Slow upload speed [SOLVED]
-
Enable powerd and set it for maximum or hiadaptive.
See if that helps. Maybe your CPU isn't ramping up the MHz as the load increases. I know it is an issue on the netgate rangely platforms.YMMV
-
Hi,
Some more testing.
Have turned on PowerD and set it to maximum.
Here's a dump from System Activity in the middle of a running speedtest
last pid: 15237; load averages: 0.30, 0.18, 0.10 up 3+19:26:50 17:29:22
106 processes: 3 running, 83 sleeping, 19 waiting, 1 lockMem: 10M Active, 49M Inact, 48M Wired, 50M Buf, 857M Free
Swap: 2048M Total, 2048M FreePID USERNAME PRI NICE SIZE RES STATE TIME WCPU COMMAND
11 root 155 ki31 0K 8K RUN 87.3H 58.59% [idle]
12 root -92 - 0K 152K WAIT 15:34 26.66% [intr{irq256: re0}]
12 root -92 - 0K 152K WAIT 10:35 14.06% [intr{irq257: re1}]Not really that high load, 0,30 - 0,40.
Is the amount of interrupts on the NICs normal when speedtesting? -
normal? not really … but realtek nics are famous for being horrible. (specially with freebsd)
you could attempt to enable 'device polling' (system-->advanced-->networking). it's intended to stop/greatly reduce interrupts.
DISCLAIMER:
i have no idea if your nic is supported, so it could possibly go wrong and unable to access anything anymore.
enablling device polling is generally not recommanded in any normal situation, but who knows.... -
50% interrupt usage at 25Mb/s is really bad. My Intel NIC hangs around 5% at 1Gb.
-
It didn't support polling so it kinda got stuck when I enabled it.
@harvy66: What boggles me is that I get 100Mbit downstream without any issues, but only 25 up. As if the amount of interrupts would differ(?)
-
Ahh yeah, missed that part. The only guess I can come up with is either the drivers are written that way or there is an interaction between the drivers and how FreeBSD handles moving data. I see no difference in interrupts for uploading or download, except if you include traffic shaping.
-
After alot of desperate attempts, some of them being less scientific than others, I tried putting a 100Mbit switch between the WAN interface and the ISP termination. Turns out I'm now able to do 100/100.
I remove the switch and force the WAN interface to 100Mbit full-duplex (instead of the auto-neg 1Gbit), now 100/100 up/down works like a charm.
Interrupts on the NICs are down to just below 20%.I guess this is another case of Realtek hardware/drivers. However the Linux kernel driver seems to be addressing this better.
Thanks for all the help and replys on the way!
-
drivers. set it up to vmx and all works fine :)
-
Are you using WiFi? That will always provide poorer performance. For example, my connection is 500/20 Mb. When connected via Ethernet, I generally get 550 - 560 Mb down. On 802.11n WiFi, I get about 30 - 40 down. The Ethernet port for my WiFi AP is 100 Mb.
-
@JKnott it was drivers, i am using proxmox and the native network driver gave no upload speed lol. i am in full throttle on my 5ghz :) wifi and hard wired also :)
-
-
@joda We are now in 2023 and this solution has solved my my problem, I replaced the switch with an old 100 mbps switch and it has worked.
What I am thinking about right now is to confer SET (Switch Embedded Team) with one Team Member Port in Hyper-V, after that I think I could use my 1GB switch.Thanks alot!
