Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    LACP not working

    General pfSense Questions
    2
    113
    24.0k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • C
      cyberbot @stephenw10
      last edited by

      @stephenw10 said in LACP not working:

      Ok, then enable lacp debugging and see what gets logged.

      do you to enable this on. the Pfsense? or on the switch?

      1 Reply Last reply Reply Quote 0
      • stephenw10S
        stephenw10 Netgate Administrator
        last edited by

        In pfSense run this command to set it temporarily:

        sysctl net.link.lagg.lacp.debug=1

        Or add it in Sys > Adv > System Tunables to set it more permanently.

        Steve

        C 1 Reply Last reply Reply Quote 0
        • C
          cyberbot @stephenw10
          last edited by

          @stephenw10 said in LACP not working:

          In pfSense run this command to set it temporarily:

          sysctl net.link.lagg.lacp.debug=1

          Or add it in Sys > Adv > System Tunables to set it more permanently.

          Steve

          Steve I appreciate it really. ill do it tomorrow when I get to the office. after I am done with the debug can I disable it using the below command?

          sysctl net.link.lagg.lacp.debug=0
          C 1 Reply Last reply Reply Quote 0
          • stephenw10S
            stephenw10 Netgate Administrator
            last edited by

            Yes exactly.

            Or just reboot since that sysctl is not set in the config.

            Steve

            C 1 Reply Last reply Reply Quote 0
            • C
              cyberbot @stephenw10
              last edited by

              @stephenw10 said in LACP not working:

              Yes exactly.

              Or just reboot since that sysctl is not set in the config.

              Steve

              Steve I appreciate it, ill give it a try tomorrow and report back.
              I hope to see the cause on the debug.

              1 Reply Last reply Reply Quote 0
              • C
                cyberbot @cyberbot
                last edited by

                @cyberbot said in LACP not working:

                @stephenw10 said in LACP not working:

                In pfSense run this command to set it temporarily:

                sysctl net.link.lagg.lacp.debug=1

                Or add it in Sys > Adv > System Tunables to set it more permanently.

                Steve

                Steve I appreciate it really. ill do it tomorrow when I get to the office. after I am done with the debug can I disable it using the below command?

                sysctl net.link.lagg.lacp.debug=0

                Good evening Steve,
                I have enabled the debug, when I connect the cables nothings really shows on the log of console when I was ssh to the box.
                am I supposed to do anything to see those logs?

                1 Reply Last reply Reply Quote 0
                • stephenw10S
                  stephenw10 Netgate Administrator
                  last edited by stephenw10

                  You should see a bunch of entries in the main system log once you enable that.
                  For example:

                  Nov 23 20:06:01 	kernel 		ixl1: lacpdu transmit
Nov 23 20:06:01 	kernel 		actor=(8000,00-E0-ED-86-A6-8C,02B2,8000,0002)
Nov 23 20:06:01 	kernel 		actor.state=3d<ACTIVITY,AGGREGATION,SYNC,COLLECTING,DISTRIBUTING>
Nov 23 20:06:01 	kernel 		partner=(8000,0C-80-63-69-C2-DE,0ADC,8000,001A)
Nov 23 20:06:01 	kernel 		partner.state=3d<ACTIVITY,AGGREGATION,SYNC,COLLECTING,DISTRIBUTING>
Nov 23 20:06:01 	kernel 		maxdelay=0
Nov 23 20:06:01 	kernel 		ixl0: lacpdu transmit
Nov 23 20:06:01 	kernel 		actor=(8000,00-E0-ED-86-A6-8C,02B2,8000,0001)
Nov 23 20:06:01 	kernel 		actor.state=3d<ACTIVITY,AGGREGATION,SYNC,COLLECTING,DISTRIBUTING>
Nov 23 20:06:01 	kernel 		partner=(8000,0C-80-63-69-C2-DE,0ADC,8000,0019)
Nov 23 20:06:01 	kernel 		partner.state=3d<ACTIVITY,AGGREGATION,SYNC,COLLECTING,DISTRIBUTING>
Nov 23 20:06:01 	kernel 		maxdelay=0

                  The problem with that setting is that it fills the system log with data usually. Especially if there's a problem.

                  For reference that is an XG-7100 connected with the X710 expansion card to a Brocade ICX6450. And working correctly.

                  Steve

                  1 Reply Last reply Reply Quote 0
                  • C
                    cyberbot
                    last edited by

                    Sorry Steve,
                    I've found it had to use google ssh to show the logs I don't know why putty didn't wanna shows the logs.

                    lagg0: link state changed to DOWN
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
lagg0: link state changed to UP
em3: Interface stopped DISTRIBUTING, possible flapping
em2: Interface stopped DISTRIBUTING, possible flapping
lagg0: link state changed to DOWN
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
lagg0: link state changed to UP
em3: Interface stopped DISTRIBUTING, possible flapping
em2: Interface stopped DISTRIBUTING, possible flapping
lagg0: link state changed to DOWN
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
lagg0: link state changed to UP
em3: Interface stopped DISTRIBUTING, possible flapping
em2: Interface stopped DISTRIBUTING, possible flapping
                    1 Reply Last reply Reply Quote 0
                    • stephenw10S
                      stephenw10 Netgate Administrator
                      last edited by stephenw10

                      That the console output rather than the system log? It looks like it.

                      You should see more that that at least when it initially comes up. Check the system log in the webgui or use:
                      clog /var/log/system.log at the CLI.

                      Steve

                      C 1 Reply Last reply Reply Quote 0
                      • C
                        cyberbot @stephenw10
                        last edited by cyberbot

                        @stephenw10 said in LACP not working:

                        That the console output rather than the system log? It looks like it.

                        You should see more that that at least when it initially comes up. Check the system log in the webgui or use:
                        clog /var/log/system.log at the CLI.

                        Steve

                        Thank you Steve,
                        I owe you plenty of 🍻
                        I have run the command its shows alot of information I've collected the ones talking about LACP

                        Nov 23 21:13:19 firewall /flowd_aggregate.py[92972]: start watching flowd
Nov 23 21:13:23 firewall /flowd_aggregate.py[92972]: flowparser failed to unpack flow_times (unpack requires a buffer of 8 bytes)
Nov 23 21:13:23 firewall /flowd_aggregate.py[92972]: flowparser failed to unpack as_info (unpack requires a buffer of 12 bytes)
Nov 23 21:13:23 firewall /flowd_aggregate.py[92972]: flowparser failed to unpack flow_engine_info (unpack requires a buffer of 12 bytes)
Nov 23 21:13:23 firewall /flowd_aggregate.py[92972]: flowparser failed to unpack srcdst_port (unpack requires a buffer of 4 bytes)
Nov 23 21:13:23 firewall /flowd_aggregate.py[92972]: flowparser failed to unpack flow_times (unpack requires a buffer of 8 bytes)
Nov 23 21:13:23 firewall /flowd_aggregate.py[92972]: flowparser failed to unpack flow_engine_info (unpack requires a buffer of 12 bytes)
Nov 23 21:13:23 firewall /flowd_aggregate.py[92972]: flowparser failed to unpack tag (unpack requires a buffer of 4 bytes)
Nov 23 21:13:23 firewall /flowd_aggregate.py[92972]: flowparser failed to unpack recv_time (unpack requires a buffer of 8 bytes)
Nov 23 21:13:23 firewall /flowd_aggregate.py[92972]: flowparser failed to unpack srcdst_port (unpack requires a buffer of 4 bytes)
Nov 23 21:13:23 firewall /flowd_aggregate.py[92972]: flowparser failed to unpack flow_times (unpack requires a buffer of 8 bytes)
Nov 23 21:13:23 firewall /flowd_aggregate.py[92972]: flowparser failed to unpack flow_engine_info (unpack requires a buffer of 12 bytes)
Nov 23 21:12:06 firewall kernel: pflog0: promiscuous mode disabled
Nov 23 21:12:06 firewall kernel: pflog0: promiscuous mode enabled
Nov 23 21:12:06 firewall /flowd_aggregate.py[92972]: startup, check database.

                        on the switch side I have this

                        === LAG "Pfsense" ID 1 (dynamic Deployed) ===
LAG Configuration:
   Ports:         e 1/2/2 e 1/2/4
   Port Count:    2
   Primary Port:  1/2/2
   Trunk Type:    hash-based
   LACP Key:      20001
Deployment: HW Trunk ID 1
Port       Link    State   Dupl Speed Trunk Tag Pvid Pri MAC             Name
1/2/2      Up      Blocked Full 1G    1     Yes 18   0   609c.9f3a.a488  1/2/4      Up      Blocked  Full 1G   1     Yes 18   0   609c.9f3a.a488

Port       [Sys P] [Port P] [ Key ] [Act][Tio][Agg][Syn][Col][Dis][Def][Exp][Ope]
1/2/2           1        1   20001   Yes   S   Agg  Syn  Col  Dis  Def  No   Ina
1/2/4           1        1   20001   Yes   S   Agg  Syn  No   No   Def  No   Ina
                        C 1 Reply Last reply Reply Quote 0
                        • stephenw10S
                          stephenw10 Netgate Administrator
                          last edited by

                          OK, the flowd stuff is not relevant. You need to looks at the lacpdu output which should look at least vaguely like my output above.
                          It's all from the 'kernel' process so you can filter by that to lose all the netflow entries.

                          The fact the switch shows the ports as blocked is not good...

                          Steve

                          C 1 Reply Last reply Reply Quote 0
                          • C
                            cyberbot @stephenw10
                            last edited by

                            @stephenw10 said in LACP not working:

                            OK, the flowd stuff is not relevant. You need to looks at the lacpdu output which should look at least vaguely like my output above.
                            It's all from the 'kernel' process so you can filter by that to lose all the netflow entries.

                            The fact the switch shows the ports as blocked is not good...

                            Steve

                            Thank you Steve,

                            if the switch shows they are blocked mostly is the switch or the pfsense?

                            1 Reply Last reply Reply Quote 0
                            • C
                              cyberbot @cyberbot
                              last edited by

                              @cyberbot said in LACP not working:

                              @stephenw10 said in LACP not working:

                              That the console output rather than the system log? It looks like it.

                              You should see more that that at least when it initially comes up. Check the system log in the webgui or use:
                              clog /var/log/system.log at the CLI.

                              Steve

                              Thank you Steve,
                              I owe you plenty of 🍻
                              I have run the command its shows alot of information I've collected the ones talking about LACP

                              Nov 23 21:13:19 firewall /flowd_aggregate.py[92972]: start watching flowd
Nov 23 21:13:23 firewall /flowd_aggregate.py[92972]: flowparser failed to unpack flow_times (unpack requires a buffer of 8 bytes)
Nov 23 21:13:23 firewall /flowd_aggregate.py[92972]: flowparser failed to unpack as_info (unpack requires a buffer of 12 bytes)
Nov 23 21:13:23 firewall /flowd_aggregate.py[92972]: flowparser failed to unpack flow_engine_info (unpack requires a buffer of 12 bytes)
Nov 23 21:13:23 firewall /flowd_aggregate.py[92972]: flowparser failed to unpack srcdst_port (unpack requires a buffer of 4 bytes)
Nov 23 21:13:23 firewall /flowd_aggregate.py[92972]: flowparser failed to unpack flow_times (unpack requires a buffer of 8 bytes)
Nov 23 21:13:23 firewall /flowd_aggregate.py[92972]: flowparser failed to unpack flow_engine_info (unpack requires a buffer of 12 bytes)
Nov 23 21:13:23 firewall /flowd_aggregate.py[92972]: flowparser failed to unpack tag (unpack requires a buffer of 4 bytes)
Nov 23 21:13:23 firewall /flowd_aggregate.py[92972]: flowparser failed to unpack recv_time (unpack requires a buffer of 8 bytes)
Nov 23 21:13:23 firewall /flowd_aggregate.py[92972]: flowparser failed to unpack srcdst_port (unpack requires a buffer of 4 bytes)
Nov 23 21:13:23 firewall /flowd_aggregate.py[92972]: flowparser failed to unpack flow_times (unpack requires a buffer of 8 bytes)
Nov 23 21:13:23 firewall /flowd_aggregate.py[92972]: flowparser failed to unpack flow_engine_info (unpack requires a buffer of 12 bytes)
Nov 23 21:12:06 firewall kernel: pflog0: promiscuous mode disabled
Nov 23 21:12:06 firewall kernel: pflog0: promiscuous mode enabled
Nov 23 21:12:06 firewall /flowd_aggregate.py[92972]: startup, check database.

                              on the switch side I have this

                              === LAG "Pfsense" ID 1 (dynamic Deployed) ===
LAG Configuration:
   Ports:         e 1/2/2 e 1/2/4
   Port Count:    2
   Primary Port:  1/2/2
   Trunk Type:    hash-based
   LACP Key:      20001
Deployment: HW Trunk ID 1
Port       Link    State   Dupl Speed Trunk Tag Pvid Pri MAC             Name
1/2/2      Up      Blocked Full 1G    1     Yes 18   0   609c.9f3a.a488  1/2/4      Up      Blocked  Full 1G   1     Yes 18   0   609c.9f3a.a488

Port       [Sys P] [Port P] [ Key ] [Act][Tio][Agg][Syn][Col][Dis][Def][Exp][Ope]
1/2/2           1        1   20001   Yes   S   Agg  Syn  Col  Dis  Def  No   Ina
1/2/4           1        1   20001   Yes   S   Agg  Syn  No   No   Def  No   Ina

                              Hi Steve.
                              I have this log now after I connect the cables.

                              Nov 24 00:13:35 firewall kernel: em2: lacpdu receive
Nov 24 00:13:35 firewall kernel: actor=(0001,60-9C-9F-4B-80-8C,4E22,0001,0002)
Nov 24 00:13:35 firewall kernel: actor.state=7<ACTIVITY,TIMEOUT,AGGREGATION>
Nov 24 00:13:35 firewall kernel: partner=(8000,E8-39-35-11-FA-AB,016B,8000,0003)
Nov 24 00:13:35 firewall kernel: partner.state=1d<ACTIVITY,AGGREGATION,SYNC,COLLECTING>
Nov 24 00:13:35 firewall kernel: maxdelay=0
Nov 24 00:13:35 firewall kernel: em2: old pstate cf<ACTIVITY,TIMEOUT,AGGREGATION,SYNC,DEFAULTED,EXPIRED>
Nov 24 00:13:35 firewall kernel: em2: new pstate f<ACTIVITY,TIMEOUT,AGGREGATION,SYNC>
Nov 24 00:13:35 firewall kernel: em3: lacpdu transmit
Nov 24 00:13:35 firewall kernel: actor=(8000,E8-39-35-11-FA-AB,016B,8000,0004)
Nov 24 00:13:35 firewall kernel: actor.state=1d<ACTIVITY,AGGREGATION,SYNC,COLLECTING>
Nov 24 00:13:35 firewall kernel: partner=(0001,60-9C-9F-4B-80-8C,4E22,0001,0102)
Nov 24 00:13:35 firewall kernel: partner.state=cf<ACTIVITY,TIMEOUT,AGGREGATION,SYNC,DEFAULTED,EXPIRED>
Nov 24 00:13:35 firewall kernel: maxdelay=0
Nov 24 00:13:35 firewall kernel: em2: lacpdu transmit
Nov 24 00:13:35 firewall kernel: actor=(8000,E8-39-35-11-FA-AB,016B,8000,0003)
Nov 24 00:13:35 firewall kernel: actor.state=1d<ACTIVITY,AGGREGATION,SYNC,COLLECTING>
Nov 24 00:13:35 firewall kernel: partner=(0001,60-9C-9F-4B-80-8C,4E22,0001,0002)
Nov 24 00:13:35 firewall kernel: partner.state=f<ACTIVITY,TIMEOUT,AGGREGATION,SYNC>
Nov 24 00:13:35 firewall kernel: maxdelay=0

                              and the switch still showing the ports are blocked.

                              LAG Configuration:
   Ports:         e 1/1/2 e 2/1/2
   Port Count:    2
   Primary Port:  1/1/2
   Trunk Type:    hash-based
   LACP Key:      20002
Deployment: HW Trunk ID 2
Port       Link    State   Dupl Speed Trunk Tag Pvid Pri MAC             Name
1/1/2      Up      Blocked Full 1G    2     Yes N/A  0   609c.9f4b.808d  LAN1
2/1/2      Up      Blocked Full 1G    2     Yes N/A  0   609c.9f4b.808d  LAN2

Port       [Sys P] [Port P] [ Key ] [Act][Tio][Agg][Syn][Col][Dis][Def][Exp][Ope]
1/1/2           1        1   20002   Yes   S   Agg  No   No   No   No   No   Ina
2/1/2           1        1   20002   Yes   S   Agg  Syn  No   No   Def  Exp  Err
                              1 Reply Last reply Reply Quote 0
                              • stephenw10S
                                stephenw10 Netgate Administrator
                                last edited by

                                The switch probably blocked the ports for the same reason pfSense stopped the interfaces.
                                They were flapping for some reason and leaving them running like that could cause far more problems. We have to try to find out why.

                                I would disconnect and reconnect the ports and see what is logged.

                                Try connecting only one port and see if that prevents the flapping.

                                Steve

                                C 1 Reply Last reply Reply Quote 0
                                • C
                                  cyberbot @stephenw10
                                  last edited by cyberbot

                                  After I connected the cables one by one it still shows the flapping, but the error comes up.

                                  Nov 24 01:07:31 firewall configctl[3820]: event @ 1606176450.60 exec: system event config_changed
Nov 24 01:07:38 firewall kernel: em2: Interface stopped DISTRIBUTING, possible flapping
Nov 24 01:07:38 firewall kernel: lagg0: link state changed to DOWN
Nov 24 01:07:43 firewall kernel: lagg0: link state changed to UP
Nov 24 01:07:44 firewall kernel: em2: Interface stopped DISTRIBUTING, possible flapping
Nov 24 01:07:44 firewall kernel: lagg0: link state changed to DOWN
Nov 24 01:07:49 firewall kernel: lagg0: link state changed to UP
Nov 24 01:07:51 firewall kernel: em2: Interface stopped DISTRIBUTING, possible flapping
Nov 24 01:07:51 firewall kernel: lagg0: link state changed to DOWN
Nov 24 01:07:56 firewall kernel: lagg0: link state changed to UP
Nov 24 01:07:57 firewall kernel: em2: Interface stopped DISTRIBUTING, possible flapping
Nov 24 01:07:57 firewall kernel: lagg0: link state changed to DOWN
Nov 24 01:08:02 firewall kernel: lagg0: link state changed to UP
Nov 24 01:08:03 firewall kernel: em2: Interface stopped DISTRIBUTING, possible flapping
Nov 24 01:08:03 firewall kernel: lagg0: link state changed to DOWN
Nov 24 01:08:08 firewall kernel: lagg0: link state changed to UP
Nov 24 01:08:09 firewall kernel: em2: Interface stopped DISTRIBUTING, possible flapping
Nov 24 01:08:09 firewall kernel: lagg0: link state changed to DOWN
Nov 24 01:08:14 firewall kernel: lagg0: link state changed to UP
Nov 24 01:08:15 firewall kernel: em2: Interface stopped DISTRIBUTING, possible flapping
Nov 24 01:08:15 firewall kernel: lagg0: link state changed to DOWN
Nov 24 01:08:20 firewall kernel: lagg0: link state changed to UP

                                  ifconfig laag0 show

                                  lagg0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=850098<VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,VLAN_HWFILTER,VLAN_HWTSO>
        ether e8:39:35:11:fa:ab
        inet6 fe80::ea39:35ff:fe11:faab%lagg0 prefixlen 64 scopeid 0xb
        inet 192.168.55.1 netmask 0xffffff00 broadcast 192.168.55.255
        laggproto lacp lagghash l2,l3,l4
        laggport: em2 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING>
        laggport: em3 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING>
        groups: lagg
        media: Ethernet autoselect
        status: active
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
                                  1 Reply Last reply Reply Quote 0
                                  • stephenw10S
                                    stephenw10 Netgate Administrator
                                    last edited by stephenw10

                                    Maybe check debugging is still enabled. You should see some log entries from lacp there.

                                    Edit: Sorry missed a whole post of yours somehow. Ok I see logs showinh both ends timing out.

                                    And it still showed flapping with only one NIC connected? em2 there in the logs?

                                    What do you see if you run: ifconfig -vv lagg0?

                                    Steve

                                    C 1 Reply Last reply Reply Quote 0
                                    • stephenw10S
                                      stephenw10 Netgate Administrator
                                      last edited by

                                      Looking at the switch there it looks like you might have short timeouts set?

                                      For reference:

                                      SSH@ICX6450-24P Switch>show lag
Total number of LAGs:          1
Total number of deployed LAGs: 1
Total number of trunks created:1 (123 available)
LACP System Priority / ID:     1 / 609c.9f54.14f2
LACP Long timeout:             90, default: 90
LACP Short timeout:            3, default: 3

=== LAG "lacp1" ID 2047 (dynamic Deployed) ===
LAG Configuration:
   Ports:         e 1/2/1 e 1/2/3 
   Port Count:    2
   Primary Port:  1/2/1
   Trunk Type:    hash-based
   LACP Key:      22047
   LACP Timeout:  long
Deployment: HW Trunk ID 1
Port       Link    State   Dupl Speed Trunk Tag Pvid Pri MAC             Name
1/2/1      Up      Learn   Full 10G   2047  No  1    0   609c.9f54.150b                 
1/2/3      Up      Learn   Full 10G   2047  No  1    0   609c.9f54.150b                 

Port       [Sys P] [Port P] [ Key ] [Act][Tio][Agg][Syn][Col][Dis][Def][Exp][Ope]
1/2/1           1        1   22047   Yes   L   Agg  Syn  Col  Dis  No   No   Ope
1/2/3           1        1   22047   Yes   L   Agg  Syn  Col  Dis  No   No   Ope
                                                                  

 Partner Info and PDU Statistics 
Port          Partner         Partner     LACP      LACP     
             System ID         Key     Rx Count  Tx Count  
1/2/1    32768-00e0.ed86.a68c      690        4         4
1/2/3    32768-00e0.ed86.a68c      690        3         5
                                      1 Reply Last reply Reply Quote 0
                                      • C
                                        cyberbot @stephenw10
                                        last edited by cyberbot

                                        @stephenw10 said in LACP not working:

                                        Maybe check debugging is still enabled. You should see some log entries from lacp there.

                                        Edit: Sorry missed a whole post of yours somehow. Ok I see logs showinh both ends timing out.

                                        And it still showed flapping with only one NIC connected? em2 there in the logs?

                                        What do you see if you run: ifconfig -vv lagg0?

                                        Steve

                                        Hi Steve
                                        yes each NIC I connect em0 or em3 it shows the flagging error.
                                        what do you mean with time out of set?

                                        root@pfsense:~ # ifconfig -vv lagg0
lagg0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=8520b8<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO>
        ether 00:08:a2:0c:99:7b
        inet6 fe80::208:a2ff:fe0c:997b%lagg0 prefixlen 64 scopeid 0x10
        inet 192.168.15.1 netmask 0xffffff00 broadcast 192.168.15.255
        laggproto lacp lagghash l2,l3,l4
        lagg options:
                flags=10<LACP_STRICT>
                flowid_shift: 16
        lagg statistics:
                active ports: 2
                flapping: 0
        lag id: [(8000,00-08-A2-0C-99-7B,020B,0000,0000),
                 (8000,74-83-C2-48-2F-67,0042,0000,0000)]
        laggport: igb4 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING> state=3d<ACTIVITY,AGGREGATION,SYNC,COLLECTING,DISTRIBUTING>
                [(8000,00-08-A2-0C-99-7B,020B,8000,0005),
                 (8000,74-83-C2-48-2F-67,0042,0080,0017)]
        laggport: igb5 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING> state=3d<ACTIVITY,AGGREGATION,SYNC,COLLECTING,DISTRIBUTING>
                [(8000,00-08-A2-0C-99-7B,020B,8000,0006),
                 (8000,74-83-C2-48-2F-67,0042,0080,0018)]
        groups: lagg
        media: Ethernet autoselect
        status: active
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
                                        1 Reply Last reply Reply Quote 0
                                        • stephenw10S
                                          stephenw10 Netgate Administrator
                                          last edited by

                                          My switch is set for Long LACP timeouts (the TIO flag) and yours it set short.

                                          Try changing that.

                                          C 1 Reply Last reply Reply Quote 0
                                          • C
                                            cyberbot @stephenw10
                                            last edited by cyberbot

                                            @stephenw10 said in LACP not working:

                                            My switch is set for Long LACP timeouts (the TIO flag) and yours it set short.

                                            Try changing that.

                                            Are you using a broadcom switch?
                                            i have changed the timeouts to long

                                            device(config)# lag blue dynamic
device(config-lag-blue)# lacp-timeout long

                                            but it stills shows blocked

                                            === LAG "Pfsense WAN" ID 1 (dynamic Deployed) ===
LAG Configuration:
   Ports:         e 1/1/1 e 2/1/1
   Port Count:    2
   Primary Port:  1/1/1
   Trunk Type:    hash-based
   LACP Key:      20001
Deployment: HW Trunk ID 1
Port       Link    State   Dupl Speed Trunk Tag Pvid Pri MAC             Name
1/1/1      Up      Blocked Full 1G    1     No  141  0   609c.9f4b.808c  WAN1
2/1/1      Up      Blocked Full 1G    1     No  141  0   609c.9f4b.808c  WAN2

Port       [Sys P] [Port P] [ Key ] [Act][Tio][Agg][Syn][Col][Dis][Def][Exp][Ope]
1/1/1           1        1   20001   Yes   S   Agg  No   No   No   Def  Exp  Err
2/1/1           1        1   20001   Yes   S   Agg  No   No   No   Def  Exp  Err


 Partner Info and PDU Statistics
Port          Partner         Partner     LACP      LACP
             System ID         Key     Rx Count  Tx Count
1/1/1    4-e839.3511.faab        0        0         1
2/1/1    3-e839.3511.faab        0        0         1
                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.