done. Configuring loopback interface...lo0: link state changed to UP done. Starting syslog...done. Starting Secure Shell Services...done. Configuring switch...done. Setting up interfaces microcode...done. Configuring loopback interface...done. Creating wireless clone interfaces...done. Configuring LAGG interfaces...done. Configuring VLAN interfaces...done. Configuring QinQ interfaces...done. Configuring IPsec VTI interfaces...done. Configuring WAN interface...done. Configuring LAN interface...done. Configuring WLAN interface...ifconfig: interface ral0_wlan0 does not exist done. Configuring MYSWITCH interface...done. Configuring CARP settings...done. Syncing OpenVPN settings...done. Configuring firewall......done. Starting PFLOG...done. Setting up gateway monitors...done. Setting up static routes...route: writing to routing socket: Network is unreachable route: route has not been found done. Setting up DNSs... Starting DNS Resolver...done. Synchronizing user settings...done. Starting webConfigurator...done. Configuring CRON...done. Starting NTP time client...done. Starting DHCP service...done. Configuring firewall......done. Generating RRD graphs...done. Starting syslog...done. Starting CRON... done. pfSense 2.4.5-RELEASE (Patch 1) arm64 Tue Jun 02 17:44:41 EDT 2020 Bootup complete -
Hi Steve,
the reset button does not work, however in LAN1 i've succeeded to get the GUI and restored the configuration.
So we are back in square 1
here is photo of the Ralink3090
-
I'll see if I can grab get one.
The config you restored probably had the wrong console type setup would be my first guess. You could probably have just enabled the serial console in the gui in Sys > Adv > Admin Access.
Steve
-
The ral(4) driver is now in 2.5 snapshots for the SG-2100:
[2.5.0-DEVELOPMENT][admin@2100-2.stevew.lan]/root: kldstat -v | grep /ral 163 pci/ralSteve
-
I acquired a card that uses this driver, it appears to be detected and driver loads:
[2.5.0-DEVELOPMENT][root@2100-2.stevew.lan]/root: pciconf -lv ral0@pci0:0:0:0: class=0x028000 card=0x27901814 chip=0x07811814 rev=0x00 hdr=0x00 vendor = 'Ralink corp.' device = 'RT2790 Wireless 802.11n 1T/2R PCIe' class = network -
Is this in 2.5.0 beta?
Since its not released yet. -
It is in current 2.5 snaps yes.
That particular card just causes a panic when I try to configure it so if you can test something else that would be great.
Steve
-
Bad news.
I've tried to update to latest 2.5.0 developments snapshot and now the system won't boot and stuck in the Marvell UBOOT with bad CRC.
What can I do to recover?Doron.
-
Bad crc might just be because it tried to boot from something that doesn't exist.
Open a ticket with us and get the restore image if it's unbootable: https://go.netgate.com/
Steve
-
I've opened a ticket.
Thanks. -
The kernel panic here is now resolved. However the particular card I have does not work. Needs more testing with different hardware:
https://redmine.pfsense.org/issues/11021Steve
-
@stephenw10 Hi,
i've got my SG2100 back after RMA procedure...
However, i'm now afraid to do the move to 2.5.0 Beta from the GUI.
do you have a site where i can download an iso image of aarch64 2.5.0?Doron.
-
@doronl15 Hi Stepen,
It happened again :(
I upgraded from 2.4.5_1 to 2.5.0 DEVEL via the web gui and again the system stop booting in uboot stage.
Do you happen to have an iso image so I can try to upgrade from USB stick?Doron
-
Let me see what I can do.
There is a know issue upgrading right now but if you replace the uboot envs, as I assume you did before, it will boot correctly and continue into the 2.5 upgrade. I just did exactly that on a test device here.
Steve
-
@stephenw10 Hi,
Are you sure if I fix uboot environment it will boot to 2.5?
Can you please send me the correct uboot environment parameter to change? -
These are the commands I used to restore the correct uboot envs from the default values you will have now:
setenv boot_file efi/boot/bootaa64.efi setenv bootcmd 'run setLED; run mmcboot; run scsiboot; run usbboot; run net;' setenv bootfile efi/boot/bootaa64.efi setenv dmi_board_mfg Silicom setenv dmi_board_name 80500-0205-G00 setenv dmi_board_serial 1925200071 setenv dmi_board_ver R301 setenv dmi_chassis_mfg Silicom setenv dmi_chassis_serial 1925200071 setenv dmi_chassis_ver R301 setenv dmi_sys_mfg Silicom setenv dmi_sys_name SG-2100 setenv dmi_sys_serial 1925200071 setenv dmi_sys_ver R301 setenv dtb_name armada-3720-sg2100.dtb setenv efi_8be4df61-93ca-11d2-aa0d-00e098032b8c_OsIndicationsSupported {ro,boot}(blob)0000000000000000 setenv efi_cfee69ad-a0de-47a9-93a8-f63106f8ae99_Boot1Path {boot,run}(blob)2f005c006500660069005c0062006f006f0074005c0062006f006f00740061006100360034002e006500660069000000 setenv eth1addr 00:E0:ED:BC:2E:7A setenv ethaddr 00:E0:ED:BC:2E:79 setenv fileaddr 1000000 setenv filesize 60000 setenv mmcboot 'mmc rescan; setenv load_dev mmc; if fatls ${load_dev} 0:2 /; then run pfsenseboot; fi;' setenv net 'dhcp; tftp ${fdt_addr_r} ${dtb_name}; tftp ${kernel_addr_r} loader.efi; fdt addr ${fdt_addr_r}; fdt set / sn ${dmi_sys_serial}; bootefi ${kernel_addr_r} ${fdt_addr_r};' setenv netgateid 72da527ea24be8b9a7e6 setenv pfsenseboot 'load ${load_dev} 0:2 ${fdt_addr_r} ${dtb_name}; load ${load_dev} 0:1 ${kernel_addr_r} ${boot_file}; fdt addr ${fdt_addr_r}; fdt set / sn ${dmi_sys_serial}; bootefi ${kernel_addr_r} ${fdt_addr_r};' setenv scsiboot 'scsi reset; setenv load_dev scsi; if fatls ${load_dev} 0:2 /; then run pfsenseboot; fi;' setenv setLED 'i2c dev 1; i2c reset; i2c mw 67 ff 0; i2c mw 67 0 1; i2c mw 67 f 20; i2c mw 67 3 40; i2c mw 67 26 0; i2c mw 67 10 0;' setenv usbboot 'usb reset; setenv load_dev usb; if fatls ${load_dev} 0:2 /; then run pfsenseboot; fi;' saveenvYou should run
printenvthere first to make sure those values are all missing or different. They will be if you saw the Bad CRC error in uboot which causes it to load the defaults.
You will need substitute your own serial number, Netgate device ID and MAC address.
The MAC shown on the label is the ethaddr value.Steve
-
Thanks Steve!
If it works then apparently the 1st time I sent the unit for repair was for nothing.
I keep you posted if I make it work.Doron
-
Hi Steve,
I've managed to fix the uboot CRC and now the system can boot correctly.
Thank you!
As you said the ralink 3090 is identified but does not work properly.
Do you have a list of verified wifi cards that work ok with 2.5.0 beta?Doron.
-
Ah, good news and bad then.
What sort of errors are you seeing? How is it not working?
The only card I know to work in the SG-2100 currently (I have tested personally) is the Compex WLE200NX.
Steve
-
Hi Steve,
well I grab a WLE200NX I see in ebay at 16$
the error I get with the relink is :- the wireless SSID is seen but cant be connected.
- an error in the terminal when I enable the interface:
WAN (wan) -> mvneta0 ->
LAN (lan) -> mvneta1 -> v4: 192.168.0.1/24
WLAN (opt1) -> ral0_wlan0 -> v4: 192.168.2.1/24- Logout (SSH only) 9) pfTop
- Assign Interfaces 10) Filter Logs
- Set interface(s) IP address 11) Restart webConfigurator
- Reset webConfigurator password 12) PHP shell + pfSense tools
- Reset to factory defaults 13) Update from console
- Reboot system 14) Enable Secure Shell (sshd)
- Halt system 15) Restore recent configuration
- Ping host 16) Restart PHP-FPM
- Shell
Enter an option: ral0: can't map mbuf (error 27)
ral0: need multicast update callback
ral0: can't map mbuf (error 27)
ral0: can't map mbuf (error 27)
ral0: can't map mbuf (error 27)
ral0: can't map mbuf (error 27)
ral0: can't map mbuf (error 27)
ral0: can't map mbuf (error 27)
