LAN hotplug errors after upgrade to 2.5.0

[stephenw10]

Are you able to check whatever it's connected to to see if it is actually dropping the link for some reason?

Steve

[TechGeek01]

@stephenw10 The switch it's connected to does indeed show disconnect and reconnect log messages (Dell 5548). That's what initially led me to believe it's a hardware thing, but I've tried swapping with a known good cable, and same result.

Still only happens really under load though. If I leave it idle while I'm at work, I don't really see the disconnect messages or anything.

[stephenw10]

You might check the stats from sysctl dev.em.1 and the settings in sysctl hw.em.

Steve

[TechGeek01]

@stephenw10

sysctl dev.em.1

dev.em.1.wake: 0
dev.em.1.interrupts.rx_overrun: 0
dev.em.1.interrupts.rx_desc_min_thresh: 0
dev.em.1.interrupts.tx_queue_min_thresh: 0
dev.em.1.interrupts.tx_queue_empty: 0
dev.em.1.interrupts.tx_abs_timer: 0
dev.em.1.interrupts.tx_pkt_timer: 0
dev.em.1.interrupts.rx_abs_timer: 0
dev.em.1.interrupts.rx_pkt_timer: 0
dev.em.1.interrupts.asserts: 216
dev.em.1.mac_stats.tso_ctx_fail: 0
dev.em.1.mac_stats.tso_txd: 0
dev.em.1.mac_stats.tx_frames_1024_1522: 1495503167
dev.em.1.mac_stats.tx_frames_512_1023: 16495480
dev.em.1.mac_stats.tx_frames_256_511: 14855170
dev.em.1.mac_stats.tx_frames_128_255: 25114525
dev.em.1.mac_stats.tx_frames_65_127: 206999058
dev.em.1.mac_stats.tx_frames_64: 85971859
dev.em.1.mac_stats.mcast_pkts_txd: 441585
dev.em.1.mac_stats.bcast_pkts_txd: 13798
dev.em.1.mac_stats.good_pkts_txd: 1844939137
dev.em.1.mac_stats.total_pkts_txd: 1844939231
dev.em.1.mac_stats.good_octets_txd: 2312840063914
dev.em.1.mac_stats.good_octets_recvd: 2129400200140
dev.em.1.mac_stats.rx_frames_1024_1522: 1367756134
dev.em.1.mac_stats.rx_frames_512_1023: 16606429
dev.em.1.mac_stats.rx_frames_256_511: 5846534
dev.em.1.mac_stats.rx_frames_128_255: 32959675
dev.em.1.mac_stats.rx_frames_65_127: 346945240
dev.em.1.mac_stats.rx_frames_64: 1566882
dev.em.1.mac_stats.mcast_pkts_recvd: 1942808
dev.em.1.mac_stats.bcast_pkts_recvd: 478650
dev.em.1.mac_stats.good_pkts_recvd: 1771680901
dev.em.1.mac_stats.total_pkts_recvd: 1771681360
dev.em.1.mac_stats.xoff_txd: 1
dev.em.1.mac_stats.xoff_recvd: 0
dev.em.1.mac_stats.xon_txd: 1
dev.em.1.mac_stats.xon_recvd: 0
dev.em.1.mac_stats.coll_ext_errs: 0
dev.em.1.mac_stats.alignment_errs: 0
dev.em.1.mac_stats.crc_errs: 35
dev.em.1.mac_stats.recv_errs: 22
dev.em.1.mac_stats.recv_jabber: 22
dev.em.1.mac_stats.recv_oversize: 295
dev.em.1.mac_stats.recv_fragmented: 0
dev.em.1.mac_stats.recv_undersize: 0
dev.em.1.mac_stats.recv_no_buff: 91985175
dev.em.1.mac_stats.missed_packets: 0
dev.em.1.mac_stats.defer_count: 0
dev.em.1.mac_stats.sequence_errors: 0
dev.em.1.mac_stats.symbol_errors: 0
dev.em.1.mac_stats.collision_count: 0
dev.em.1.mac_stats.late_coll: 0
dev.em.1.mac_stats.multiple_coll: 0
dev.em.1.mac_stats.single_coll: 0
dev.em.1.mac_stats.excess_coll: 0
dev.em.1.queue_rx_1.rx_irq: 0
dev.em.1.queue_rx_1.rxd_tail: 452
dev.em.1.queue_rx_1.rxd_head: 455
dev.em.1.queue_rx_0.rx_irq: 0
dev.em.1.queue_rx_0.rxd_tail: 155
dev.em.1.queue_rx_0.rxd_head: 158
dev.em.1.queue_tx_1.tx_irq: 0
dev.em.1.queue_tx_1.txd_tail: 609
dev.em.1.queue_tx_1.txd_head: 605
dev.em.1.queue_tx_0.tx_irq: 0
dev.em.1.queue_tx_0.txd_tail: 533
dev.em.1.queue_tx_0.txd_head: 532
dev.em.1.fc_low_water: 16932
dev.em.1.fc_high_water: 18432
dev.em.1.rx_control: 67403806
dev.em.1.device_control: 1477444168
dev.em.1.watchdog_timeouts: 0
dev.em.1.rx_overruns: 0
dev.em.1.link_irq: 74
dev.em.1.dropped: 72
dev.em.1.eee_control: 1
dev.em.1.itr: 488
dev.em.1.tx_abs_int_delay: 66
dev.em.1.rx_abs_int_delay: 66
dev.em.1.tx_int_delay: 66
dev.em.1.rx_int_delay: 0
dev.em.1.rs_dump: 0
dev.em.1.reg_dump: General Registers
        CTRL     58100248
        STATUS   00080783
        CTRL_EXIT        80580000

Interrupt Registers
        ICR      80a00083

RX Registers
        RCTL     0404801e
        RDLEN    00004000
        RDH      000000a3
        RDT      000000a2
        RXDCTL   01050420
        RDBAL    04414000
        RDBAH    00000000

TX Registers
        TCTL     3103f0fa
        TDBAL    057cc000
        TDBAH    00000000
        TDLEN    00004000
        TDH      0000022d
        TDT      0000022d
        TXDCTL   0341011f
        TDFH     00000b97
        TDFT     0000137c
        TDFHS    00000bea
        TDFPC    0000000a


dev.em.1.fc: 3
dev.em.1.debug: -1
dev.em.1.nvm: -1
dev.em.1.iflib.rxq1.rxq_fl0.buf_size: 2048
dev.em.1.iflib.rxq1.rxq_fl0.credits: 1023
dev.em.1.iflib.rxq1.rxq_fl0.cidx: 520
dev.em.1.iflib.rxq1.rxq_fl0.pidx: 519
dev.em.1.iflib.rxq0.rxq_fl0.buf_size: 2048
dev.em.1.iflib.rxq0.rxq_fl0.credits: 1023
dev.em.1.iflib.rxq0.rxq_fl0.cidx: 166
dev.em.1.iflib.rxq0.rxq_fl0.pidx: 165
dev.em.1.iflib.txq1.r_abdications: 0
dev.em.1.iflib.txq1.r_restarts: 0
dev.em.1.iflib.txq1.r_stalls: 0
dev.em.1.iflib.txq1.r_starts: 13052377
dev.em.1.iflib.txq1.r_drops: 0
dev.em.1.iflib.txq1.r_enqueues: 13058272
dev.em.1.iflib.txq1.ring_state: pidx_head: 0699 pidx_tail: 0699 cidx: 0699 state: IDLE
dev.em.1.iflib.txq1.txq_cleaned: 13726331
dev.em.1.iflib.txq1.txq_processed: 13726379
dev.em.1.iflib.txq1.txq_in_use: 50
dev.em.1.iflib.txq1.txq_cidx_processed: 685
dev.em.1.iflib.txq1.txq_cidx: 645
dev.em.1.iflib.txq1.txq_pidx: 695
dev.em.1.iflib.txq1.no_tx_dma_setup: 0
dev.em.1.iflib.txq1.txd_encap_efbig: 0
dev.em.1.iflib.txq1.tx_map_failed: 0
dev.em.1.iflib.txq1.no_desc_avail: 0
dev.em.1.iflib.txq1.mbuf_defrag_failed: 0
dev.em.1.iflib.txq1.m_pullups: 1844
dev.em.1.iflib.txq1.mbuf_defrag: 0
dev.em.1.iflib.txq0.r_abdications: 0
dev.em.1.iflib.txq0.r_restarts: 0
dev.em.1.iflib.txq0.r_stalls: 0
dev.em.1.iflib.txq0.r_starts: 679332
dev.em.1.iflib.txq0.r_drops: 0
dev.em.1.iflib.txq0.r_enqueues: 679664
dev.em.1.iflib.txq0.ring_state: pidx_head: 1840 pidx_tail: 1840 cidx: 1840 state: IDLE
dev.em.1.iflib.txq0.txq_cleaned: 1355334
dev.em.1.iflib.txq0.txq_processed: 1355378
dev.em.1.iflib.txq0.txq_in_use: 54
dev.em.1.iflib.txq0.txq_cidx_processed: 626
dev.em.1.iflib.txq0.txq_cidx: 586
dev.em.1.iflib.txq0.txq_pidx: 640
dev.em.1.iflib.txq0.no_tx_dma_setup: 0
dev.em.1.iflib.txq0.txd_encap_efbig: 0
dev.em.1.iflib.txq0.tx_map_failed: 0
dev.em.1.iflib.txq0.no_desc_avail: 0
dev.em.1.iflib.txq0.mbuf_defrag_failed: 0
dev.em.1.iflib.txq0.m_pullups: 1912
dev.em.1.iflib.txq0.mbuf_defrag: 0
dev.em.1.iflib.override_nrxds: 0
dev.em.1.iflib.override_ntxds: 0
dev.em.1.iflib.separate_txrx: 0
dev.em.1.iflib.core_offset: 1
dev.em.1.iflib.tx_abdicate: 0
dev.em.1.iflib.rx_budget: 0
dev.em.1.iflib.disable_msix: 0
dev.em.1.iflib.override_qs_enable: 0
dev.em.1.iflib.override_nrxqs: 0
dev.em.1.iflib.override_ntxqs: 0
dev.em.1.iflib.driver_version: 7.6.1-k
dev.em.1.%parent: pci2
dev.em.1.%pnpinfo: vendor=0x8086 device=0x10d3 subvendor=0x15d9 subdevice=0x0000 class=0x020000
dev.em.1.%location: slot=0 function=0 dbsf=pci0:2:0:0 handle=\_SB_.PCI0.RP05.PXSX
dev.em.1.%driver: em
dev.em.1.%desc: Intel(R) PRO/1000 Network Connection

sysctl hw.em

hw.em.max_interrupt_rate: 8000
hw.em.eee_setting: 1
hw.em.rx_process_limit: 100
hw.em.sbp: 1
hw.em.smart_pwr_down: 0
hw.em.rx_abs_int_delay: 66
hw.em.tx_abs_int_delay: 66
hw.em.rx_int_delay: 0
hw.em.tx_int_delay: 66
hw.em.disable_crc_stripping: 0

[stephenw10]

Hmm, nothing jumps out there. Pretty much what I see on a test box here.

At this point I would probably be swapping em0 and em1 to be sure it's not a hardware issue.

Steve

[TechGeek01]

@stephenw10 I will give that a shot when I get home.

Out of curiosity, if I'm understanding this correctly, it seems like the log messages are indicating a new WAN IP is triggering an interface reload. Am I correct there? Meaning swapping them would go from triggering a reload to the LAN just periodically dropping connectivity?

Also, the motherboard is a Supermicro X9SCM, so both NICs are on board, not that it makes much of a difference.

[TechGeek01]

@stephenw10 Okay, so swapping the two, first thing I noticed is the clip on the WAN cable isn't broken off, but it doesn't click. I was planning on re-crimping that end, but out of curiosity, I let everything come back up after a config change (backup config, swap em0 and em1, and import modified config), and I unplugged, left, and plugged back in the WAN on em1.

I see the log is much shorter for hotplug on WAN compared to LAN, though I suspect that's just cause of all the LAN subinterfaces. I did noticed that instead of a "hotplug" message, this time the singular message is "HOTPLUG," and there's only one mention of it. I don't quite know if that's a different thing or not.

I'm currently hammering everything with a 240GB file transfer to see if I can get the error to pop up again on its own with the NIC swap. In the mean time, any idea why a physical unplug generates different log messages than what I was seeing before? Logs are as follows:

Mar  7 19:22:24 hydrogen check_reload_status[309]: Linkup starting em1
Mar  7 19:22:24 hydrogen kernel: em1: link state changed to DOWN
Mar  7 19:22:25 hydrogen php-fpm[270]: /rc.linkup: DEVD Ethernet detached event for wan
Mar  7 19:22:26 hydrogen check_reload_status[309]: Reloading filter
Mar  7 19:22:43 hydrogen rc.gateway_alarm[90687]: >>> Gateway alarm: WAN_DHCP (Addr:1.1.1.1 Alarm:1 RTT:696.418ms RTTsd:130.285ms Loss:26%)
Mar  7 19:22:43 hydrogen check_reload_status[309]: updating dyndns WAN_DHCP
Mar  7 19:22:43 hydrogen check_reload_status[309]: Restarting ipsec tunnels
Mar  7 19:22:43 hydrogen check_reload_status[309]: Restarting OpenVPN tunnels/interfaces
Mar  7 19:22:43 hydrogen check_reload_status[309]: Reloading filter
Mar  7 19:22:44 hydrogen php-fpm[83648]: /rc.openvpn: Gateway, NONE AVAILABLE
Mar  7 19:22:44 hydrogen php-fpm[83648]: /rc.openvpn: OpenVPN: One or more OpenVPN tunnel endpoints may have changed its IP. Reloading endpoints that may use WAN_DHCP.
Mar  7 19:22:44 hydrogen php-fpm[271]: /rc.dyndns.update: Dynamic DNS (522789) There was an error trying to determine the public IP for interface - wan (em1 ).
Mar  7 19:22:45 hydrogen php-fpm[271]: /rc.dyndns.update: Dynamic DNS (home.REDACTED) There was an error trying to determine the public IP for interface - wan (em1 ).
Mar  7 19:22:46 hydrogen php-fpm[271]: /rc.dyndns.update: Dynamic DNS (mail.REDACTED) There was an error trying to determine the public IP for interface - wan (em1 ).
Mar  7 19:22:47 hydrogen php-fpm[271]: /rc.dyndns.update: Dynamic DNS (bitwarden.REDACTED) There was an error trying to determine the public IP for interface - wan (em1 ).
Mar  7 19:23:27 hydrogen kernel: ovpns2: link state changed to DOWN
Mar  7 19:23:27 hydrogen check_reload_status[309]: Reloading filter
Mar  7 19:23:53 hydrogen check_reload_status[309]: Linkup starting em1
Mar  7 19:23:53 hydrogen kernel: em1: link state changed to UP
Mar  7 19:23:54 hydrogen php-fpm[270]: /rc.linkup: DEVD Ethernet attached event for wan
Mar  7 19:23:54 hydrogen php-fpm[270]: /rc.linkup: HOTPLUG: Configuring interface wan
Mar  7 19:23:56 hydrogen check_reload_status[309]: rc.newwanip starting em1
Mar  7 19:23:56 hydrogen php-fpm[270]: /rc.linkup: calling interface_dhcpv6_configure.
Mar  7 19:23:56 hydrogen php-fpm[270]: /rc.linkup: Accept router advertisements on interface em1 
Mar  7 19:23:56 hydrogen php-fpm[270]: /rc.linkup: Starting rtsold process
Mar  7 19:23:57 hydrogen php-fpm[10424]: /rc.newwanip: rc.newwanip: Info: starting on em1.
Mar  7 19:23:57 hydrogen php-fpm[10424]: /rc.newwanip: rc.newwanip: on (IP address: 99.198.53.111) (interface: WAN[wan]) (real interface: em1).
Mar  7 19:23:57 hydrogen php-fpm[10424]: /rc.newwanip: Accept router advertisements on interface em1 
Mar  7 19:23:57 hydrogen php-fpm[10424]: /rc.newwanip: Starting rtsold process
Mar  7 19:23:58 hydrogen php-fpm[270]: /rc.linkup: Gateway, NONE AVAILABLE
Mar  7 19:23:58 hydrogen check_reload_status[309]: Restarting ipsec tunnels
Mar  7 19:23:58 hydrogen rtsold[90613]: <cap_rssend> sendmsg on em1: Permission denied
Mar  7 19:23:59 hydrogen php-fpm[10424]: /rc.newwanip: The command '/usr/sbin/rtsold -1 -p /var/run/rtsold_em1.pid -M /var/etc/rtsold_em1_script.sh -O /var/etc/rtsold_em1_script.sh em1' returned exit code '1', the output was 'rtsold: failed to open pidfile: File exists' 
Mar  7 19:23:59 hydrogen check_reload_status[309]: Reloading filter
Mar  7 19:24:01 hydrogen check_reload_status[309]: updating dyndns wan
Mar  7 19:24:01 hydrogen php-fpm[270]: /rc.linkup: Removing static route for monitor 1.1.1.1 and adding a new route through [REDACTED]
Mar  7 19:24:01 hydrogen check_reload_status[309]: Reloading filter
Mar  7 19:24:02 hydrogen rtsold[90613]: <cap_rssend> sendmsg on em1: Permission denied
Mar  7 19:24:03 hydrogen php-fpm[83648]: /rc.dyndns.update: phpDynDNS (522789): No change in my IP address and/or 25 days has not passed. Not updating dynamic DNS entry.
Mar  7 19:24:04 hydrogen php-fpm[83648]: /rc.dyndns.update: phpDynDNS (home.REDACTED): No change in my IP address and/or 25 days has not passed. Not updating dynamic DNS entry.
Mar  7 19:24:05 hydrogen php-fpm[83648]: /rc.dyndns.update: phpDynDNS (mail.REDACTED): No change in my IP address and/or 25 days has not passed. Not updating dynamic DNS entry.
Mar  7 19:24:06 hydrogen rtsold[90613]: <cap_rssend> sendmsg on em1: Permission denied
Mar  7 19:24:06 hydrogen php-fpm[83648]: /rc.dyndns.update: phpDynDNS (bitwarden.REDACTED![hr-H-T-123456-unload-standup-base.png](/assets/uploads/files/1615167452915-hr-h-t-123456-unload-standup-base.png) ): No change in my IP address and/or 25 days has not passed. Not updating dynamic DNS entry.

[TechGeek01]

@stephenw10 Just an update, I swapped the NICs, and re-crimped the end on the WAN cable, and have seen no issues at all since then.

Out of curiosity, to see if it was the cable or not, I swapped them back now that the cable was crimped, and when I hammered it with a file transfer, I saw the same issues pop up again.

So now the question is, these NICs I believe use the same controller. So if the controller had an issue, they'd both be weird. If it was physical, I would normally expect to barely get anything working, if at all, not for it to disconnect under load.

I know heat is a thing, but we're connecting to a switch here, so heat output of the clients wouldn't cause a link on the pfSense box to disconnect. That being said, is there some other thing you can think of that would cause this? Or does it sound correct in assuming that that NIC is disconnecting under load, almost like it's a software issue?

[stephenw10]

If it was a software issue though you would expect the NICs to behave the same. Swapping them would make no difference.

Hard to say what might be causing that.

Steve

[jimp]

I agree, if it was software the behavior would be identical on all ports.

There are many subtle ways electronics can fail under load, it's difficult to speculate about why, but usually boils down to heat or some kind of electrical interference which can't be compensated for at high load vs low load.